[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Failover and register on enable config
Author Message
jmpg Offline
Junior Member
**

Posts: 5
Joined: Jul 2015
Reputation: 0
Post: #1
Failover and register on enable config
Hi,

I'm testing the T21P E2 with firmware 52.80.0.70 in failover scenarios.
I've the following configuration set;

account.1.sip_server.1.address = <my_domain_name>
account.1.sip_server.1.port = 0
account.1.sip_server.1.transport_type = 3
account.1.sip_server.1.expires = 180
account.1.sip_server.1.failback_mode = 2
account.1.sip_server.1.register_on_enable = 1

I was expecting that with this configuration set, when I try to call some other extension just after a primary server failure the phone would register to the secondary server prior to make the call, but that is not happening! The phone only sends an INVITE to the secondary server. Only after expiring half the registry expire time (90 secs in my setup) the phone will register with the secondary server. Is this a FW bug, or am I doing some config wrong?

Best regards,
José Gonçalves
(This post was last modified: 10-21-2015 06:24 PM by jmpg.)
10-21-2015 02:32 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink_Michael Offline
Administrator
*******

Posts: 382
Joined: Jul 2015
Reputation: 2
Post: #2
RE: Failover and register on enable config
hello Jose

thanks for your information

for the Expires(30~7200s) of sip server , it is set by design as below :

30<X<1200, 2/x to register
X>1200, X-600 to register

so when you set 180, phone will re-register every 90 seconds, it is normal , not a bug

TKS & BR

Michael
10-21-2015 06:10 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jmpg Offline
Junior Member
**

Posts: 5
Joined: Jul 2015
Reputation: 0
Post: #3
RE: Failover and register on enable config
(10-21-2015 06:10 AM)Yealink_Michael Wrote:  hello Jose

thanks for your information

for the Expires(30~7200s) of sip server , it is set by design as below :

30<X<1200, 2/x to register
X>1200, X-600 to register

so when you set 180, phone will re-register every 90 seconds, it is normal , not a bug

TKS & BR

Michael

Michael,

My issue is not related with the register expire timeout, but with the phone not trying to send a REGISTER packet to the secondary server just after there is a failover condition, i.e., after there is no reply to the INVITE packets send to the primary server and when the config variable account.1.sip_server.1.register_on_enable is set to 1. When this config variable is set to 1 the phone should not register immediately to the secondary server on a failover condition?

Regards,
José Gonçalves
(This post was last modified: 10-21-2015 09:11 AM by jmpg.)
10-21-2015 09:11 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jmpg Offline
Junior Member
**

Posts: 5
Joined: Jul 2015
Reputation: 0
Post: #4
RE: Failover and register on enable config
Can you tell me what the variable "account.1.sip_server.1.register_on_enable" is supposed to change in the phone behaviour?
(This post was last modified: 10-27-2015 08:56 PM by jmpg.)
10-27-2015 08:55 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  T26P failed to register with TLS transport tvt 0 4,118 10-29-2021 02:58 PM
Last Post: tvt
Smile Can a T29G Config.bin file be uploaded into a T23G Red Stone Telecom 0 5,073 03-29-2020 08:35 PM
Last Post: Red Stone Telecom
  T21P Register Failed agatospk 6 20,855 01-31-2020 06:08 AM
Last Post: agatospk
  T22p does not get IP, and does not access the web interface even by manually config jason.luka 5 14,914 04-18-2018 01:29 AM
Last Post: anonymous1718628087441
  T21P E2 can't register(stuck at Registering ..) myombo 1 9,250 11-05-2015 05:25 AM
Last Post: Yealink_Michael
  T28P won't download all config files anais.morales 1 7,116 08-14-2015 06:12 PM
Last Post: Yealink_Michael
  T20P Register Fail on Reboot amirscei 2 9,859 08-06-2015 07:07 AM
Last Post: amirscei
  Register Failed on T22P to MyPBX U100 Firewall 3 12,865 07-14-2015 11:36 AM
Last Post: Firewall
  T20 try to register on 5062 port mikelharris 1 7,986 06-18-2015 04:18 AM
Last Post: James_Yealink
  T26P: Does not register at the asterisk server on 5060 port but on 5062, 5063 etc. dimangelid 6 34,132 06-09-2015 05:04 PM
Last Post: carlo.passet

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication