T20P: Action URL, does it reboots on Register Failed?

[ruiseixas]

Hi,

I wold like to know if for my phone, this url setting will work whenever any sip "Register Failed":

Code:

http://192.168.22.126/cgi-bin/configmanapp.com?key=reboot

I'm using OpenVPN, and I wish to reboot the phone whenever I lost connection (Register Failed). If possible I wold like to specify a minimum time between reboots, for instance, 5 minutes. This will avoid systematic rebooting and the impossibility of accessing the phone web interface in the case of no network or bad sip configuration!

Code:

Firmware Version           9.71.0.140
Hardware Version           7.0.1.61

[Yealink Support]

Hi ruiseixas,

Our V71 has the new format of ACTION URI.
http(s)://phone IP address/servlet?key=variable value

You can refer to more detail from page 156 to page 160.
http://www.yealink.com/Upload/T2X/T2X-V7...71_141.pdf

[ruiseixas]

(11-22-2013 04:04 PM)Yealink Support Wrote:  Hi ruiseixas,

Our V71 has the new format of ACTION URI.
http(s)://phone IP address/servlet?key=variable value

You can refer to more detail from page 156 to page 160.
http://www.yealink.com/Upload/T2X/T2X-V7...71_141.pdf

Does it means the right address is this one:

Code:

http://192.168.22.126/servlet?key=Reboot

However, I try it in the Browser URL bar and my phone doesn't reboot!

Regards,
Rui

---

Ok,

I need to add my computer IP in the Remote control, and then it works. Any way, I think isn't needed to add the phone IP to this list to the action be executed by the phone URL actions...

I have a final question, if for some reason the phone is always unable to register, how do I access it via Web if it reboots all time due to no registration?

Regards,
Rui

[Yealink Support]

Hi Rui,

May be you can test XML Browser feature? We have released a latest version 72 today.
You can refer to xml browser feature.
http://www.yealink.com/SupportDownloadfi...7&flag=142

[ruiseixas]

(01-02-2014 03:36 PM)Yealink Support Wrote:  Hi Rui,

May be you can test XML Browser feature? We have released a latest version 72 today.
You can refer to xml browser feature.
http://www.yealink.com/SupportDownloadfi...7&flag=142

Hi,

When the phone fails registering there is no restart like expected. If I update the Firmware to the version you suggest will it works?

Regards,
Rui

[Yealink Support]

Hi ruiseixas,

I mean that you can test XML Browser which can help to control phone. And we change some templates in new version 72.
It is up to you to choosing.

[ruiseixas]

(11-15-2013 10:44 PM)ruiseixas Wrote:  Hi,

I wold like to know if for my phone, this url setting will work whenever any sip "Register Failed":

Code:

http://192.168.22.126/cgi-bin/configmanapp.com?key=reboot

I'm using OpenVPN, and I wish to reboot the phone whenever I lost connection (Register Failed). If possible I wold like to specify a minimum time between reboots, for instance, 5 minutes. This will avoid systematic rebooting and the impossibility of accessing the phone web interface in the case of no network or bad sip configuration!

Code:

Firmware Version           9.71.0.140
Hardware Version           7.0.1.61

Hi,

The solution is in the OpenVPN configuration file... You only need to add the following lines to it:

Code:

# Uncomment this section for a more reliable detection when a system
# loses its connection.  For example, dial-ups or laptops that
# travel to other locations.
ping 30
ping-restart 300

This means it pings each half minute, and after 5 minutes without response it restarts de VPN connection. You may chose a smaller period, I chose 5 minutes to guarantee that the DynDNS has the right updated address.

Consider also disabling persist-tun to a broader restart, this way:

Code:

persist-key
;persist-tun

Now the connection stays on all the time with no need to reboot the phone.


Regards
Rui

---

For more information about the OpenVPN config file, see my post named:

• T20P: VPN/OpenVPN - Just SIP or also RTP?