[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
T46G - BLF name display too short
Author Message
eparker Offline
Junior Member
**

Posts: 2
Joined: Apr 2015
Reputation: 0
Post: #1
T46G - BLF name display too short
Right now when I provision a button for BLF and put in the name, you can't really read the name. The area defined for the names on the screen is simply too small. Is there a way to expand the area devoted to the name size so we can have more characters showing for the BLF names on screen? This is a big issue for my customers. Thanks!
04-29-2015 03:54 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Flora_Yealink Offline
Senior Member
****

Posts: 265
Joined: Oct 2012
Reputation: 2
Post: #2
RE: T46G - BLF name display too short
(04-29-2015 03:54 AM)eparker Wrote:  Right now when I provision a button for BLF and put in the name, you can't really read the name. The area defined for the names on the screen is simply too small. Is there a way to expand the area devoted to the name size so we can have more characters showing for the BLF names on screen? This is a big issue for my customers. Thanks!


Yes, please configure the "Label Length" with “Extended" under DSSKey page , in this case, it can show maxnum 27 characters
please refer to attached file.
Best Regards!


Attached File(s) Thumbnail(s)
   

Flora
FAE (Field Application Engineer) Department
Yealink Network Technology Co., Ltd.
Website: http://www.yealink.com
(This post was last modified: 04-29-2015 04:22 AM by Flora_Yealink.)
04-29-2015 04:18 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
eparker Offline
Junior Member
**

Posts: 2
Joined: Apr 2015
Reputation: 0
Post: #3
RE: T46G - BLF name display too short
(04-29-2015 04:18 AM)Flora Wrote:  Yes, please configure the "Label Length" with “Extended" under DSSKey page , in this case, it can show maxnum 27 characters
please refer to attached file.
Best Regards!

Perfect, just what I was hoping to find. Now, do you have any idea how to set that in the provisioning file? I have searched through it looking for it, but I can't find it. The page source lists it as DsskeyLength, but I can't find anything like that in the provisioning file. Any idea what they may call it in there? Thanks a lot!

Found another post about it. Looks like you have to add this:

features.config_dsskey_length = 1

I'll test it out and see if it works. Thanks again!
(This post was last modified: 04-29-2015 04:41 AM by eparker.)
04-29-2015 04:39 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Flora_Yealink Offline
Senior Member
****

Posts: 265
Joined: Oct 2012
Reputation: 2
Post: #4
RE: T46G - BLF name display too short
yes, please use features.config_dsskey_length=1 and let me know if any question.

Flora
FAE (Field Application Engineer) Department
Yealink Network Technology Co., Ltd.
Website: http://www.yealink.com
04-29-2015 05:14 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Geckoo Offline
Junior Member
**

Posts: 2
Joined: Jan 2018
Reputation: 0
Post: #5
RE: T46G - BLF name display too short
(04-29-2015 05:14 AM)Yealink_Flora Wrote:  yes, please use features.config_dsskey_length=1 and let me know if any question.

im unable to find it on the config template for 3cx? can you tell me were i can find it?
02-19-2018 04:32 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 993
Joined: Jan 2014
Reputation: 26
Post: #6
RE: T46G - BLF name display too short
(02-19-2018 04:32 PM)Geckoo Wrote:  
(04-29-2015 05:14 AM)Yealink_Flora Wrote:  yes, please use features.config_dsskey_length=1 and let me know if any question.

im unable to find it on the config template for 3cx? can you tell me were i can find it?

Yes, it is there.
If you run 3CX v15.5 SP3 you can find this parameter in the 3CX template under “Phone Features”

Kind regards,
Frank.

Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
02-20-2018 10:58 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Geckoo Offline
Junior Member
**

Posts: 2
Joined: Jan 2018
Reputation: 0
Post: #7
RE: T46G - BLF name display too short
(02-20-2018 10:58 AM)complex1 Wrote:  
(02-19-2018 04:32 PM)Geckoo Wrote:  
(04-29-2015 05:14 AM)Yealink_Flora Wrote:  yes, please use features.config_dsskey_length=1 and let me know if any question.

im unable to find it on the config template for 3cx? can you tell me were i can find it?

Yes, it is there.
If you run 3CX v15.5 SP3 you can find this parameter in the 3CX template under “Phone Features”
im unable to find it.

Code:
################################################################################​#######
##                    Phone Features                                                   ##
################################################################################​#######
#Enable or disable the phone to escape the pound key as percent sign followed by 23 when dialing out; 0-Disabled, 1-Enabled (default);
sip.use_23_as_pound =

sip.send_response_by_request =
sip.notify_reboot_enable =

#The following parameters only applicable to V80
sip.disp_incall_to_info =
sip.limit_server_name =
sip.limit_server_reason =
sip.tls_listen_port =
sip.trust_ctrl =
sip.timer_t1 =
sip.timer_t2 =
sip.timer_t4 =
custom.features.redial_via_local_sip_server.enable = 1
features.redial_via_local_sip_server.enable = 1
sip.terminate_notify_sub_delay_time =
sip.bind_local_addr_enable =
sip.user_agent_prefix =

##It is XSI authentication mode.0-Disable  1-Enable
sip.authentication_for_xsi = 0
##It is DSS KEY to call park type, whether the trigger BLF function.It takes effect after a reboot.
##The default value is 0-Disable(DSS KEY to call park type,triggering BLF function)   1-Enable
sip.call_park_without_blf = 0
##It is ASCII conversion into corresponding symbols.
##The defalult value is blank. 0-Disable   1-Enable
sip.escape_characters.enable =
##The default value is 0 ( said according to the transmission mode configured to listen on port),1-
##1-said at the same time to monitor TCP and UDP
##2-said to monitor TCP and UDP at the same time, and from the BLF - the LIST to subscribe to the contact with a transport = TCP parameters
sip.listen_mode = 0
##The default value is 0-Disable, 1-Enable.It takes effect after a reboot.
##0-registered according to the uri of the tectonic refer - by domain
##1-according to refer the from header fields to construct refer - by domain
sip.refer_by_header_auto_build = 0

##The default is blank.The Valid characters are digits - _.! ~ * # '() & Q462 = + R452 $,;?/ \ 0
##It is username needs to be preserved in a special notation.
sip.reserve_characters =
##The default value is 0.(contracting out the random contact, via port to carry fixed port).It takes effect after a reboot.
##1-the out-contracting port random contact, via port to carry
##2-the out-contracting ports fixed contact, via carry fix
sip.tcp_port_random_mode = 1
sip.tls_port_random = 1

#Enable or disable the RFC2543 Hold feature; 0-Disabled (default), 1-Enabled;
sip.rfc2543_hold = 0

##V81NEW##
sip.requesturi.e164.addglobalprefix=
sip.skip_redundant_failover_addr=
sip.request_validation.source.list=
sip.request_validation.digest.list=
sip.request_validation.digest.realm=
sip.request_validation.digest.realm=
sip.cid_source.preference=
sip.dns_transport_type=
sip.sdp_early_answer_or_offer=
sip.reliable_protocol.timerAE.enable=

##Send MAC address in UA.0-Disable  1-Enable(00:11:22:33:44:55) 2-Enable(001122334455)
sip.mac_in_ua = 2

#account.1.sip_server.Y.invite_retry_counts=
#account.1.sip_server.Y.only_signal_with_registered=
account.1.reg_failed_retry_min_time=
account.1.reg_failed_retry_max_time=
account.1.line_seize.expires=
account.1.gruu.enable=
account.1.sip_server.Y.failback_subscribe.enable=
account.1.hold_use_inactive=
[/code]

Found it, there are actually two parts of the phone features
(rond line 1600 and 1900) let see of it works.

i changed the value to 20 and i didnt work, ill try it with a factory reset of the phone and the value set to 1


Yeah worked! thanks !
(This post was last modified: 02-21-2018 01:57 PM by Geckoo.)
02-21-2018 01:39 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Line Key6-10 Greyd Out - T46G redmondsau 0 254 10-02-2020 07:38 AM
Last Post: redmondsau
  UH36 Support in T46G jinto.antony 1 412 10-01-2020 04:58 PM
Last Post: Yisroel_MongoTEL
  T46G Redefine Hold Button - Ques briankelly63 39 59,998 09-29-2020 09:07 PM
Last Post: chrisduncansb
  T46S/T46G show green icon (blf) although phones disconnected (Asterisk) jobst 0 251 09-16-2020 04:29 AM
Last Post: jobst
  caller ID source --> display permanently wouternotebaert 1 520 09-07-2020 02:47 PM
Last Post: David_Yealink
  Login button doesn't do anything...T46G jayg30 2 1,226 08-10-2020 05:45 AM
Last Post: Tee
  T46G - firmware downgrade jgolinuc 1 840 08-07-2020 02:05 PM
Last Post: complex1
  Display after picking up Handset Receiver - T48S cwatts@deltamodtech.com 3 1,175 06-25-2020 09:00 PM
Last Post: rickd@redseal.com
  T48G Shows "anonymous" in the display Lazzard 2 1,144 03-05-2020 07:04 PM
Last Post: Lazzard
  Yealink T46G Problems with BLFs n00604443 0 790 02-14-2020 04:35 PM
Last Post: n00604443

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication