T28P idle "login" programmable softkey - Printable Version +- Yealink Forums (http://forum.yealink.com/forum) +-- Forum: IP Phone Series (/forumdisplay.php?fid=4) +--- Forum: Phone specific topic (/forumdisplay.php?fid=12) +---- Forum: T2xP Series (/forumdisplay.php?fid=21) +---- Thread: T28P idle "login" programmable softkey (/showthread.php?tid=893) |
T28P idle "login" programmable softkey - fdtcloud - 10-10-2013 05:11 AM I need to know if I can remove the "Login" programmable softkey from the T28P. I do not use ACD and have specified 4 programmable softkeys I would like displayed, however the Login key gets in the way and forces several keys to the "more" page. RE: T28P idle "login" programmable softkey - Yealink Support - 10-11-2013 02:39 PM Hi Fdtcloud, What's the firmware are you using? You can upgrade to 2.71.0.140, and reset to factory default, there will no "Login" in the softkey. Thanks. RE: T28P idle "login" programmable softkey - fdtcloud - 10-11-2013 10:23 PM I am currently running 2.71.0.140. After factory default I still see the "Login" softkey. I am using auto provisioning, so I suppose my configuration file must have an issue. I will post my y000000000000.cfg and the MAC specific #!version:1.0.0.1 ##File header "#!version:1.0.0.1" can not be edited or deleted, and must be placed in the first line.## ####################################################################################### ## Network ## ####################################################################################### #Configure the duplex mode and the speed of the WAN port. #0-Auto negotiate (default), 1-Full duplex 10Mbps, 2-Full duplex 100Mbps, 3-Half duplex 10Mbps, 4-Half duplex 100Mbps; network.internet_port.speed_duplex = 0 #Configure the username and password for PPPOE connection. #Require reboot; network.pppoe.user = network.pppoe.password = #PC Port Switch.0-Disable 1-Enable(Default) network.pc_port.enable = 1 #Configure the PC port type; 0-Router, 1-Bridge (default); #Require reboot; network.bridge_mode = 1 #Configure the IP address and mask when the PC port is configured as Router. #Require reboot; network.pc_port.ip = 10.0.0.1 network.pc_port.mask = 255.255.255.0 #Configure the duplex mode and the speed of the PC port when configured as Router. #0-Auto negotiate (default), 1-Full duplex 10Mbps, 2-Full duplex 100Mbps, 3-Half duplex 10Mbps, 4-Half duplex 100Mbps; network.pc_port.speed_duplex = 0 #Enable or disable the DHCP server when the PC port is configured as Router; 0-Disabled, 1-Enabled (default); #Require reboot; network.pc_port.dhcp_server = 1 #Define the DHCP IP address range. The default is from 10.0.0.10 to 10.0.0.100. network.dhcp.start_ip = 10.0.0.10 network.dhcp.end_ip = 10.0.0.100 #Enable or disable the VLAN of WAN prot; 0-Disabled (default), 1-Enabled; #Require reboot; network.vlan.internet_port_enable = 0 #Configure the VLAN ID, it ranges from 0 to 4094, the default value is 0. #Require reboot; network.vlan.internet_port_vid = 0 #Configure the VLAN priority, it ranges from 0 (default) to 7. #Require reboot; network.vlan.internet_port_priority = 0 #Enable or disable the VLAN of PC port; 0-Disabled (default), 1-Enabled; #Require reboot; network.vlan.pc_port_enable = 0 #Configure the VLAN ID, it ranges from 0 to 4094, the default value is 1. #Require reboot; network.vlan.pc_port_vid = 1 #Configure the VLAN priority, it ranges from 0 (default) to 7. #Require reboot; network.vlan.pc_port_priority = 0 #Enable or disable the DHCP to obtain the information of the VLAN; 0-Disabled; 1-Enabled (default); #Require reboot; network.vlan.dhcp_enable = 0 #Configure the DHCP option to obtain the information of the VLAN. It ranges from 0 to 255. #Multiple options separated by a comma. It supports up to 5 options in all. #Require reboot; network.vlan.dhcp_option = #Configure the transmit package mode when the VLAN of PC port is enabled; #0-The package is not treated and forwarded directly from PC port to the WAN port; #1-The package is added the tag and forwarded from PC port to the WAN port, if the package is not the tag. #Require reboot; network.vlan.pc_port_mode = 0 #Configure the HTTP port (80 by default) and the HTTPS port (443 by default) of the web server. Both range from 1 to 65535. #Require reboot; network.port.http = 80 network.port.https = 443 #Enable or disable the https access. 1-Enable. 0-Disable. wui.https_enable = 1 wui.http_enable = 1 #Configure the maximum local RTP port. It ranges from 0 to 65535, the default value is 11800. #Require reboot; network.port.max_rtpport = 11800 #Configure the minimum local RTP port. It ranges from 0 to 65535, the default value is 11780. #Require reboot; network.port.min_rtpport = 11780 #Configure the voice QOS. It ranges from 0 to 63, the default value is 46. #Require reboot; network.qos.rtptos = 46 #Configure the SIP QOS. It ranges from 0 to 63, the default value is 26. #Require reboot; network.qos.signaltos = 26 #Configure the 802.1x mode; 0-Disabled (default), 1-EAP-MD5, 2-EAP-TLS, 3-PEAP-MSCHAPV2; #Require reboot; network.802_1x.mode = 0 #Configure the username and password for 802.1x authentication. #Require reboot; network.802_1x.identity = network.802_1x.md5_password = #Configure the access URL of the root and client certificates. network.802_1x.root_cert_url = network.802_1x.client_cert_url = #Enable or disable the VPN feature; 0-Disabled (default), 1-Enabled; #Require reboot; network.vpn_enable = 0 #Enable or disable the LLDP feature; 0-Disabled, 1-Enabled (default); #Require reboot; network.lldp.enable = 1 #Configure the interval(in seconds) the phone broadcasts the LLDP request. It ranges from 1 to 3600, the default value is 60. #Require reboot; network.lldp.packet_interval = 60 #Enable or disable the SNMP feature; 0-Disabled (default), 1-Enabled; #Require reboot; network.snmp.enable = 0 #Configure the SNMP port. #Require reboot; network.snmp.port = #Configure the IP address(es) of the trusted SNMP server,multiple IP addresses must be separated by a space. #Require reboot; network.snmp.trust_ip = #Enable or disable the span from WAN port to PC port feature; 0-Disabled (default), 1-Enabled; #Require reboot; network.span_to_pc_port = 0 #Configure the phone whether to add the MAC address to the User-Agent header; 0-Do not add, 1-Add; #Require reboot; network.sip.tag_mac_to_ua.enable = 0 #It enables or disables the phone to use the static DNS.0-Disabled,1-Enabled,The default value is 0. network.static_dns_enable = 0 ####################################################################################### ## Hostname ## ####################################################################################### #It configures the host name of the phone.The default value is SIP-T2xP (X=0,2,6,8) network.dhcp_host_name = ####################################################################################### ## Syslog Server ## ####################################################################################### #Configure the IP address of the syslog server. #Require reboot; syslog.server = #Configure the syslog type. 0-Local(default), 1-Server. syslog.mode = #Configure the syslog level. It ranges from 0 to 6, the default value is 3. #Require reboot; syslog.log_level = ####################################################################################### ## TR069 ## ####################################################################################### #The TR069 feature is only applicable to some designated firmware version. #All settings of TR069 require reboot. #Enable or disable the TR069 feature; 0-Disabled (default), 1-Enabled; managementserver.enable = 0 #Configure the username and password for the phone to authenticate with the ACS. managementserver.username = managementserver.password = #Configure the access URL of the ACS. managementserver.url = #Configure the username and password for the phone to authenticate the connection requests. managementserver.connection_request_username = managementserver.connection_request_password = #Enable or disable the phone to inform its configuration to the ACS; 0-Disabled (default), 1-Enabled; managementserver.periodic_inform_enable = #Configure the interval (in seconds) the phone to inform its configuration to the ACS. The default value is 60. managementserver.periodic_inform_interval = ####################################################################################### ## Auto Provisioning ## ####################################################################################### #Configure the auto provision mode; #0-Disabled (default), 1-Power on, 4-Repeatedly, 5-Weekly, 6-Power on + Repeatedly, 7-Power on + Weekly; auto_provision.mode = 1 #Enable or disable the Plug and Play feature; 0-Disabled, 1-Enabled (default); auto_provision.pnp_enable = 0 #Configure the domain name of the PNP server. auto_provision.pnp_domain_name = #Configure the value (manufacturer of the device) of the PNP subscribe message. auto_provision.pnp_event_vendor = #Configure the interval (in minutes) for the phone to check new configuration files. It ranges from 1 to 43200, the default value is 1440. #It is only applicable to "Repeatedly" and "Power on + Repeatedly" modes. auto_provision.schedule.periodic_minute = #Configure the start time of the day for the phone to check new configuration files. The default value is 00:00. #It is only applicable to "Weekly" and "Power on + Weekly" modes. #If the desired start time of the day is seven forty-five a.m., the value format is 07:45. auto_provision.schedule.time_from = #Configure the end time of the day for the phone to check new configuration files. The default time is 00:00. #It is only applicable to "Weekly" and "Power on + Weekly" modes. #If the desired end time of the day is seven forty-five p.m., the value format is 19:45. auto_provision.schedule.time_to = #Configure the day of week for the phone to check new configuration files. The default vaule is 0123456. #0-Sunday,1-Monday,2-Tuesday,3-Wednesday,4-Thursday,5-Friday,6-Saturday; #It is only applicable to "Weekly" and "Power on + Weekly" modes. #If the desired week is Monday, Tuesday and Wednesday, the value format is 012. auto_provision.schedule.dayofweek = #Configure the URL of the auto provisioning server. auto_provision.server.url = 172.16.0.88 #Configure the username and password for downloading. auto_provision.server.username = auto_provision.server.password = #Configure the name of the common file. #T28P: y000000000000.cfg, T26P: y000000000004.cfg, T22P: y000000000005.cfg, T20P: y000000000007.cfg; auto_provision.common_file_name = y000000000000.cfg #Enable or disable DHCP option mode; 0-Disabled, 1-Enabled (default); auto_provision.dhcp_option.enable = 1 #Configure the value (manufacturer of the device) of DHCP option 60. auto_provision.dhcp_option.option60_value = #Configure the custom DHCP option number. It ranges from 128 to 254. auto_provision.dhcp_option.list_user_options = 150 auto_provision.aes_key_in_file = #Configure AES key (16 characters) for decrypting the common CFG file. auto_provision.aes_key_16.com = #Configure AES key (16 characters) for decrypting the MAC-Oriented CFG file. auto_provision.aes_key_16.mac = #Configure the mode of downloading configuration files for the phone. The value is 0(default) or 1. auto_provision.update_file_mode = 0 ####################################################################################### ## Auto Provisioning Code ## ####################################################################################### #This feature allows user to trigger the auto provisioning by pressing a predefined string on the phone. #Require reboot; #"X" ranges from 1 to 50 #Configure the auto provisioning name. #The valid value is a string, the maximum length is 100. #autoprovision.X.name = #Configure the auto provisioning code; #The valid value is a string, the maximum length is 100. #autoprovision.X.code = #Configure the URL of the auto provisioning server. #The valid value is a string, the maximum length is 256. #autoprovision.X.url = #Configure the username and password for downloading. #The valid value is a string, the maximum length is 100. #autoprovision.X.user = #autoprovision.X.password = #Configure AES key (16 characters) for decrypting the common CFG file and MAC-Oriented CFG file. #autoprovision.X.com_aes = #autoprovision.X.mac_aes = autoprovision.1.name = Update Configuration autoprovision.1.code = 123456789 autoprovision.1.url = tftp://172.16.0.88 autoprovision.1.user = autoprovision.1.password = autoprovision.1.com_aes = autoprovision.1.mac_aes = autoprovision.2.name = autoprovision.2.code = autoprovision.2.url = autoprovision.2.user = autoprovision.2.password = autoprovision.2.com_aes = autoprovision.2.mac_aes = ####################################################################################### ## Phone Features ## ####################################################################################### #Enable or disable the phone to escape the pound key as percent sign followed by 23 when dialing out; 0-Disabled, 1-Enabled (default); sip.use_23_as_pound = 1 #Enable or disable the RFC2543 Hold feature; 0-Disabled (default), 1-Enabled; sip.rfc2543_hold = 0 #Enable or disable the phone to keep sending the SIP messages to the outbound server; 0-Disabled, 1-Enabled (default); sip.use_out_bound_in_dialog = 1 #Configure the registration random time (in seconds). It ranges from 0 (default) to 60. sip.reg_surge_prevention = 0 #Enable or disable the WatchDog feature; 0-Disabled, 1-Enabled (default); watch_dog.enable = 1 #Enable or disable the transferee to display the missed call prompt when receiving a semi_attended transfer call; #0-Disabled, 1-Enabled (default); transfer.semi_attend_tran_enable = 1 #Enable or disable the phone to complete the blind or attended transfer through on-hook; #0-Disabled,1-Enabled(default); transfer.blind_tran_on_hook_enable = 1 transfer.on_hook_trans_enable = 1 #Define the way of DSS key when configuring as a transfer key; 0-Display Number, 1-Attended Transfer, 2-Blind Transfer (default); transfer.dsskey_deal_type = 2 #Enable or disable the phone to enter the transfer to interface during two calls when pressing the transfer soft key or TRAN key; 0-Disable, 1-Enabled (default); transfer.multi_call_trans_enable = 1 #Enable or disable the conference initiator to transfer the call when hanging up. #0-Disabled(default),1-Enabled; transfer.tran_others_after_conf_enable = 1 ####################################################################################### ## Call Forward ## ####################################################################################### #Configure the call forward key mode; 0-Phone mode (default), 1-Custom mode. features.fwd_mode = 0 #Enable or disable the always forward feature; 0-Disabled (default), 1-Enabled; forward.always.enable = 0 #Configure the target number that the phone will forward the call to. forward.always.target = #Configure the always forward on code and off code. forward.always.on_code = forward.always.off_code = #Enable or disable the busy forward feature; 0-Disabled (default), 1-Enabled; forward.busy.enable = 0 forward.busy.target = forward.busy.on_code = forward.busy.off_code = #Enable or disable the no answer forward feature; 0-Disabled (default), 1-Enabled; #Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 2. forward.no_answer.enable = 0 forward.no_answer.target = forward.no_answer.timeout = forward.no_answer.on_code = forward.no_answer.off_code = #Enable or disable the phone to forward the call to the international number (the prefix is 00); 0-Disabled (default), 1-Enabled; forward.international.enable = ####################################################################################### ## DND ## ####################################################################################### #Configure the DND key mode; 0-Phone mode (default), 1-Custom mode. features.dnd_mode = 0 #Configure the DND on code and off code. features.dnd.on_code = features.dnd.off_code = #It enables or disables the phone to recevice incoming calls from authorized numbers when DND feature is enabled.0-Disabled,1-Enabled.The default value is 0. features.dnd.emergency_enable = 0 #It configures the numbers the phone will receive incoming calls from when DND feature is enabled.Multiple numbers are separated by comma.The default value is blank. features.dnd.emergency_authorized_number = ####################################################################################### ## Voice ## ####################################################################################### #Enable or disable the voice activity detection feature; 0-Disbaled (default), 1-Enabled; voice.vad = 0 #Enable or disable the comfortable noise generator; 0-Disabled, 1-Enabled (default); voice.cng = 1 #Enable or disable the echo canceller; 0-Disabled, 1-Enabled (default); voice.echo_cancellation = 1 #Configure the volume of the side tone. It ranges from -48 to 0, the default value is -3. voice.side_tone= -3 #Configure the sending volume of Speaker, Handset and Headset. It ranges from 1 to 53, the default values are 25, 35, 29. #Require reboot; voice.handfree_send = 25 voice.handset_send = 35 voice.headset_send = 29 #Configure the type of jitter buffer; 0-Fixed, 1-Adaptive (default); voice.jib.adaptive = 1 #Configure the minimum delay, maximum delay and normal delay. The default values are 0, 300, 120. voice.jib.min = 0 voice.jib.max = 300 voice.jib.normal = 120 #Define the voice tone, the valid values can be Custom (default) or voice tone of different countries. For example, United States, France, Germany and so on. #voice.tone.country = Custom voice.tone.country = United States #Customize the tone when the "voice.tone.country" is configured as Custom. #The value format: Frequency/Duration. #Frequency ranges from 200 to 7000. When 0 is used to define the frequency, it means a pause between tones. #A tone can be composited at most four different frequencies (the value format is: F1+F2+F3+F4). #Duration is the time duration (in milliseconds) of ringing the tone. It ranges from 0 to 30000ms. #At most eight tones can be configured for dial, ring, busy and so on, each tone is separated by a comma. #For example, voice.tone.dial = 100/200,200/150,300+400+500+1200/1000,0/1200,500+900/800,5000+2000+3000/6000,0/1500,3600/1800 voice.tone.dial = voice.tone.ring = voice.tone.busy = voice.tone.congestion = voice.tone.callwaiting = voice.tone.dialrecall = voice.tone.record= voice.tone.info = voice.tone.stutter = voice.tone.message = voice.tone.autoanswer = #Configure the receiving volume of Speaker, Handset and Headset. It ranges from 0 to 15, the default value is 8. voice.handfree.spk_vol = 8 voice.handset.spk_vol = 8 voice.headset.spk_vol = 8 #Configure the dial tone volume of Speaker, Handset and Headset. It ranges from 0 to 15, the default value is 8. voice.handfree.tone_vol = 8 voice.handset.tone_vol = 8 voice.headset.tone_vol = 8 #configure the preview call mode; 1-Ignore:the mixed of tone and RTP (default), 2-Force: discard the RTP and play the tone, 3-Skip: skip the tone to play the RTP; voice.call_preview_mode= 1 ####################################################################################### ## Security Settings ## ####################################################################################### #Enable or disable the phone to only accept the certificates in the Trusted Certificates list; #0-Disabled, 1-Enabled (default); security.trust_certificates = #Define the login username and password of the user, var and administrator. #If you change the username of the administrator from "admin" to "admin1", your new administrator's username should be configured as: security.user_name.admin = admin1. #If you change the password of the administrator from "admin" to "admin1pwd", your new administrator's password should be configured as: security.user_password = admin1:admin1pwd. #The following examples change the user's username to "user23" and the user's password to "user23pwd". #security.user_name.user = user23 #security.user_password = user23:user23pwd #The following examples change the var's username to "var55" and the var's password to "var55pwd". #security.user_name.var = var55 #security.user_password = var55:var55pwd security.user_name.user = security.user_name.admin = security.user_name.var = security.user_password = #Enable or disable the 3-level permissions (open var); 0-Disabled (default), 1-Enabled; #Require reboot; security.var_enable = ####################################################################################### ## Customize the softkey ## ####################################################################################### #Customize the softkeys presented on the phone LCD screen when Callfailed, Callin, Connecting, Dialing, Ringback and Talking. #Before using these parameters, you should store the desired XML files to the provisioning server. custom_softkey_call_failed.url = custom_softkey_call_in.url = custom_softkey_connecting.url = custom_softkey_dialing.url = custom_softkey_ring_back.url = custom_softkey_talking.url = ####################################################################################### ## Line Key ## ####################################################################################### #The x of the parameter "linekey.x.line" ranges from 1 to 6. #The default value equals to the value of x. For example, the default value of the parameter "linekey.1.line" is 1. #For T28P, the value of the "linekey.X.line" ranges from 0 to 6. The value 0 or 1 of the "linekey.x.line" stands for line 1£¬The value 2 of the "linekey.x.line" stands for line 2 #linekey.x.lable--Define the label for each line key. #Configure Line Key1 linekey.1.line = 0 linekey.1.value = linekey.1.pickup_value = linekey.1.type = 15 linekey.1.xml_phonebook = linekey.1.label = Ext 1100 #Configure Line Key2 linekey.2.line = 0 linekey.2.value = linekey.2.pickup_value = linekey.2.type = 15 linekey.2.xml_phonebook = linekey.2.label = Ext 1100 #Configure Line Key3 linekey.3.line = 0 linekey.3.value = linekey.3.pickup_value = linekey.3.type = 15 linekey.3.xml_phonebook = linekey.3.label = Ext 1100 #Configure Line Key4 (for T28P only) linekey.4.line = 0 linekey.4.value = linekey.4.pickup_value = linekey.4.type = 15 linekey.4.xml_phonebook = linekey.4.label = Ext 1100 #Configure Line Key5 (for T28P only) linekey.5.line = 0 linekey.5.value = linekey.5.pickup_value = linekey.5.type = 15 linekey.5.xml_phonebook = linekey.5.label = Ext 1100 #Configure Line Key6 (for T28P only) linekey.6.line = 0 linekey.6.value = linekey.6.pickup_value = linekey.6.type = 50 linekey.6.xml_phonebook = linekey.6.label = Lock ########################################################################################## ## Programmable Key ## ########################################################################################## #X ranges from 1 to 15. #programablekey.x.type--Customize the programmable key type. #The valid types are: #0-N/A 2-Forward 5-DND 6-Redial 7-Call Return 8-SMS 9-Direct Pickup 13-Spead Dial #22-XML Group 23-Group Pickup 27-XML Browser 28-History 30-Menu 31-Switch Account 32-New SMS #33-Status 40-PTT 43-Local Phonebook 44-Broadsoft Phonebook 45-Local Group 46-Broadsoft Group 47-XML Phonebook 50-Keypad Lock #55-meet me 56-retrieve park 58-ACD Trace 59-disp code 60-Emergency 61-Directory #PTT-add a specified prefix number before the dialed number. #programablekey.x.line--Configure the desired line to apply the key feature. It ranges from 0 to 6. #The value 0 or 1 of the "proramablekey.x.line" stands for line1, it means the first available line. #programablekey.x.value = #programablekey.x.xml_phonebook--Specify the desired remote phonebook/local group/BSFT phonebook for the programmable key. This parameter is only applicable to the feature XML Group/Local Group/Broadsoft Group. #0-the first phonebook£¬1-the second phonebook£¬and so on. #programablekey.x.history_type = #0-local calllog£¬1-network calllog. #programablekey.x.label--This parameter is only available to the key 1 to key 4. programablekey.1.type = 28 programablekey.1.line = 0 programablekey.1.value = programablekey.1.xml_phonebook = programablekey.1.history_type = programablekey.1.label = History programablekey.2.type = 47 programablekey.2.line = 0 programablekey.2.value = programablekey.2.xml_phonebook = programablekey.2.history_type = programablekey.2.label = Directory programablekey.3.type = 5 programablekey.3.line = 0 programablekey.3.value = programablekey.3.xml_phonebook = programablekey.3.history_type = programablekey.3.label = DND programablekey.4.type = 30 programablekey.4.line = 0 programablekey.4.value = programablekey.4.xml_phonebook = programablekey.4.history_type = programablekey.4.label = Menu ########################################################################################## ## Expansion Key ## ########################################################################################## #X ranges from 1 to 16, Y ranges from 1 to 40. #expansion_module.x.key.y.type = 37 (Switch by default) #expansion_module.x.key.y.line = 0 #expansion_module.x.key.y.value = #expansion_module.x.key.y.pickup_value = #expansion_module.x.key.y.label = #expansion_module.X.key.Y.xml_phonebook = #Each expansion module1 key1 expansion_module.1.key.1.type = 37 expansion_module.1.key.1.line = 0 expansion_module.1.key.1.value = expansion_module.1.key.1.pickup_value = expansion_module.1.key.1.label = Switch expansion_module.1.key.1.xml_phonebook = #Each expansion module1 key2 expansion_module.1.key.2.type = 16 expansion_module.1.key.2.line = 0 expansion_module.1.key.2.value = 102 expansion_module.1.key.2.pickup_value = expansion_module.1.key.2.label = Demo 7945 expansion_module.1.key.2.xml_phonebook = #Each expansion module2 key1 expansion_module.2.key.1.type = 37 expansion_module.2.key.1.line = 0 expansion_module.2.key.1.value = expansion_module.2.key.1.pickup_value = expansion_module.2.key.1.label = Page expansion_module.2.key.1.xml_phonebook = #Each expansion module2 key2 expansion_module.2.key.1.type = 16 expansion_module.2.key.1.line = 0 expansion_module.2.key.1.value = 103 expansion_module.2.key.1.pickup_value = expansion_module.2.key.1.label = Demo 7941 expansion_module.2.key.1.xml_phonebook = ####################################################################################### ## Automatic Call Distribute ## ####################################################################################### #Enable or disable the phone to automatically change the phone status to available; 0-Disabled (default), 1-Enabled; acd.auto_available = #Configure the interval (in seconds) to automatically turn the state of the ACD agent to available. It ranges from 0 to 120, the default value is 60. acd.auto_available_timer = ####################################################################################### # Action URL Settings ## ####################################################################################### #action_url.setup_completed--Inform the server that the phone has completed the startup. #action_url.dnd_on-- Inform the server that the DND is activated on the phone. #The value format is: http://IP address of server/help.xml?variable name=variable value. #The valid variable values are: $mac--MAC address of phone, $ip--The current IP address of phone, $model--Phone model, $firmware--Phone firmware version. #$active_url--The SIP URI of the current account when the phone is in the incoming state, outgoing state or during conversation. #$active_user--The username of the current account when the phone is in the incoming state, outgoing state or during conversation. #$active_host--The host name of the current account when the phone is in the incoming state, the outgoing state or during conversation. #$local--The SIP URI of the caller when outgoing calls or the SIP URI of the callee when receiving calls. #$remote--The SIP URI of the callee when outgoing calls or the SIP URI of the caller when receiving calls. #$display_local--The display name of the caller when outgoing calls or the display name of the callee when receiving calls. #$display_remote--The display name of the callee when outgoing calls or the display name of the caller when receiving calls. #$call_id--The caller ID when in the incoming state, the outgoing state or during conversation. #For example, action_url.log_on = http://192.168.1.20/help.xml?mac=$mac action_url.setup_completed = action_url.log_on = action_url.log_off = action_url.register_failed = action_url.off_hook = action_url.on_hook = action_url.incoming_call = action_url.outgoing_call = action_url.call_established = action_url.dnd_on = action_url.dnd_off = action_url.always_fwd_on = action_url.always_fwd_off = action_url.busy_fwd_on = action_url.busy_fwd_off = action_url.no_answer_fwd_on = action_url.no_answer_fwd_off = action_url.transfer_call = action_url.blind_transfer_call = action_url.attended_transfer_call = action_url.hold = action_url.unhold = action_url.mute = action_url.unmute = action_url.missed_call = action_url.call_terminated = action_url.busy_to_idle = action_url.idle_to_busy = action_url.ip_change = action_url.answer_new_incoming_call = action_url.reject_incoming_call = action_url.transfer_finished = action_url.transfer_failed = action_url.forward_incoming_call = ####################################################################################### ## Language Settings ## ####################################################################################### #Specify the web language, the valid values are: English, Chinese_S, Turkish, Portuguese, Spanish, Italian, French, Russian, Deutsch and Czech. lang.wui = English #Specify the LCD language, the valid values are: English (default), German, French, Turkish, Italian, Polish, Spanish and Portuguese. #lang.gui = English lang.gui = English ####################################################################################### ## Time Settings ## ####################################################################################### #Configure the time zone and time zone name. The time zone ranges from -11 to +12, the default value is +8. #The default time zone name is China(Beijing). #Refer to Yealink IP Phones User Guide for more available time zones and time zone names. #local_time.time_zone = +8 #local_time.time_zone_name = China(Beijing) local_time.time_zone = -7 local_time.time_zone_name = Mountain #Configure the domain name or the IP address of the NTP server. The default value is cn.pool.ntp.org. local_time.ntp_server1 = 66.60.100.1 local_time.ntp_server2 = pool.ntp.org #Configure the update interval (in seconds) when using the NTP server. The default value is 1000. local_time.interval = 1000 #Configure the daylight saving time feature; 0-Disabled, 1-Enabled, 2-Automatic (default); local_time.summer_time = 2 #Configure the DST type when the DST feature is enabled; 0-By Date (default), 1-By Week; local_time.dst_time_type = #Configure the start time of DST. The default value is 1/1/0. #If the DST type is configured as By Date, the value format is Month/Day/Hour. For example, the value 5/20/10 means the start time is at 10:00 on May 20. #If the DST type is configured as By Week, the value format is Month/Day of Week/Day of Week Last in Month/Hour of Day. #For example, the value 1/4/2/5 means the start time is at 5 o'clock on Tuesday of the 4th week in January. local_time.start_time = #Configure the end time of DST. The default value is 12/31/23. The value format is the same to the start time. local_time.end_time = #Configure the offset time (in seconds). It ranges from -300 to 300, the default value is 60. local_time.offset_time = #Configure the time format; 0-12 Hour, 1-24 Hour (default); local_time.time_format = #Configure the date format; 0-WWW MMM DD (default), 1-DD-MMM-YY, 2-YYYY-MM-DD, 3-DD/MM/YYYY, 4-MM/DD/YY, 5-DD MMM YYYY, 6-WWW DD MMM; local_time.date_format = #Enable or disable the DHCP Time; 0-Disabled (default), 1-Enabled; local_time.dhcp_time = #Enable or disable the manual time setting. 0-Disabled (default), 1-Enabled; local_time.manual_time_enable = ####################################################################################### ## Hot Desking ## ####################################################################################### #Enable or disable the phone to show the following items on the login wizard during startup; 0-Disabled, 1-Enabled; #hotdesking.startup_register_name_enable = 1 (default) #hotdesking.startup_username_enable = 1 (default) #hotdesking.startup_password_enable = 0 (default) #hotdesking.startup_sip_server_enable = 0 (default) #hotdesking.startup_outbound_enable = 0 (default) hotdesking.startup_register_name_enable = 0 hotdesking.startup_username_enable = 0 hotdesking.startup_password_enable = 0 hotdesking.startup_sip_server_enable = 0 hotdesking.startup_outbound_enable = 0 #Enable or disable the phone to show the following items on the login wizard when pressing the Hot Desking DSS key; #0-Disabled, 1-Enabled; #hotdesking.dsskey_register_name_enable = 1 (default) #hotdesking.dsskey_username_enable = 1 (default) #hotdesking.dsskey_password_enable = 0 (default) #hotdesking.dsskey_sip_server_enable = 0 (default) #hotdesking.dsskey_outbound_enable = 0 (default) hotdesking.dsskey_register_name_enable = 0 hotdesking.dsskey_username_enable = 0 hotdesking.dsskey_password_enable = 0 hotdesking.dsskey_sip_server_enable = 0 hotdesking.dsskey_outbound_enable = 0 ####################################################################################### ## Distinctive Ring Tones ## ####################################################################################### #"X" ranges from 1 to 10; #Configure the text to map the keywords contained in the "Alert-info" header. #distinctive_ring_tones.alert_info.X.text = family distinctive_ring_tones.alert_info.1.text = #Specify the ring tone for each text. It ranges from 1 to 8. The default value 1 stands for Ring1.wav. #1-Ring1.wav, 2-Ring2.wav, 3-Ring3.wav, 4-Ring4.wav, 5-Ring5.wav, 6-Ring6.wav, 7-Ring7.wav, 8-Ring8.wav. #distinctive_ring_tones.alert_info.X.ringer = 1 distinctive_ring_tones.alert_info.1.ringer = ####################################################################################### ## Auto Redial ## ####################################################################################### #Enable or disable the auto redial feature; 0-Disabled (default), 1-Enabled; auto_redial.enable = #Configure the interval (in seconds) to wait before redial. It ranges from 1 to 300. The default value is 10. auto_redial.interval = #Configure the auto redial times. It ranges from 1 to 300. The default value is 10. auto_redial.times = ####################################################################################### ## Zero Touch ## ####################################################################################### #Enable or disable the Zero Touch feature; 0-Disabled (default), 1-Enabled; zero_touch.enable = #Configure the waiting time (in seconds) before canceling the Zero Touch. It ranges from 0 to 100, the default value is 5. zero_touch.wait_time = ####################################################################################### ## Push XML ## ####################################################################################### push_xml.server = #Enable or disable the phone to display the push XML interface when receiving an incoming call; 0-Disabled (default), 1-Enabled; push_xml.block_in_calling = #Enable or disable the phone to use the push XML via SIP Notify message; 0-Disabled (default), 1-Enabled; push_xml.sip_notify = ####################################################################################### ## Dial Plan ## ####################################################################################### #Configure the area code; dialplan.area_code.code = dialplan.area_code.min_len = 1 dialplan.area_code.max_len = 15 #When applying the rule to multiple lines, each line ID separated by a comma. #e.g. dialplan.area_code.line_id = 1,2,3 dialplan.area_code.line_id = #Configure the block out number. X ranges from 1 to 10. #dialplan.block_out.number.x = dialplan.block_out.number.1 = #When applying the rule to multiple lines, mutiple lines must be separated by a comma. E.g. 1,2,3. #dialplan.block_out.line_id.X = dialplan.block_out.line_id.1 = #Configure the replace rule. X ranges from 1 to 20. #dialplan.item.X = Enabled,Prefix,Replaced,LineID #Enabled: Enable or disable the replace rule. 0-Disabled, 1-Enabled; Prefix: Specify the numbers that need replacing; #Replaced: Specify the alternate numbers; #LineID: Specify the line ID to apply the replace rule,multiple lines ID must be separated by a comma; dialplan.item.1 = #Configure the dialnow rule. X ranges from 1 to 20. #dialnow.item.X = Dial-now rule,Line ID #Dial-now rule: Specify the numbers that need replacing; #Line ID:Specify the line ID to apply the replace rule,multiple lines must be separated by a comma; dialnow.item.1 = dialplan.dialnow.rule.X = dialplan.dialnow.line_id.X = dialplan.replace.prefix.X = dialplan.replace.replace.X = dialplan.replace.line_id.X = ####################################################################################### ## BSFT Phonebook ## ####################################################################################### #Configuration of BW phonebook. X ranges from 1 to 6. #bw_phonebook.data.X.server = #bw_phonebook.data.X.port = #bw_phonebook.data.X.username = #bw_phonebook.data.X.password = #bw_phonebook.data.X.name = bw_phonebook.data.1.server = bw_phonebook.data.1.port = bw_phonebook.data.1.username = bw_phonebook.data.1.password = bw_phonebook.data.1.name = #Configure the search parameter of Broadsoft phonebook version 1.0, mutiple parameters must be separated by a "&"symbol. bw_phonebook.search_params_v1 = #Configure the search parameter of Broadsoft phonebook version 2.0, mutiple parameters must be separated by a "&"symbol. bw_phonebook.search_params_v2 = #Configure the mode of search parameters; 0-AND, 1-OR (default); The vaule only works in Broadsoft phonebook verion 2.0; bw_phonebook.search_mode_or = ####################################################################################### ## BSFT Call Log ## ####################################################################################### #Configuration of the BW call log. X ranges from 1 to 3. #bw_call_log.data.X.server = #bw_call_log.data.X.port = #bw_call_log.data.X.username = #bw_call_log.data.X.password = #bw_call_log.data.X.name = bw_call_log.data.1.server = bw_call_log.data.1.port = bw_call_log.data.1.username = bw_call_log.data.1.password = bw_call_log.data.1.name = #Enable or disable the phone to access the BSFT call log/phonebook directly when pressing the History/Directory soft keys; #0-Disabled (default), 1-Enabled; #Require reboot; bw.calllog_and_dir = #Specify whether to display the BSFT call log on the web user interface; 0-Disabled, 1-Enabled (default); #Require reboot; bw.behave_calllog = #Specify whether to display the BSFT directory on the web user interface; 0-Disabled, 1-Enable (default); #Require reboot; bw.directory_enable = #Enable or disable the feature key synchronization; 0-Disabled (default), 1-Enabled; bw.feature_key_sync = ####################################################################################### ## Remote phonebook ## ####################################################################################### #Configure the access URL and dispaly name of the remote phonebook. X ranges from 1 to 5. #remote_phonebook.data.X.url = #remote_phonebook.data.X.name = remote_phonebook.data.1.url = http://172.16.0.88/ciscodirectory.xml remote_phonebook.data.1.name = Company Directory ####################################################################################### ## LDAP Settings ## ####################################################################################### #Configure the search criteria for name and number lookups. ldap.name_filter = ldap.number_filter = ldap.host = 0.0.0.0 ldap.port = 389 ldap.base = ldap.user = ldap.password = #Specify the maximum of the displayed search results. It ranges from 1 to 32000, the default value is 50. ldap.max_hits = ldap.name_attr = ldap.numb_attr = ldap.display_name = #Configure the LDAP version. The valid value is 2 or 3 (default). ldap.version = #Conifugre the search delay time. It ranges from 0 (default) to 2000. ldap.search_delay = #Enable or disable the phone to query the contact name from the LDAP server when receiving an incoming call; 0-Disabled (default), 1-Enabled; ldap.call_in_lookup = #Enable or disable the phone to sort the search results in alphabetical order; 0-Disabled (default), 1-Enabled; ldap.ldap_sort = #Enable or disable the phone to query the LDAP server when in the pre-dialing or the dialing state; 0-Disabled (default), 1-Enabled; ldap.dial_lookup = ####################################################################################### ## Phone Features ## ####################################################################################### #Configure the return code when activating DND; 404-No Found, 480-Temporarily not available (default), 486-Busy here; #features.dnd_refuse_code = 480 features.dnd_refuse_code = #Configure the return code when refusing a call. The valid values are 404, 480, 486 (default). features.normal_refuse_code = #Enable or disable the call completion feature; 0-Disabled (default), 1-Enabled; features.call_completion_enable = #Configure the LED flashing mode of the BLF key (line key). The value is 0(default) or 1. features.blf_led_mode = #Enable or disable the call waiting feature; 0-Disabled, 1-Enabled (default); call_waiting.enable = #It configures the call waiting on code.The default value is blank. call_waiting.on_code = #It configures the call waiting off code.The default value is blank. call_waiting.off_code = #Enable or disable the playing of call waiting tone; 0-Disabled, 1-Enabled (default); call_waiting.tone = #Enable or disable the intercom feature; 0-Disabled, 1-Enabled (default); features.intercom.allow = #Enable or disable the phone to mute the Speaker when answering an intercom call; 0-Disabled (default), 1-Enabled; features.intercom.mute = #Enable or disable the phone to play the intercom warning tone; 0-Disabled, 1-Enabled (default); features.intercom.tone = #Enable or disable the phone to barge in an intercom call; 0-Disabled (default), 1-Enabled; features.intercom.barge = #Enables or disables the IP phone to query the contact names from the remote phonebook when receiving incoming calls; 0-Disabled (default), 1-Enabled; features.remote_phonebook.enable = #Set the interval (in seconds) for the phone to update the information of the remote phonebook. The default value is 21600. features.remote_phonebook.flash_time = #Configure the hotline number and delay time (in seconds). It ranges from 0 to 180, the default value is 4. features.hotline_number = features.hotline_delay = #Enable or disable the phone to suppress the display of DTMF digits; 0-Disabled (default), 1-Enabled; features.dtmf.hide = #Enables or disables the IP phone to display the DTMF digits for a short period before displaying as asterisks; 0-Disabled (default), 1-Enabled; features.dtmf.hide_delay = #Configure the repetition times of DTMF end packet. The valid values are 1, 2, 3 (default). features.dtmf.repetition = #Configure DTMF sequences. It can be consisted of digits, alphabets, * and #. features.dtmf.transfer = #Enable or disable the phone to send DTMF sequences during a call when pressing the transfer soft key or the TRAN key; 0-Disabled (default), 1-Enabled; features.dtmf.replace_tran = #Enable or disable the headset prior feature; 0-Disabled (default), 1-Enabled; features.headset_prior = #Enable or disable the dual headset feature; 0-Disabled (default), 1-Enabled; features.headset_training = #Configure the delay time (in milliseconds) before transfering a call. The default value is 0. features.hold_trans_delay = #Enbale or disable the phone to play a local DTMF tone; 0-Disabled, 1-Enabled (default); features.play_local_dtmf_tone_enable = #Enbale or disable the server to release the BLA line automatically; 0-Disabled (default), 1-Enabled; features.auto_release_bla_line = #Configure the delay time (in seconds) of playing busy tone when rejecting a call. The valid values are 0 (default), 3 and 5. features.busy_tone_delay = #Configure the phone whether to send a pound key when pressing double pound keys; 0-Send one pound key (default), 1-Do not send any pound key; features.send_pound_key = #Define the "#" or "*" key as the send key; 0-Disabled, 1-# key(default), 2-* key; features.pound_key.mode = #Enable or disable the phone to play tone when pressing the digit key; 0-Disabled, 1-Enabled (default); features.send_key_tone = features.key_tone = #Enable or disable the phone to play a warning tone when there is a held call; 0-Disabled, 1-Enabled (default); features.play_hold_tone.enable = #Configure the interval of playing a warning tone. The default value is 30s. features.play_hold_tone.delay = features.redial_tone = #Enable or disable the phone with active accounts to play tones in the dialing interface differently from the phone with no active accounts; 0-Disabled (default), 1-Enbaled; features.partition_tone = #Enable or disable the phone to encrypt the digits of the dialed number. The encrypted digits are displayed as asterisks on the LCD screen; 0-Disabled (default), 1-Enabled; features.password_dial.enable = #Configure the prefix numbers displayed before the encrypted digits. features.password_dial.prefix = #Configure the length of encrypted digits. features.password_dial.length = #Enable or disable the phone to diaplay the Save Call Log option on the web user interface; 0-Disabled, 1-Enabled (default); features.history_save_display = #Enable or disable the phone to save the call history; 0-Disabled, 1-Enabled (default); features.save_call_history = #Configure the power Indicator LED to turn on ro turn off; 0-On (default), 1-Off; features.power_led_on = #Specifie the address(es) or enters ¡°any¡± from which Action URI will be accepted. #For discontinuous IP addresses, each IP address is separated by comma, for example: 192.168.1.20,10.2.1.30 #For continuous IP addresses, the format likes *.*.*.* and the ¡°*¡± stands for the values 0~255. For example: 10.10.*.* stands for the IP addresses that range from 10.10.0.0~10.10.255.255. #If left blank, the IP phone cannot receive or handle any HTTP GET request. #If set to ¡°any¡±, the IP phone accepts and handles HTTP GET requests from any IP address. features.action_uri_limit_ip = #Configure the delay time (in seconds)of auto answer. The time ranges from 1 to 4, the default value is 1s. features.auto_answer_delay = #Enable or disable the transfer DSS key to perform the blind transfer; 0-Disabled, 1-Enabled (default); features.dsskey_blind_tran = #Configure the overtime (in minutes) of logging web user interface. It ranges from 1 to 1000, the default value is 5. features.relog_offtime = #Enable or disable the phone to dial the IP address directly; 0-Disabled, 1-Enabled (default); features.direct_ip_call_enable = #Configure the ringtone of emergency calls; #features.emergency_ring = Emergency.wav features.emergency_ring = #Enable or disable the phone to mute the call during an active call; 0-Disabled, 1-Enabled (default); features.allow_mute = #Specify the ring device when the phone is in the Headset mode; 0-use Speaker (default), 1-use Headset;2- Use Headset& Speaker. features.ringer_device.is_use_headset = #Enable or disable the phone to pick up the call using the group pickup soft key; 0-Disabled (default), 1-Enabled; features.pickup.group_pickup_enable = #Configure the group pickup code. features.pickup.group_pickup_code = #Enable or disable the phone to pick up the call using the directed pickup soft key; 0-Disabled (default), 1-Enabled; features.pickup.direct_pickup_enable = #Configure the directed pickup code. features.pickup.direct_pickup_code = ** #Specify the way to notify the phone of the incoming call of the monitored user by visual or audio indicator; #0-Disabled (default), 1-Enabled; features.pickup.blf_visual_enable = features.pickup.blf_audio_enable = #Configure the input type when the phone is in the dialing state, if the parameter "ldap.dial_lookup" is Enabled; 0-2aB, 1-123 (default), 2-abc, 3-ABC; features.ldap.input_type = #Enable or disable the phone to play the warning tone when receiving a vocie mail. 0-Disabled; 1-Enabled(default). features.voice_mail_tone_enable = #Blf led switch in idle.0-Disabled; 1-Enabled(default). features.blf_and_callpark_idle_led_enable = #Forward Diversion switch. 0-Disabled(default); 1-Enabled features.fwd_diversion_enable = #Configure the time (in seconds) the phone automatically dials out the dialed digits. It ranges from 1 to 14, the default value is 4. phone_setting.inter_digit_time = #Configure the flash hook time (in milliseconds). It ranges from 0 to 799, the default value is 1. phone_setting.flash_hook_timer = #Configure the keypad lock type; 0-Disabled (default), 1-Menu Key, 2-Function Key, 3-All Keys, 4-Lock&Answer; phone_setting.lock = #Configure the unlock password for the phone. The default value is 123. phone_setting.phone_lock.unlock_pin = #Configures the interval (in seconds) to automatically lock the IP phone. It ranges from 0 to 3600, the default value is 0. phone_setting.phone_lock.lock_time_out = #Configure the ring tone for the phone. System ring tones are: Common, Ring1.wav (default), Ring2.wav¡Â¡ÂRing8.wav. #If you set the custom ring tone (Busy.wav) for the phone, the value is: phone_setting.ring_type = Busy.wav #If you set the system ring tone (Ring2.wav) for the phone, the value is: phone_setting.ring_type = Ring2.wav phone_setting.ring_type = #Configure the contrast of the LCD screen. It ranges from 1 to 10,the default value is 6. phone_setting.contrast = #Configure the logo mode of the LCD screen; 0-Disabled (default), 1-System logo, 2-Custom logo; phone_setting.lcd_logo.mode = 2 #Configure the active backlight level. It ranges from 1 to 3, the default value is 2. #The same level for different phones may result in different backlight intensities. phone_setting.active_backlight_level = #Configure the backlight time (in seconds). The valid values are: 0-Always on, 1-Always off, 15-15s, 30-30s (default), 60-60s, 120-120s. phone_setting.backlight_time = #Configure the ring tone when the transfer fails. The valid values are: Ring1.wav.... Ring8.wav. #phone_setting.ring_for_tranfailed = Ring1.wav phone_setting.ring_for_tranfailed = #Enable or disable the phone to show the logon wizard during startup; 0-Disabled (default), 1-Enabled; phone_setting.logon_wizard = #Enable or disable the phone to automatically dial out the dialed digits in the pre-dial interface; 0-Disabled (default), 1-Enabled; phone_setting.predial_autodial = #Enable or disable the phone to deal the 180 SIP message after the 183 SIP message; 0-Disabled, 1-Enabled (default); phone_setting.is_deal180 = #Configure the delay time (in seconds) for the dialnow rule. It ranges from 1 to 14, the default value is 1. phone_setting.dialnow_delay = #Enable or disable customizing the softkey layout; 0-Disabled (default), 1-Enabled; phone_setting.custom_softkey_enable = #Configure the using mode of the headset key. The value is 0 or 1(default). phone_setting.headsetkey_mode = #Configure the emergency number, each separated by a comma. The default value is 112,911,110. phone_setting.emergency.number = #Configure the phone whether to end the call when the network is unavailable; 0-End the call, 1-Do not end the call. phone_setting.end_call_net_disconnect.enable = #If leaving the field blank, the phone will display the value sent from the server when receiveing the 403 message; otherwise display the value entered in the filed. #The default value is blank. phone_setting.show_code403 = #It configures a text logo.The maximum length of the value is 15 characters(only applicable to T20P IP phone).The default value is Yealink. phone_setting.lcd_logo.text = ####################################################################################### ## Multicast ## ####################################################################################### #Configure the codec of multicast paging. multicast.codec = #Enbale or diable the phone to handle the incoming multicast paging calls when there is a multicast paging call on the phone; 0-Disabled, 1-Enabled (default); #If enabled, the phone will answer the incoming multicast paging call with a higher priority and ignore that with a lower priority. multicast.receive_priority.enable = #Configure the priority of multicast paging calls. It ranges from 0 to 10. multicast.receive_priority.priority = #Configure the listening multicast IP address and port number for the phone. X ranges from 1 to 10. #multicast.listen_address.X.ip_address = multicast.listen_address.1.ip_address = #Configure the lable displayed on the LCD screen when receiving the multicast paging. X ranges from 1 to 10. #multicast.listen_address.X.label = multicast.listen_address.1.label = ####################################################################################### ## Configure the access URL of firmware ## ####################################################################################### #Before using this parameter, you should store the desired firmware (x.70.x.x.rom) to the provisioning server. firmware.url = tftp://172.16.0.88/2.71.0.140.rom ####################################################################################### ## Configure the access URL of the customized ringtones ## ####################################################################################### #Before using this parameter, you should store the desired ring tone (x.wav) to the provisioning server. #For more information, refer to Yealink Auto Provisioning User Guide. ringtone.url = #ringtone.delete = http://localhost/all,delete all the customized ring tones. ringtone.delete = ####################################################################################### ## Configure the access URL of language file ## ####################################################################################### #Before using this parameter, you should store the desired language pack to the provisioning server. #For more information, refer to Yealink Auto Provisioning User Guide. gui_lang.url = #gui_lang.delete = http://localhost/all, delete all the customized languages. gui_lang.delete = ####################################################################################### ## Configure the access URL of logo file ## ####################################################################################### #Before using this parameter, you should store the desired logo file (x.dob) to the provisioning server. #For more information, refer to Yealink Auto Provisioning User Guide. lcd_logo.url = http://172.16.0.88/logo.dob #lcd_logo.delete = http://localhost/all, delete all the customized logo. lcd_logo.delete = ####################################################################################### ## Certificates ## ####################################################################################### #Before using this parameter, you should store the desired certificate to the provisioning server. trusted_certificates.url = #trusted_certificates.delete = http://localhost/all,delete all the trusted certificates. trusted_certificates.delete = #Before using this parameter, you should store the desired certificate to the provisioning server. server_certificates.url = #server_certificates.delete = http://localhost/all, delete the server certificate. server_certificates.delete = #The switch of CA cert.0-Defalut£»1-Custom£»2-All(Defalut) security.ca_cert = #It configures the device certificates for the phone to send for TLS authentication. #0-Default certificates,1-Custom certificates.The default value is 0. #It takes effect after reboot. security.dev_cert = #All the TLS application server mandatory verification certificate CommonName or SubjectAltName.0-Disable(Defalut). 1-Enable security.cn_validation = ####################################################################################### ## Local Contact/DST Time/Dialnow Rule/Replace Rule ## ####################################################################################### #Before using these parameters, you should store the desired resource files to the provisioning server. #For more information, refer to Yealink SIP-T2xP IP Phone Family Administrator Guide. local_contact.data.url = auto_dst.url = dialplan_dialnow.url = dialplan_replace_rule.url = ####################################################################################### ## Customized Factory Configurations ## ####################################################################################### #Configure the access URL for downloading the customized factory configurations. #Before using this parameter, you should store the desired factory configuration file to the provisioning server. custom_factory_configuration.url = ####################################################################################### ## Customized Configurations ## ####################################################################################### #Configure the access URL for downloading the configurations. #Before using this parameter, you should store the desired configuration file to the provisioning server. configuration.url = tftp://172.16.0.88 #It configures the access URL of the customized MAC-Oriented CFG file. custom_mac_cfg.url = tftp://172.16.0.88 ####################################################################################### ## Call List ## ####################################################################################### #Configure the access URL for downloading the call list. #Before using this parameter, you should store the desired call list file to the provisioning server. #Require reboot call_list.url = ####################################################################################### ## OpenVPN ## ####################################################################################### #Configure the access URL for downloading the open VPN tar. #Before using this parameter, you should store the desired VPN file to the provisioning server. openvpn.url = ####################################################################################### ## Redirect ## ####################################################################################### #Enable or disable the redirect feature; 0-Disabled (default), 1-Enabled; redirect.enable = ####################################################################################### ## Configuration files for Var ## ####################################################################################### #Configure the access URL for downloading the files for var. #Before using this parameter, you should store the desired files to the provisioning server. #Require reboot web_item_level.url = #Configure the access URL for downloading the files for Search Source List In Dialing. super_search.url = #It enables or disables recent call in dialing feature. If it is enabled, you can view the placed calls list when the phone is in the pre-dialing screen(not applicable to the T20P IP phone). #0-Disabled,1-Enabled,The default value is 0 super_search.recent_call = #Enable or disable the alert_info. 0-Disabl.1-Enable features.alert_info_tone = #Configure the access URL for downloading the files for direcory setting. directory_setting.url = #Enable or disable the BroadSoft Directory. bw_phonebook.personal_enable = 1 bw_phonebook.group_enable = 1 bw_phonebook.enterprise_enable = 0 bw_phonebook.group_common_enable = 0 bw_phonebook.enterprise_common_enable = 0 bw_phonebook.custom = 0 #Configure displayname of the group directory. bw_phonebook.group_displayname = #Configure displayname of the enterprise directory. bw_phonebook.enterprise_displayname = #Configure displayname of the personal directory. bw_phonebook.personal_displayname = ##Configure displayname of the group common directory bw_phonebook.group_common_displayname = ##Configure displayname of the enterprise common directory bw_phonebook.enterprise_common_displayname = #Enable or disable the BroadSoft CallLog.1-Enable(Defalut).0-Disable. bw_phonebook.call_log_enable = 1 #Enable or disable the server search of the Broadsoft Directory.1-Enable£¨Default).0-(Local search). bw_phonebook.server_search_enable = 1 #Enable or disable the callpark softkey funtion on talking.1-Enable.0-Disable. call_park.enable = 1 #Enable or disable the Group callpark softkey funtion on talking.1-Enable.0-Disable. call_park.group_enable = #Enable or disable the ring notify of park.1-Enable.0-Disable. call_park.park_ring = #Enable or disable the visual notify of park.1-Enable.0-Disable. call_park.park_visual_notify_enable = 1 ##################################################################################### #Enable or disable the group listening in taling. 0-Disable 1-Enable(Default) features.group_listen_in_talking_enable = #Configure the priority of auto blflist. 0-linekey,memory,exp£¨Default). 1-exp,memory,linekey. phone_setting.blf_list_sequence_type = #Enable or disable auto blf list. 0-Disable 1-Enable(Default) phone_setting.auto_blf_list_enable = #Enable or disable the password swith when resetting to factory. 0-Disable(Defalut) 1-Enable. features.factory_pwd_enable = 0 #Enable or disable reset by long press on OK key. 0-Disable 1-Enable(Defautl) features.reset_by_long_press_enable = ##Password erase switch of the export config file.0-Encrypted 1-Null(Default) features.export_cfg_erase_pwd = Found my issue! I had the setting below set to 1 rather than 0. From the MAC specific file: #Enable or disable ACD feature for Account1; 0-Disabled (default), 1-Enabled; account.1.acd.enable = 1 Thank you for your help. RE: T28P idle "login" programmable softkey - Yealink Support - 10-14-2013 09:51 AM Hi Fdtcloud, Thank you for your reply. We will continue to render our service for you if you have other question. Best Regards |