I am currently running 2.71.0.140. After factory default I still see the "Login" softkey. I am using auto provisioning, so I suppose my configuration file must have an issue. I will post my y000000000000.cfg and the MAC specific
#!version:1.0.0.1
##File header "#!version:1.0.0.1" can not be edited or deleted, and must be placed in the first line.##
#######################################################################################
## Network ##
#######################################################################################
#Configure the duplex mode and the speed of the WAN port.
#0-Auto negotiate (default), 1-Full duplex 10Mbps, 2-Full duplex 100Mbps, 3-Half duplex 10Mbps, 4-Half duplex 100Mbps;
network.internet_port.speed_duplex = 0
#Configure the username and password for PPPOE connection.
#Require reboot;
network.pppoe.user =
network.pppoe.password =
#PC Port Switch.0-Disable 1-Enable(Default)
network.pc_port.enable = 1
#Configure the PC port type; 0-Router, 1-Bridge (default);
#Require reboot;
network.bridge_mode = 1
#Configure the IP address and mask when the PC port is configured as Router.
#Require reboot;
network.pc_port.ip = 10.0.0.1
network.pc_port.mask = 255.255.255.0
#Configure the duplex mode and the speed of the PC port when configured as Router.
#0-Auto negotiate (default), 1-Full duplex 10Mbps, 2-Full duplex 100Mbps, 3-Half duplex 10Mbps, 4-Half duplex 100Mbps;
network.pc_port.speed_duplex = 0
#Enable or disable the DHCP server when the PC port is configured as Router; 0-Disabled, 1-Enabled (default);
#Require reboot;
network.pc_port.dhcp_server = 1
#Define the DHCP IP address range. The default is from 10.0.0.10 to 10.0.0.100.
network.dhcp.start_ip = 10.0.0.10
network.dhcp.end_ip = 10.0.0.100
#Enable or disable the VLAN of WAN prot; 0-Disabled (default), 1-Enabled;
#Require reboot;
network.vlan.internet_port_enable = 0
#Configure the VLAN ID, it ranges from 0 to 4094, the default value is 0.
#Require reboot;
network.vlan.internet_port_vid = 0
#Configure the VLAN priority, it ranges from 0 (default) to 7.
#Require reboot;
network.vlan.internet_port_priority = 0
#Enable or disable the VLAN of PC port; 0-Disabled (default), 1-Enabled;
#Require reboot;
network.vlan.pc_port_enable = 0
#Configure the VLAN ID, it ranges from 0 to 4094, the default value is 1.
#Require reboot;
network.vlan.pc_port_vid = 1
#Configure the VLAN priority, it ranges from 0 (default) to 7.
#Require reboot;
network.vlan.pc_port_priority = 0
#Enable or disable the DHCP to obtain the information of the VLAN; 0-Disabled; 1-Enabled (default);
#Require reboot;
network.vlan.dhcp_enable = 0
#Configure the DHCP option to obtain the information of the VLAN. It ranges from 0 to 255.
#Multiple options separated by a comma. It supports up to 5 options in all.
#Require reboot;
network.vlan.dhcp_option =
#Configure the transmit package mode when the VLAN of PC port is enabled;
#0-The package is not treated and forwarded directly from PC port to the WAN port;
#1-The package is added the tag and forwarded from PC port to the WAN port, if the package is not the tag.
#Require reboot;
network.vlan.pc_port_mode = 0
#Configure the HTTP port (80 by default) and the HTTPS port (443 by default) of the web server. Both range from 1 to 65535.
#Require reboot;
network.port.http = 80
network.port.https = 443
#Enable or disable the https access. 1-Enable. 0-Disable.
wui.https_enable = 1
wui.http_enable = 1
#Configure the maximum local RTP port. It ranges from 0 to 65535, the default value is 11800.
#Require reboot;
network.port.max_rtpport = 11800
#Configure the minimum local RTP port. It ranges from 0 to 65535, the default value is 11780.
#Require reboot;
network.port.min_rtpport = 11780
#Configure the voice QOS. It ranges from 0 to 63, the default value is 46.
#Require reboot;
network.qos.rtptos = 46
#Configure the SIP QOS. It ranges from 0 to 63, the default value is 26.
#Require reboot;
network.qos.signaltos = 26
#Configure the 802.1x mode; 0-Disabled (default), 1-EAP-MD5, 2-EAP-TLS, 3-PEAP-MSCHAPV2;
#Require reboot;
network.802_1x.mode = 0
#Configure the username and password for 802.1x authentication.
#Require reboot;
network.802_1x.identity =
network.802_1x.md5_password =
#Configure the access URL of the root and client certificates.
network.802_1x.root_cert_url =
network.802_1x.client_cert_url =
#Enable or disable the VPN feature; 0-Disabled (default), 1-Enabled;
#Require reboot;
network.vpn_enable = 0
#Enable or disable the LLDP feature; 0-Disabled, 1-Enabled (default);
#Require reboot;
network.lldp.enable = 1
#Configure the interval(in seconds) the phone broadcasts the LLDP request. It ranges from 1 to 3600, the default value is 60.
#Require reboot;
network.lldp.packet_interval = 60
#Enable or disable the SNMP feature; 0-Disabled (default), 1-Enabled;
#Require reboot;
network.snmp.enable = 0
#Configure the SNMP port.
#Require reboot;
network.snmp.port =
#Configure the IP address(es) of the trusted SNMP server,multiple IP addresses must be separated by a space.
#Require reboot;
network.snmp.trust_ip =
#Enable or disable the span from WAN port to PC port feature; 0-Disabled (default), 1-Enabled;
#Require reboot;
network.span_to_pc_port = 0
#Configure the phone whether to add the MAC address to the User-Agent header; 0-Do not add, 1-Add;
#Require reboot;
network.sip.tag_mac_to_ua.enable = 0
#It enables or disables the phone to use the static DNS.0-Disabled,1-Enabled,The default value is 0.
network.static_dns_enable = 0
#######################################################################################
## Hostname ##
#######################################################################################
#It configures the host name of the phone.The default value is SIP-T2xP (X=0,2,6,8)
network.dhcp_host_name =
#######################################################################################
## Syslog Server ##
#######################################################################################
#Configure the IP address of the syslog server.
#Require reboot;
syslog.server =
#Configure the syslog type. 0-Local(default), 1-Server.
syslog.mode =
#Configure the syslog level. It ranges from 0 to 6, the default value is 3.
#Require reboot;
syslog.log_level =
#######################################################################################
## TR069 ##
#######################################################################################
#The TR069 feature is only applicable to some designated firmware version.
#All settings of TR069 require reboot.
#Enable or disable the TR069 feature; 0-Disabled (default), 1-Enabled;
managementserver.enable = 0
#Configure the username and password for the phone to authenticate with the ACS.
managementserver.username =
managementserver.password =
#Configure the access URL of the ACS.
managementserver.url =
#Configure the username and password for the phone to authenticate the connection requests.
managementserver.connection_request_username =
managementserver.connection_request_password =
#Enable or disable the phone to inform its configuration to the ACS; 0-Disabled (default), 1-Enabled;
managementserver.periodic_inform_enable =
#Configure the interval (in seconds) the phone to inform its configuration to the ACS. The default value is 60.
managementserver.periodic_inform_interval =
#######################################################################################
## Auto Provisioning ##
#######################################################################################
#Configure the auto provision mode;
#0-Disabled (default), 1-Power on, 4-Repeatedly, 5-Weekly, 6-Power on + Repeatedly, 7-Power on + Weekly;
auto_provision.mode = 1
#Enable or disable the Plug and Play feature; 0-Disabled, 1-Enabled (default);
auto_provision.pnp_enable = 0
#Configure the domain name of the PNP server.
auto_provision.pnp_domain_name =
#Configure the value (manufacturer of the device) of the PNP subscribe message.
auto_provision.pnp_event_vendor =
#Configure the interval (in minutes) for the phone to check new configuration files. It ranges from 1 to 43200, the default value is 1440.
#It is only applicable to "Repeatedly" and "Power on + Repeatedly" modes.
auto_provision.schedule.periodic_minute =
#Configure the start time of the day for the phone to check new configuration files. The default value is 00:00.
#It is only applicable to "Weekly" and "Power on + Weekly" modes.
#If the desired start time of the day is seven forty-five a.m., the value format is 07:45.
auto_provision.schedule.time_from =
#Configure the end time of the day for the phone to check new configuration files. The default time is 00:00.
#It is only applicable to "Weekly" and "Power on + Weekly" modes.
#If the desired end time of the day is seven forty-five p.m., the value format is 19:45.
auto_provision.schedule.time_to =
#Configure the day of week for the phone to check new configuration files. The default vaule is 0123456.
#0-Sunday,1-Monday,2-Tuesday,3-Wednesday,4-Thursday,5-Friday,6-Saturday;
#It is only applicable to "Weekly" and "Power on + Weekly" modes.
#If the desired week is Monday, Tuesday and Wednesday, the value format is 012.
auto_provision.schedule.dayofweek =
#Configure the URL of the auto provisioning server.
auto_provision.server.url = 172.16.0.88
#Configure the username and password for downloading.
auto_provision.server.username =
auto_provision.server.password =
#Configure the name of the common file.
#T28P: y000000000000.cfg, T26P: y000000000004.cfg, T22P: y000000000005.cfg, T20P: y000000000007.cfg;
auto_provision.common_file_name = y000000000000.cfg
#Enable or disable DHCP option mode; 0-Disabled, 1-Enabled (default);
auto_provision.dhcp_option.enable = 1
#Configure the value (manufacturer of the device) of DHCP option 60.
auto_provision.dhcp_option.option60_value =
#Configure the custom DHCP option number. It ranges from 128 to 254.
auto_provision.dhcp_option.list_user_options = 150
auto_provision.aes_key_in_file =Â
#Configure AES key (16 characters) for decrypting the common CFG file.
auto_provision.aes_key_16.com =
#Configure AES key (16 characters) for decrypting the MAC-Oriented CFG file.
auto_provision.aes_key_16.mac =
#Configure the mode of downloading configuration files for the phone. The value is 0(default) or 1.
auto_provision.update_file_mode = 0
#######################################################################################
## Auto Provisioning Code ##
#######################################################################################
#This feature allows user to trigger the auto provisioning by pressing a predefined string on the phone.
#Require reboot;
#"X" ranges from 1 to 50
#Configure the auto provisioning name.
#The valid value is a string, the maximum length is 100.
#autoprovision.X.name =
#Configure the auto provisioning code;
#The valid value is a string, the maximum length is 100.
#autoprovision.X.code =
#Configure the URL of the auto provisioning server.
#The valid value is a string, the maximum length is 256.
#autoprovision.X.url =
#Configure the username and password for downloading.
#The valid value is a string, the maximum length is 100.
#autoprovision.X.user =
#autoprovision.X.password =
#Configure AES key (16 characters) for decrypting the common CFG file and MAC-Oriented CFG file.
#autoprovision.X.com_aes =
#autoprovision.X.mac_aes =
autoprovision.1.name = Update Configuration
autoprovision.1.code = 123456789
autoprovision.1.url = tftp://172.16.0.88
autoprovision.1.user =
autoprovision.1.password =
autoprovision.1.com_aes =
autoprovision.1.mac_aes =
autoprovision.2.name =
autoprovision.2.code =
autoprovision.2.url =
autoprovision.2.user =
autoprovision.2.password =
autoprovision.2.com_aes =
autoprovision.2.mac_aes =
#######################################################################################
## Phone Features ##
#######################################################################################
#Enable or disable the phone to escape the pound key as percent sign followed by 23 when dialing out; 0-Disabled, 1-Enabled (default);
sip.use_23_as_pound = 1
#Enable or disable the RFC2543 Hold feature; 0-Disabled (default), 1-Enabled;
sip.rfc2543_hold = 0
#Enable or disable the phone to keep sending the SIP messages to the outbound server; 0-Disabled, 1-Enabled (default);
sip.use_out_bound_in_dialog = 1
#Configure the registration random time (in seconds). It ranges from 0 (default) to 60.
sip.reg_surge_prevention = 0
#Enable or disable the WatchDog feature; 0-Disabled, 1-Enabled (default);
watch_dog.enable = 1
#Enable or disable the transferee to display the missed call prompt when receiving a semi_attended transfer call;
#0-Disabled, 1-Enabled (default);
transfer.semi_attend_tran_enable = 1
#Enable or disable the phone to complete the blind or attended transfer through on-hook;
#0-Disabled,1-Enabled(default);
transfer.blind_tran_on_hook_enable = 1
transfer.on_hook_trans_enable = 1
#Define the way of DSS key when configuring as a transfer key; 0-Display Number, 1-Attended Transfer, 2-Blind Transfer (default);
transfer.dsskey_deal_type = 2
#Enable or disable the phone to enter the transfer to interface during two calls when pressing the transfer soft key or TRAN key; 0-Disable, 1-Enabled (default);
transfer.multi_call_trans_enable = 1
#Enable or disable the conference initiator to transfer the call when hanging up.
#0-Disabled(default),1-Enabled;
transfer.tran_others_after_conf_enable = 1
#######################################################################################
## Call Forward ##
#######################################################################################
#Configure the call forward key mode; 0-Phone mode (default), 1-Custom mode.
features.fwd_mode = 0
#Enable or disable the always forward feature; 0-Disabled (default), 1-Enabled;
forward.always.enable = 0
#Configure the target number that the phone will forward the call to.
forward.always.target =
#Configure the always forward on code and off code.
forward.always.on_code =
forward.always.off_code =
#Enable or disable the busy forward feature; 0-Disabled (default), 1-Enabled;
forward.busy.enable = 0
forward.busy.target =
forward.busy.on_code =
forward.busy.off_code =
#Enable or disable the no answer forward feature; 0-Disabled (default), 1-Enabled;
#Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 2.
forward.no_answer.enable = 0
forward.no_answer.target =
forward.no_answer.timeout =
forward.no_answer.on_code =
forward.no_answer.off_code =
#Enable or disable the phone to forward the call to the international number (the prefix is 00); 0-Disabled (default), 1-Enabled;
forward.international.enable =
#######################################################################################
## DND ##
#######################################################################################
#Configure the DND key mode; 0-Phone mode (default), 1-Custom mode.
features.dnd_mode = 0
#Configure the DND on code and off code.
features.dnd.on_code =
features.dnd.off_code =
#It enables or disables the phone to recevice incoming calls from authorized numbers when DND feature is enabled.0-Disabled,1-Enabled.The default value is 0.
features.dnd.emergency_enable = 0
#It configures the numbers the phone will receive incoming calls from when DND feature is enabled.Multiple numbers are separated by comma.The default value is blank.
features.dnd.emergency_authorized_number =
#######################################################################################
## Voice ##
#######################################################################################
#Enable or disable the voice activity detection feature; 0-Disbaled (default), 1-Enabled;
voice.vad = 0
#Enable or disable the comfortable noise generator; 0-Disabled, 1-Enabled (default);
voice.cng = 1
#Enable or disable the echo canceller; 0-Disabled, 1-Enabled (default);
voice.echo_cancellation = 1
#Configure the volume of the side tone. It ranges from -48 to 0, the default value is -3.
voice.side_tone= -3
#Configure the sending volume of Speaker, Handset and Headset. It ranges from 1 to 53, the default values are 25, 35, 29.
#Require reboot;
voice.handfree_send = 25
voice.handset_send = 35
voice.headset_send = 29
#Configure the type of jitter buffer; 0-Fixed, 1-Adaptive (default);
voice.jib.adaptive = 1
#Configure the minimum delay, maximum delay and normal delay. The default values are 0, 300, 120.
voice.jib.min = 0
voice.jib.max = 300
voice.jib.normal = 120
#Define the voice tone, the valid values can be Custom (default) or voice tone of different countries. For example, United States, France, Germany and so on.
#voice.tone.country = Custom
voice.tone.country = United States
#Customize the tone when the "voice.tone.country" is configured as Custom.
#The value format: Frequency/Duration.
#Frequency ranges from 200 to 7000. When 0 is used to define the frequency, it means a pause between tones.
#A tone can be composited at most four different frequencies (the value format is: F1+F2+F3+F4).
#Duration is the time duration (in milliseconds) of ringing the tone. It ranges from 0 to 30000ms.
#At most eight tones can be configured for dial, ring, busy and so on, each tone is separated by a comma.
#For example, voice.tone.dial = 100/200,200/150,300+400+500+1200/1000,0/1200,500+900/800,5000+2000+3000/6000,0/1500,3600/1800
voice.tone.dial =
voice.tone.ring =
voice.tone.busy =
voice.tone.congestion =
voice.tone.callwaiting =
voice.tone.dialrecall =
voice.tone.record=
voice.tone.info =
voice.tone.stutter =
voice.tone.message =
voice.tone.autoanswer =
#Configure the receiving volume of Speaker, Handset and Headset. It ranges from 0 to 15, the default value is 8.
voice.handfree.spk_vol = 8
voice.handset.spk_vol = 8
voice.headset.spk_vol = 8
#Configure the dial tone volume of Speaker, Handset and Headset. It ranges from 0 to 15, the default value is 8.
voice.handfree.tone_vol = 8
voice.handset.tone_vol = 8
voice.headset.tone_vol = 8
#configure the preview call mode; 1-Ignore:the mixed of tone and RTP (default), 2-Force: discard the RTP and play the tone, 3-Skip: skip the tone to play the RTP;
voice.call_preview_mode= 1
#######################################################################################
## Security Settings ##
#######################################################################################
#Enable or disable the phone to only accept the certificates in the Trusted Certificates list;
#0-Disabled, 1-Enabled (default);
security.trust_certificates =
#Define the login username and password of the user, var and administrator.
#If you change the username of the administrator from "admin" to "admin1", your new administrator's username should be configured as: security.user_name.admin = admin1.
#If you change the password of the administrator from "admin" to "admin1pwd", your new administrator's password should be configured as: security.user_password = admin1:admin1pwd.
#The following examples change the user's username to "user23" and the user's password to "user23pwd".
#security.user_name.user = user23
#security.user_password = user23:user23pwd
#The following examples change the var's username to "var55" and the var's password to "var55pwd".
#security.user_name.var = var55
#security.user_password = var55:var55pwd
security.user_name.user =
security.user_name.admin =
security.user_name.var =
security.user_password =
#Enable or disable the 3-level permissions (open var); 0-Disabled (default), 1-Enabled;
#Require reboot;
security.var_enable =
#######################################################################################
## Customize the softkey ##
#######################################################################################
#Customize the softkeys presented on the phone LCD screen when Callfailed, Callin, Connecting, Dialing, Ringback and Talking.
#Before using these parameters, you should store the desired XML files to the provisioning server.
custom_softkey_call_failed.url =
custom_softkey_call_in.url =
custom_softkey_connecting.url =
custom_softkey_dialing.url =
custom_softkey_ring_back.url =
custom_softkey_talking.url =
#######################################################################################
## Line Key ##
#######################################################################################
#The x of the parameter "linekey.x.line" ranges from 1 to 6.
#The default value equals to the value of x. For example, the default value of the parameter "linekey.1.line" is 1.
#For T28P, the value of the "linekey.X.line" ranges from 0 to 6. The value 0 or 1 of the "linekey.x.line" stands for line 1£¬The value 2 of the "linekey.x.line" stands for line 2
#linekey.x.lable--Define the label for each line key.
#Configure Line Key1
linekey.1.line = 0
linekey.1.value =
linekey.1.pickup_value =
linekey.1.type = 15
linekey.1.xml_phonebook =
linekey.1.label = Ext 1100
#Configure Line Key2
linekey.2.line = 0
linekey.2.value =
linekey.2.pickup_value =
linekey.2.type = 15
linekey.2.xml_phonebook =
linekey.2.label = Ext 1100
#Configure Line Key3
linekey.3.line = 0
linekey.3.value =
linekey.3.pickup_value =
linekey.3.type = 15
linekey.3.xml_phonebook =
linekey.3.label = Ext 1100
#Configure Line Key4 (for T28P only)
linekey.4.line = 0
linekey.4.value =
linekey.4.pickup_value =
linekey.4.type = 15
linekey.4.xml_phonebook =
linekey.4.label = Ext 1100
#Configure Line Key5 (for T28P only)
linekey.5.line = 0
linekey.5.value =
linekey.5.pickup_value =
linekey.5.type = 15
linekey.5.xml_phonebook =
linekey.5.label = Ext 1100
#Configure Line Key6 (for T28P only)
linekey.6.line = 0
linekey.6.value =
linekey.6.pickup_value =
linekey.6.type = 50
linekey.6.xml_phonebook =
linekey.6.label = Lock
##########################################################################################
## Programmable Key ##
##########################################################################################
#X ranges from 1 to 15.
#programablekey.x.type--Customize the programmable key type.
#The valid types are:
#0-N/A 2-Forward 5-DND 6-Redial 7-Call Return 8-SMS 9-Direct Pickup 13-Spead Dial
#22-XML Group 23-Group Pickup 27-XML Browser 28-History 30-Menu 31-Switch Account 32-New SMS
#33-Status 40-PTT 43-Local Phonebook 44-Broadsoft Phonebook 45-Local Group 46-Broadsoft Group 47-XML Phonebook 50-Keypad Lock
#55-meet me 56-retrieve park 58-ACD Trace 59-disp code 60-Emergency 61-Directory
#PTT-add a specified prefix number before the dialed number.
#programablekey.x.line--Configure the desired line to apply the key feature. It ranges from 0 to 6.
#The value 0 or 1 of the "proramablekey.x.line" stands for line1, it means the first available line.
#programablekey.x.value =
#programablekey.x.xml_phonebook--Specify the desired remote phonebook/local group/BSFT phonebook for the programmable key. This parameter is only applicable to the feature XML Group/Local Group/Broadsoft Group.
#0-the first phonebook£¬1-the second phonebook£¬and so on.
#programablekey.x.history_type =
#0-local calllog£¬1-network calllog.
#programablekey.x.label--This parameter is only available to the key 1 to key 4.
programablekey.1.type = 28
programablekey.1.line = 0
programablekey.1.value =
programablekey.1.xml_phonebook =
programablekey.1.history_type =
programablekey.1.label = History
programablekey.2.type = 47
programablekey.2.line = 0
programablekey.2.value =
programablekey.2.xml_phonebook =
programablekey.2.history_type =
programablekey.2.label = Directory
programablekey.3.type = 5
programablekey.3.line = 0
programablekey.3.value =
programablekey.3.xml_phonebook =
programablekey.3.history_type =
programablekey.3.label = DND
programablekey.4.type = 30
programablekey.4.line = 0
programablekey.4.value =
programablekey.4.xml_phonebook =
programablekey.4.history_type =
programablekey.4.label = Menu
##########################################################################################
## Expansion Key ##
##########################################################################################
#X ranges from 1 to 16, Y ranges from 1 to 40.
#expansion_module.x.key.y.type = 37 (Switch by default)
#expansion_module.x.key.y.line = 0
#expansion_module.x.key.y.value =
#expansion_module.x.key.y.pickup_value =
#expansion_module.x.key.y.label =
#expansion_module.X.key.Y.xml_phonebook =
#Each expansion module1 key1
expansion_module.1.key.1.type = 37
expansion_module.1.key.1.line = 0
expansion_module.1.key.1.value =
expansion_module.1.key.1.pickup_value =
expansion_module.1.key.1.label = Switch
expansion_module.1.key.1.xml_phonebook =
#Each expansion module1 key2
expansion_module.1.key.2.type = 16
expansion_module.1.key.2.line = 0
expansion_module.1.key.2.value = 102
expansion_module.1.key.2.pickup_value =
expansion_module.1.key.2.label = Demo 7945
expansion_module.1.key.2.xml_phonebook =
#Each expansion module2 key1
expansion_module.2.key.1.type = 37
expansion_module.2.key.1.line = 0
expansion_module.2.key.1.value =
expansion_module.2.key.1.pickup_value =
expansion_module.2.key.1.label = Page
expansion_module.2.key.1.xml_phonebook =
#Each expansion module2 key2
expansion_module.2.key.1.type = 16
expansion_module.2.key.1.line = 0
expansion_module.2.key.1.value = 103
expansion_module.2.key.1.pickup_value =
expansion_module.2.key.1.label = Demo 7941
expansion_module.2.key.1.xml_phonebook =
#######################################################################################
## Automatic Call Distribute ##
#######################################################################################
#Enable or disable the phone to automatically change the phone status to available; 0-Disabled (default), 1-Enabled;
acd.auto_available =
#Configure the interval (in seconds) to automatically turn the state of the ACD agent to available. It ranges from 0 to 120, the default value is 60.
acd.auto_available_timer =
#######################################################################################
# Action URL Settings ##
#######################################################################################
#action_url.setup_completed--Inform the server that the phone has completed the startup.
#action_url.dnd_on-- Inform the server that the DND is activated on the phone.
#The value format is: http://IP address of server/help.xml?variable name=variable value.
#The valid variable values are: $mac--MAC address of phone, $ip--The current IP address of phone, $model--Phone model, $firmware--Phone firmware version.
#$active_url--The SIP URI of the current account when the phone is in the incoming state, outgoing state or during conversation.
#$active_user--The username of the current account when the phone is in the incoming state, outgoing state or during conversation.
#$active_host--The host name of the current account when the phone is in the incoming state, the outgoing state or during conversation.
#$local--The SIP URI of the caller when outgoing calls or the SIP URI of the callee when receiving calls.
#$remote--The SIP URI of the callee when outgoing calls or the SIP URI of the caller when receiving calls.
#$display_local--The display name of the caller when outgoing calls or the display name of the callee when receiving calls.
#$display_remote--The display name of the callee when outgoing calls or the display name of the caller when receiving calls.
#$call_id--The caller ID when in the incoming state, the outgoing state or during conversation.
#For example, action_url.log_on =
http://192.168.1.20/help.xml?mac=$mac
action_url.setup_completed =
action_url.log_on =
action_url.log_off =
action_url.register_failed =
action_url.off_hook =
action_url.on_hook =
action_url.incoming_call =
action_url.outgoing_call =
action_url.call_established =
action_url.dnd_on =
action_url.dnd_off =
action_url.always_fwd_on =
action_url.always_fwd_off =
action_url.busy_fwd_on =
action_url.busy_fwd_off =
action_url.no_answer_fwd_on =
action_url.no_answer_fwd_off =
action_url.transfer_call =
action_url.blind_transfer_call =
action_url.attended_transfer_call =
action_url.hold =
action_url.unhold =
action_url.mute =
action_url.unmute =
action_url.missed_call =
action_url.call_terminated =
action_url.busy_to_idle =
action_url.idle_to_busy =
action_url.ip_change =
action_url.answer_new_incoming_call =
action_url.reject_incoming_call =
action_url.transfer_finished =
action_url.transfer_failed =
action_url.forward_incoming_call =
#######################################################################################
## Language Settings ##
#######################################################################################
#Specify the web language, the valid values are: English, Chinese_S, Turkish, Portuguese, Spanish, Italian, French, Russian, Deutsch and Czech.
lang.wui = English
#Specify the LCD language, the valid values are: English (default), German, French, Turkish, Italian, Polish, Spanish and Portuguese.
#lang.gui = English
lang.gui = English
#######################################################################################
## Time Settings ##
#######################################################################################
#Configure the time zone and time zone name. The time zone ranges from -11 to +12, the default value is +8.
#The default time zone name is China(Beijing).
#Refer to Yealink IP Phones User Guide for more available time zones and time zone names.
#local_time.time_zone = +8
#local_time.time_zone_name = China(Beijing)
local_time.time_zone = -7
local_time.time_zone_name = Mountain
#Configure the domain name or the IP address of the NTP server. The default value is cn.pool.ntp.org.
local_time.ntp_server1 = 66.60.100.1
local_time.ntp_server2 = pool.ntp.org
#Configure the update interval (in seconds) when using the NTP server. The default value is 1000.
local_time.interval = 1000
#Configure the daylight saving time feature; 0-Disabled, 1-Enabled, 2-Automatic (default);
local_time.summer_time = 2
#Configure the DST type when the DST feature is enabled; 0-By Date (default), 1-By Week;
local_time.dst_time_type =
#Configure the start time of DST. The default value is 1/1/0.
#If the DST type is configured as By Date, the value format is Month/Day/Hour. For example, the value 5/20/10 means the start time is at 10:00 on May 20.
#If the DST type is configured as By Week, the value format is Month/Day of Week/Day of Week Last in Month/Hour of Day.
#For example, the value 1/4/2/5 means the start time is at 5 o'clock on Tuesday of the 4th week in January.
local_time.start_time =
#Configure the end time of DST. The default value is 12/31/23. The value format is the same to the start time.
local_time.end_time =
#Configure the offset time (in seconds). It ranges from -300 to 300, the default value is 60.
local_time.offset_time =
#Configure the time format; 0-12 Hour, 1-24 Hour (default);
local_time.time_format =
#Configure the date format; 0-WWW MMM DD (default), 1-DD-MMM-YY, 2-YYYY-MM-DD, 3-DD/MM/YYYY, 4-MM/DD/YY, 5-DD MMM YYYY, 6-WWW DD MMM;
local_time.date_format =
#Enable or disable the DHCP Time; 0-Disabled (default), 1-Enabled;
local_time.dhcp_time =
#Enable or disable the manual time setting. 0-Disabled (default), 1-Enabled;
local_time.manual_time_enable =
#######################################################################################
## Hot Desking ##
#######################################################################################
#Enable or disable the phone to show the following items on the login wizard during startup; 0-Disabled, 1-Enabled;
#hotdesking.startup_register_name_enable = 1 (default)
#hotdesking.startup_username_enable = 1 (default)
#hotdesking.startup_password_enable = 0 (default)
#hotdesking.startup_sip_server_enable = 0 (default)
#hotdesking.startup_outbound_enable = 0 (default)
hotdesking.startup_register_name_enable = 0
hotdesking.startup_username_enable = 0
hotdesking.startup_password_enable = 0
hotdesking.startup_sip_server_enable = 0
hotdesking.startup_outbound_enable = 0
#Enable or disable the phone to show the following items on the login wizard when pressing the Hot Desking DSS key;
#0-Disabled, 1-Enabled;
#hotdesking.dsskey_register_name_enable = 1 (default)
#hotdesking.dsskey_username_enable = 1 (default)
#hotdesking.dsskey_password_enable = 0 (default)
#hotdesking.dsskey_sip_server_enable = 0 (default)
#hotdesking.dsskey_outbound_enable = 0 (default)
hotdesking.dsskey_register_name_enable = 0
hotdesking.dsskey_username_enable = 0
hotdesking.dsskey_password_enable = 0
hotdesking.dsskey_sip_server_enable = 0
hotdesking.dsskey_outbound_enable = 0
#######################################################################################
## Distinctive Ring Tones ##
#######################################################################################
#"X" ranges from 1 to 10;
#Configure the text to map the keywords contained in the "Alert-info" header.
#distinctive_ring_tones.alert_info.X.text = family
distinctive_ring_tones.alert_info.1.text =
#Specify the ring tone for each text. It ranges from 1 to 8. The default value 1 stands for Ring1.wav.
#1-Ring1.wav, 2-Ring2.wav, 3-Ring3.wav, 4-Ring4.wav, 5-Ring5.wav, 6-Ring6.wav, 7-Ring7.wav, 8-Ring8.wav.
#distinctive_ring_tones.alert_info.X.ringer = 1
distinctive_ring_tones.alert_info.1.ringer =
#######################################################################################
## Auto Redial ##
#######################################################################################
#Enable or disable the auto redial feature; 0-Disabled (default), 1-Enabled;
auto_redial.enable =
#Configure the interval (in seconds) to wait before redial. It ranges from 1 to 300. The default value is 10.
auto_redial.interval =
#Configure the auto redial times. It ranges from 1 to 300. The default value is 10.
auto_redial.times =
#######################################################################################
## Zero Touch ##
#######################################################################################
#Enable or disable the Zero Touch feature; 0-Disabled (default), 1-Enabled;
zero_touch.enable =
#Configure the waiting time (in seconds) before canceling the Zero Touch. It ranges from 0 to 100, the default value is 5.
zero_touch.wait_time =
#######################################################################################
## Push XML ##
#######################################################################################
push_xml.server =
#Enable or disable the phone to display the push XML interface when receiving an incoming call; 0-Disabled (default), 1-Enabled;
push_xml.block_in_calling =
#Enable or disable the phone to use the push XML via SIP Notify message; 0-Disabled (default), 1-Enabled;
push_xml.sip_notify =
#######################################################################################
## Dial Plan ##
#######################################################################################
#Configure the area code;
dialplan.area_code.code =
dialplan.area_code.min_len = 1
dialplan.area_code.max_len = 15
#When applying the rule to multiple lines, each line ID separated by a comma.
#e.g. dialplan.area_code.line_id = 1,2,3
dialplan.area_code.line_id =
#Configure the block out number. X ranges from 1 to 10.
#dialplan.block_out.number.x =
dialplan.block_out.number.1 =
#When applying the rule to multiple lines, mutiple lines must be separated by a comma. E.g. 1,2,3.
#dialplan.block_out.line_id.X =
dialplan.block_out.line_id.1 =
#Configure the replace rule. X ranges from 1 to 20.
#dialplan.item.X = Enabled,Prefix,Replaced,LineID
#Enabled: Enable or disable the replace rule. 0-Disabled, 1-Enabled; Prefix: Specify the numbers that need replacing;
#Replaced: Specify the alternate numbers;
#LineID: Specify the line ID to apply the replace rule,multiple lines ID must be separated by a comma;
dialplan.item.1 =
#Configure the dialnow rule. X ranges from 1 to 20.
#dialnow.item.X = Dial-now rule,Line ID
#Dial-now rule: Specify the numbers that need replacing;
#Line ID:Specify the line ID to apply the replace rule,multiple lines must be separated by a comma;
dialnow.item.1 =
dialplan.dialnow.rule.X =
dialplan.dialnow.line_id.X =
dialplan.replace.prefix.X =
dialplan.replace.replace.X =
dialplan.replace.line_id.X =
#######################################################################################
## BSFT Phonebook ##
#######################################################################################
#Configuration of BW phonebook. X ranges from 1 to 6.
#bw_phonebook.data.X.server =
#bw_phonebook.data.X.port =
#bw_phonebook.data.X.username =
#bw_phonebook.data.X.password =
#bw_phonebook.data.X.name =
bw_phonebook.data.1.server =
bw_phonebook.data.1.port =
bw_phonebook.data.1.username =
bw_phonebook.data.1.password =
bw_phonebook.data.1.name =
#Configure the search parameter of Broadsoft phonebook version 1.0, mutiple parameters must be separated by a "&"symbol.
bw_phonebook.search_params_v1 =
#Configure the search parameter of Broadsoft phonebook version 2.0, mutiple parameters must be separated by a "&"symbol.
bw_phonebook.search_params_v2 =
#Configure the mode of search parameters; 0-AND, 1-OR (default); The vaule only works in Broadsoft phonebook verion 2.0;
bw_phonebook.search_mode_or =
#######################################################################################
## BSFT Call Log ##
#######################################################################################
#Configuration of the BW call log. X ranges from 1 to 3.
#bw_call_log.data.X.server =
#bw_call_log.data.X.port =
#bw_call_log.data.X.username =
#bw_call_log.data.X.password =
#bw_call_log.data.X.name =
bw_call_log.data.1.server =
bw_call_log.data.1.port =
bw_call_log.data.1.username =
bw_call_log.data.1.password =
bw_call_log.data.1.name =
#Enable or disable the phone to access the BSFT call log/phonebook directly when pressing the History/Directory soft keys;
#0-Disabled (default), 1-Enabled;
#Require reboot;
bw.calllog_and_dir =
#Specify whether to display the BSFT call log on the web user interface; 0-Disabled, 1-Enabled (default);
#Require reboot;
bw.behave_calllog =
#Specify whether to display the BSFT directory on the web user interface; 0-Disabled, 1-Enable (default);
#Require reboot;
bw.directory_enable =
#Enable or disable the feature key synchronization; 0-Disabled (default), 1-Enabled;
bw.feature_key_sync =
#######################################################################################
## Remote phonebook ##
#######################################################################################
#Configure the access URL and dispaly name of the remote phonebook. X ranges from 1 to 5.
#remote_phonebook.data.X.url =
#remote_phonebook.data.X.name =
remote_phonebook.data.1.url =
http://172.16.0.88/ciscodirectory.xml
remote_phonebook.data.1.name = Company Directory
#######################################################################################
## LDAP Settings ##
#######################################################################################
#Configure the search criteria for name and number lookups.
ldap.name_filter =
ldap.number_filter =
ldap.host = 0.0.0.0
ldap.port = 389
ldap.base =
ldap.user =
ldap.password =
#Specify the maximum of the displayed search results. It ranges from 1 to 32000, the default value is 50.
ldap.max_hits =
ldap.name_attr =
ldap.numb_attr =
ldap.display_name =
#Configure the LDAP version. The valid value is 2 or 3 (default).
ldap.version =
#Conifugre the search delay time. It ranges from 0 (default) to 2000.
ldap.search_delay =
#Enable or disable the phone to query the contact name from the LDAP server when receiving an incoming call; 0-Disabled (default), 1-Enabled;
ldap.call_in_lookup =
#Enable or disable the phone to sort the search results in alphabetical order; 0-Disabled (default), 1-Enabled;
ldap.ldap_sort =
#Enable or disable the phone to query the LDAP server when in the pre-dialing or the dialing state; 0-Disabled (default), 1-Enabled;
ldap.dial_lookup =
#######################################################################################
## Phone Features ##
#######################################################################################
#Configure the return code when activating DND; 404-No Found, 480-Temporarily not available (default), 486-Busy here;
#features.dnd_refuse_code = 480
features.dnd_refuse_code =
#Configure the return code when refusing a call. The valid values are 404, 480, 486 (default).
features.normal_refuse_code =
#Enable or disable the call completion feature; 0-Disabled (default), 1-Enabled;
features.call_completion_enable =
#Configure the LED flashing mode of the BLF key (line key). The value is 0(default) or 1.
features.blf_led_mode =
#Enable or disable the call waiting feature; 0-Disabled, 1-Enabled (default);
call_waiting.enable =
#It configures the call waiting on code.The default value is blank.
call_waiting.on_code =
#It configures the call waiting off code.The default value is blank.
call_waiting.off_code =
#Enable or disable the playing of call waiting tone; 0-Disabled, 1-Enabled (default);
call_waiting.tone =
#Enable or disable the intercom feature; 0-Disabled, 1-Enabled (default);
features.intercom.allow =
#Enable or disable the phone to mute the Speaker when answering an intercom call; 0-Disabled (default), 1-Enabled;
features.intercom.mute =
#Enable or disable the phone to play the intercom warning tone; 0-Disabled, 1-Enabled (default);
features.intercom.tone =
#Enable or disable the phone to barge in an intercom call; 0-Disabled (default), 1-Enabled;
features.intercom.barge =
#Enables or disables the IP phone to query the contact names from the remote phonebook when receiving incoming calls; 0-Disabled (default), 1-Enabled;
features.remote_phonebook.enable =
#Set the interval (in seconds) for the phone to update the information of the remote phonebook. The default value is 21600.
features.remote_phonebook.flash_time =
#Configure the hotline number and delay time (in seconds). It ranges from 0 to 180, the default value is 4.
features.hotline_number =
features.hotline_delay =
#Enable or disable the phone to suppress the display of DTMF digits; 0-Disabled (default), 1-Enabled;
features.dtmf.hide =
#Enables or disables the IP phone to display the DTMF digits for a short period before displaying as asterisks; 0-Disabled (default), 1-Enabled;
features.dtmf.hide_delay =
#Configure the repetition times of DTMF end packet. The valid values are 1, 2, 3 (default).
features.dtmf.repetition =
#Configure DTMF sequences. It can be consisted of digits, alphabets, * and #.
features.dtmf.transfer =
#Enable or disable the phone to send DTMF sequences during a call when pressing the transfer soft key or the TRAN key; 0-Disabled (default), 1-Enabled;
features.dtmf.replace_tran =
#Enable or disable the headset prior feature; 0-Disabled (default), 1-Enabled;
features.headset_prior =
#Enable or disable the dual headset feature; 0-Disabled (default), 1-Enabled;
features.headset_training =
#Configure the delay time (in milliseconds) before transfering a call. The default value is 0.
features.hold_trans_delay =
#Enbale or disable the phone to play a local DTMF tone; 0-Disabled, 1-Enabled (default);
features.play_local_dtmf_tone_enable =
#Enbale or disable the server to release the BLA line automatically; 0-Disabled (default), 1-Enabled;
features.auto_release_bla_line =
#Configure the delay time (in seconds) of playing busy tone when rejecting a call. The valid values are 0 (default), 3 and 5.
features.busy_tone_delay =
#Configure the phone whether to send a pound key when pressing double pound keys; 0-Send one pound key (default), 1-Do not send any pound key;
features.send_pound_key =
#Define the "#" or "*" key as the send key; 0-Disabled, 1-# key(default), 2-* key;
features.pound_key.mode =
#Enable or disable the phone to play tone when pressing the digit key; 0-Disabled, 1-Enabled (default);
features.send_key_tone =
features.key_tone =
#Enable or disable the phone to play a warning tone when there is a held call; 0-Disabled, 1-Enabled (default);
features.play_hold_tone.enable =
#Configure the interval of playing a warning tone. The default value is 30s.
features.play_hold_tone.delay =
features.redial_tone =
#Enable or disable the phone with active accounts to play tones in the dialing interface differently from the phone with no active accounts; 0-Disabled (default), 1-Enbaled;
features.partition_tone =
#Enable or disable the phone to encrypt the digits of the dialed number. The encrypted digits are displayed as asterisks on the LCD screen; 0-Disabled (default), 1-Enabled;
features.password_dial.enable =
#Configure the prefix numbers displayed before the encrypted digits.
features.password_dial.prefix =
#Configure the length of encrypted digits.
features.password_dial.length =
#Enable or disable the phone to diaplay the Save Call Log option on the web user interface; 0-Disabled, 1-Enabled (default);
features.history_save_display =
#Enable or disable the phone to save the call history; 0-Disabled, 1-Enabled (default);
features.save_call_history =
#Configure the power Indicator LED to turn on ro turn off; 0-On (default), 1-Off;
features.power_led_on =
#Specifie the address(es) or enters ¡°any¡± from which Action URI will be accepted.
#For discontinuous IP addresses, each IP address is separated by comma, for example: 192.168.1.20,10.2.1.30
#For continuous IP addresses, the format likes *.*.*.* and the ¡°*¡± stands for the values 0~255. For example: 10.10.*.* stands for the IP addresses that range from 10.10.0.0~10.10.255.255.
#If left blank, the IP phone cannot receive or handle any HTTP GET request.
#If set to ¡°any¡±, the IP phone accepts and handles HTTP GET requests from any IP address.
features.action_uri_limit_ip =
#Configure the delay time (in seconds)of auto answer. The time ranges from 1 to 4, the default value is 1s.
features.auto_answer_delay =
#Enable or disable the transfer DSS key to perform the blind transfer; 0-Disabled, 1-Enabled (default);
features.dsskey_blind_tran =
#Configure the overtime (in minutes) of logging web user interface. It ranges from 1 to 1000, the default value is 5.
features.relog_offtime =
#Enable or disable the phone to dial the IP address directly; 0-Disabled, 1-Enabled (default);
features.direct_ip_call_enable =
#Configure the ringtone of emergency calls;
#features.emergency_ring = Emergency.wav
features.emergency_ring =
#Enable or disable the phone to mute the call during an active call; 0-Disabled, 1-Enabled (default);
features.allow_mute =
#Specify the ring device when the phone is in the Headset mode; 0-use Speaker (default), 1-use Headset;2- Use Headset& Speaker.
features.ringer_device.is_use_headset =
#Enable or disable the phone to pick up the call using the group pickup soft key; 0-Disabled (default), 1-Enabled;
features.pickup.group_pickup_enable =
#Configure the group pickup code.
features.pickup.group_pickup_code =
#Enable or disable the phone to pick up the call using the directed pickup soft key; 0-Disabled (default), 1-Enabled;
features.pickup.direct_pickup_enable =
#Configure the directed pickup code.
features.pickup.direct_pickup_code = **
#Specify the way to notify the phone of the incoming call of the monitored user by visual or audio indicator;
#0-Disabled (default), 1-Enabled;
features.pickup.blf_visual_enable =
features.pickup.blf_audio_enable =
#Configure the input type when the phone is in the dialing state, if the parameter "ldap.dial_lookup" is Enabled; 0-2aB, 1-123 (default), 2-abc, 3-ABC;
features.ldap.input_type =
#Enable or disable the phone to play the warning tone when receiving a vocie mail. 0-Disabled; 1-Enabled(default).
features.voice_mail_tone_enable =
#Blf led switch in idle.0-Disabled; 1-Enabled(default).
features.blf_and_callpark_idle_led_enable =
#Forward Diversion switch. 0-Disabled(default); 1-Enabled
features.fwd_diversion_enable =
#Configure the time (in seconds) the phone automatically dials out the dialed digits. It ranges from 1 to 14, the default value is 4.
phone_setting.inter_digit_time =
#Configure the flash hook time (in milliseconds). It ranges from 0 to 799, the default value is 1.
phone_setting.flash_hook_timer =
#Configure the keypad lock type; 0-Disabled (default), 1-Menu Key, 2-Function Key, 3-All Keys, 4-Lock&Answer;
phone_setting.lock =
#Configure the unlock password for the phone. The default value is 123.
phone_setting.phone_lock.unlock_pin =
#Configures the interval (in seconds) to automatically lock the IP phone. It ranges from 0 to 3600, the default value is 0.
phone_setting.phone_lock.lock_time_out =
#Configure the ring tone for the phone. System ring tones are: Common, Ring1.wav (default), Ring2.wav¡Â¡ÂRing8.wav.
#If you set the custom ring tone (Busy.wav) for the phone, the value is: phone_setting.ring_type = Busy.wav
#If you set the system ring tone (Ring2.wav) for the phone, the value is: phone_setting.ring_type = Ring2.wav
phone_setting.ring_type =
#Configure the contrast of the LCD screen. It ranges from 1 to 10,the default value is 6.
phone_setting.contrast =
#Configure the logo mode of the LCD screen; 0-Disabled (default), 1-System logo, 2-Custom logo;
phone_setting.lcd_logo.mode = 2
#Configure the active backlight level. It ranges from 1 to 3, the default value is 2.
#The same level for different phones may result in different backlight intensities.
phone_setting.active_backlight_level =
#Configure the backlight time (in seconds). The valid values are: 0-Always on, 1-Always off, 15-15s, 30-30s (default), 60-60s, 120-120s.
phone_setting.backlight_time =
#Configure the ring tone when the transfer fails. The valid values are: Ring1.wav.... Ring8.wav.
#phone_setting.ring_for_tranfailed = Ring1.wav
phone_setting.ring_for_tranfailed =
#Enable or disable the phone to show the logon wizard during startup; 0-Disabled (default), 1-Enabled;
phone_setting.logon_wizard =
#Enable or disable the phone to automatically dial out the dialed digits in the pre-dial interface; 0-Disabled (default), 1-Enabled;
phone_setting.predial_autodial =
#Enable or disable the phone to deal the 180 SIP message after the 183 SIP message; 0-Disabled, 1-Enabled (default);
phone_setting.is_deal180 =
#Configure the delay time (in seconds) for the dialnow rule. It ranges from 1 to 14, the default value is 1.
phone_setting.dialnow_delay =
#Enable or disable customizing the softkey layout; 0-Disabled (default), 1-Enabled;
phone_setting.custom_softkey_enable =
#Configure the using mode of the headset key. The value is 0 or 1(default).
phone_setting.headsetkey_mode =
#Configure the emergency number, each separated by a comma. The default value is 112,911,110.
phone_setting.emergency.number =
#Configure the phone whether to end the call when the network is unavailable; 0-End the call, 1-Do not end the call.
phone_setting.end_call_net_disconnect.enable =
#If leaving the field blank, the phone will display the value sent from the server when receiveing the 403 message; otherwise display the value entered in the filed.
#The default value is blank.
phone_setting.show_code403 =
#It configures a text logo.The maximum length of the value is 15 characters(only applicable to T20P IP phone).The default value is Yealink.
phone_setting.lcd_logo.text =
#######################################################################################
## Multicast ##
#######################################################################################
#Configure the codec of multicast paging.
multicast.codec =
#Enbale or diable the phone to handle the incoming multicast paging calls when there is a multicast paging call on the phone; 0-Disabled, 1-Enabled (default);
#If enabled, the phone will answer the incoming multicast paging call with a higher priority and ignore that with a lower priority.
multicast.receive_priority.enable =
#Configure the priority of multicast paging calls. It ranges from 0 to 10.
multicast.receive_priority.priority =
#Configure the listening multicast IP address and port number for the phone. X ranges from 1 to 10.
#multicast.listen_address.X.ip_address =
multicast.listen_address.1.ip_address =
#Configure the lable displayed on the LCD screen when receiving the multicast paging. X ranges from 1 to 10.
#multicast.listen_address.X.label =
multicast.listen_address.1.label =
#######################################################################################
## Configure the access URL of firmware ##
#######################################################################################
#Before using this parameter, you should store the desired firmware (x.70.x.x.rom) to the provisioning server.
firmware.url = tftp://172.16.0.88/2.71.0.140.rom
#######################################################################################
## Configure the access URL of the customized ringtones ##
#######################################################################################
#Before using this parameter, you should store the desired ring tone (x.wav) to the provisioning server.
#For more information, refer to Yealink Auto Provisioning User Guide.
ringtone.url =
#ringtone.delete = http://localhost/all,delete all the customized ring tones.
ringtone.delete =
#######################################################################################
## Configure the access URL of language file ##
#######################################################################################
#Before using this parameter, you should store the desired language pack to the provisioning server.
#For more information, refer to Yealink Auto Provisioning User Guide.
gui_lang.url =
#gui_lang.delete = http://localhost/all, delete all the customized languages.
gui_lang.delete =
#######################################################################################
## Configure the access URL of logo file ##
#######################################################################################
#Before using this parameter, you should store the desired logo file (x.dob) to the provisioning server.
#For more information, refer to Yealink Auto Provisioning User Guide.
lcd_logo.url =
http://172.16.0.88/logo.dob
#lcd_logo.delete = http://localhost/all, delete all the customized logo.
lcd_logo.delete =
#######################################################################################
## Certificates ##
#######################################################################################
#Before using this parameter, you should store the desired certificate to the provisioning server.
trusted_certificates.url =
#trusted_certificates.delete = http://localhost/all,delete all the trusted certificates.
trusted_certificates.delete =
#Before using this parameter, you should store the desired certificate to the provisioning server.
server_certificates.url =
#server_certificates.delete = http://localhost/all, delete the server certificate.
server_certificates.delete =
#The switch of CA cert.0-Defalut£»1-Custom£»2-All(Defalut)
security.ca_cert =
#It configures the device certificates for the phone to send for TLS authentication.
#0-Default certificates,1-Custom certificates.The default value is 0.
#It takes effect after reboot.
security.dev_cert =
#All the TLS application server mandatory verification certificate CommonName or SubjectAltName.0-Disable(Defalut). 1-Enable
security.cn_validation =
#######################################################################################
## Local Contact/DST Time/Dialnow Rule/Replace Rule ##
#######################################################################################
#Before using these parameters, you should store the desired resource files to the provisioning server.
#For more information, refer to Yealink SIP-T2xP IP Phone Family Administrator Guide.
local_contact.data.url =
auto_dst.url =
dialplan_dialnow.url =
dialplan_replace_rule.url =
#######################################################################################
## Customized Factory Configurations ##
#######################################################################################
#Configure the access URL for downloading the customized factory configurations.
#Before using this parameter, you should store the desired factory configuration file to the provisioning server.
custom_factory_configuration.url =
#######################################################################################
## Customized Configurations ##
#######################################################################################
#Configure the access URL for downloading the configurations.
#Before using this parameter, you should store the desired configuration file to the provisioning server.
configuration.url = tftp://172.16.0.88
#It configures the access URL of the customized MAC-Oriented CFG file.
custom_mac_cfg.url = tftp://172.16.0.88
#######################################################################################
## Call List ##
#######################################################################################
#Configure the access URL for downloading the call list.
#Before using this parameter, you should store the desired call list file to the provisioning server.
#Require reboot
call_list.url =
#######################################################################################
## OpenVPN ##
#######################################################################################
#Configure the access URL for downloading the open VPN tar.
#Before using this parameter, you should store the desired VPN file to the provisioning server.
openvpn.url =
#######################################################################################
## Redirect ##
#######################################################################################
#Enable or disable the redirect feature; 0-Disabled (default), 1-Enabled;
redirect.enable =
#######################################################################################
## Configuration files for Var ##
#######################################################################################
#Configure the access URL for downloading the files for var.
#Before using this parameter, you should store the desired files to the provisioning server.
#Require reboot
web_item_level.url =
#Configure the access URL for downloading the files for Search Source List In Dialing.
super_search.url =
#It enables or disables recent call in dialing feature. If it is enabled, you can view the placed calls list when the phone is in the pre-dialing screen(not applicable to the T20P IP phone).
#0-Disabled,1-Enabled,The default value is 0
super_search.recent_call =
#Enable or disable the alert_info. 0-Disabl.1-Enable
features.alert_info_tone =
#Configure the access URL for downloading the files for direcory setting.
directory_setting.url =
#Enable or disable the BroadSoft Directory.
bw_phonebook.personal_enable = 1
bw_phonebook.group_enable = 1
bw_phonebook.enterprise_enable = 0
bw_phonebook.group_common_enable = 0
bw_phonebook.enterprise_common_enable = 0
bw_phonebook.custom = 0
#Configure displayname of the group directory.
bw_phonebook.group_displayname =
#Configure displayname of the enterprise directory.
bw_phonebook.enterprise_displayname =
#Configure displayname of the personal directory.
bw_phonebook.personal_displayname =
##Configure displayname of the group common directory
bw_phonebook.group_common_displayname =
##Configure displayname of the enterprise common directory
bw_phonebook.enterprise_common_displayname =
#Enable or disable the BroadSoft CallLog.1-Enable(Defalut).0-Disable.
bw_phonebook.call_log_enable = 1
#Enable or disable the server search of the Broadsoft Directory.1-Enable£¨Default).0-(Local search).
bw_phonebook.server_search_enable = 1
#Enable or disable the callpark softkey funtion on talking.1-Enable.0-Disable.
call_park.enable = 1
#Enable or disable the Group callpark softkey funtion on talking.1-Enable.0-Disable.
call_park.group_enable =
#Enable or disable the ring notify of park.1-Enable.0-Disable.
call_park.park_ring =
#Enable or disable the visual notify of park.1-Enable.0-Disable.
call_park.park_visual_notify_enable = 1
#####################################################################################
#Enable or disable the group listening in taling. 0-Disable 1-Enable(Default)
features.group_listen_in_talking_enable =
#Configure the priority of auto blflist. 0-linekey,memory,exp£¨Default). 1-exp,memory,linekey.
phone_setting.blf_list_sequence_type =
#Enable or disable auto blf list. 0-Disable 1-Enable(Default)
phone_setting.auto_blf_list_enable =
#Enable or disable the password swith when resetting to factory. 0-Disable(Defalut) 1-Enable.
features.factory_pwd_enable = 0
#Enable or disable reset by long press on OK key. 0-Disable 1-Enable(Defautl)
features.reset_by_long_press_enable =
##Password erase switch of the export config file.0-Encrypted 1-Null(Default)
features.export_cfg_erase_pwd =
Found my issue! I had the setting below set to 1 rather than 0.
From the MAC specific file:
#Enable or disable ACD feature for Account1; 0-Disabled (default), 1-Enabled;
account.1.acd.enable = 1
Thank you for your help.
