[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
T38G 38.70.0.125 -> 38.70.0.132 IPv6 broken
Author Message
bschmidt Offline
Junior Member
**

Posts: 8
Joined: Aug 2013
Reputation: 0
Post: #3
RE: T38G 38.70.0.125 -> 38.70.0.132 IPv6 broken
(08-16-2013 02:35 PM)Yealink Support Wrote:  Hi Bernhard,
You mean when you set IPV6 as Static IP Address on 38.70.0.125, everything works fine.
But when you set the same IPV6 as Static IP Address on 38.70.0.132, during the call, there's no any voice? But the account is register, and the can can also be made?

Yes, that's correct. The phone pings, is registered, is accessible via HTTP and calls can be made. Just no audio.

(08-16-2013 02:35 PM)Yealink Support Wrote:  Did you try to reset to factory default?

Could you provide PCAP trace, syslog(level 6) and config.bin file from these two different firmware to us, so we can analyze?
Before you export the syslog, please set log level as 6, and reboot the phone, then click Start,and reproduce the issue, then click Stop,and export the trace, syslog, config,bin to us.
(About where to export these files, please refer to attached screenshot.)
These three files are very important for us, hope you can kindly understand.

Sorry, no. The phone is broken at the moment, see my other thread at http://forum.yealink.com:81/forum/showth...hp?tid=737 . I have sent it to the distributor, as soon as I got a replacement I will try again.

BTW, are there any plans to get full IPv6 support? As far as I can tell there is not that much missing, just SLAAC (address autoconfiguration) and stateless DHCPv6. If you are afraid of regressions I would not mind a "global" IPv4-only/IPv6-only switch. Fully dual-stack would of course be preferred, but I have the feeling people are afraid of that.

Thanks,
Bernhard
08-19-2013 11:32 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Messages In This Thread
RE: T38G 38.70.0.125 -> 38.70.0.132 IPv6 broken - bschmidt - 08-19-2013 11:32 PM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Broken Certificate CAVoIPGirl 2 6,985 07-27-2021 01:19 AM
Last Post: CAVoIPGirl
  No Yeaklink support? Ticket pages broken ColinIsHere 0 3,855 06-12-2021 02:36 AM
Last Post: ColinIsHere
  T28P & T38G: Speed Dial delay or pause between DTMF yoda72 68 337,619 08-18-2019 09:06 PM
Last Post: HotlineExperts
  T38G reboots and answers call in speaker mode jraposinho 3 12,117 04-07-2017 08:02 PM
Last Post: ClearCall
  Hold Broken when dialing BLF Hope 1 7,187 02-13-2017 06:53 AM
Last Post: Quinlan_Yealink
  T28 and T38G Randomly using loudspeaker Jadzia 2 8,714 08-18-2016 08:41 AM
Last Post: Jadzia
  Forward Calls T38G jraposinho 1 8,012 03-15-2016 07:21 PM
Last Post: Karl_Yealink
  sip-t38g Repair rkellogg 1 7,277 10-31-2015 12:09 PM
Last Post: Klaus_Yealink
  T38G Incoming call pickup while on call. sac1500 0 5,917 10-02-2015 11:05 PM
Last Post: sac1500
  T38G Not Sending a BYE - Freeswitch rwhitlatch 5 15,692 08-18-2015 10:57 AM
Last Post: phnau

Forum Jump:


User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication