[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Dial tone keeps ongoing even when call is rejected at destination
Author Message
Phil2021 Offline
Junior Member
**

Posts: 12
Joined: Jul 2021
Reputation: 1
Post: #2
RE: Dial tone keeps ongoing even when call is rejected at destination
(09-01-2021 03:28 AM)w60B-Spain Wrote:  Hi,
I've found what seems to be an odd behaviour on my Yealink system. After some work, I've managed to get them (1x W60B + 2x W56H) registered and working properly on my office, meaning that I can do calls a receive calls without any problem.

Nevertheless, the issue comes when I'm either having an outgoing call from my office to a mobile or fixed line, and on destination, the call is rejected. It seems as if the Yealink devices were not "aware" of such rejection and then, I still can hear the dial tone going on for a while.
The same applies to an incoming call, where if the call is rejected at any of my yealink devices, the call originator still hears the dialling tones...

Is there anywhere on the configuration anything related to any code or something that needs to be adjusted so the telephones and the base do recognize the events of call termination and/or call rejection?

Thanks in advance,

Best

It sounds like the SIP messages are not getting through. You might want to check under Features and make sure 'Return Code When Refuse' is 486 (Busy Here) which is my setting on Sipgate and that works. I'm pretty sure I never changed any of those settings for Sipgate so that should be the default.

How are you rejecting the incoming call on the Yealink? Are you just pressing the red hang up button?

I've tested here (in the UK) and when I reject an incoming call from a mobile it goes to my voice mail on Sipgate, and when I reject a call to my mobile from Sipgate the call goes to my mobile voice mail (using a Yealink W60B and same handsets.)

Are you using the Sipgate proxy?

I've attached my settings for Sipgate so you can compare configuration. Note if you are behind a NAT then keepalive should be Enabled, I'm on IPv6 so don't need keep alive.


Attached File(s) Thumbnail(s)
       
(This post was last modified: 09-01-2021 04:50 PM by Phil2021.)
09-01-2021 04:48 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Messages In This Thread
RE: Dial tone keeps ongoing even when call is rejected at destination - Phil2021 - 09-01-2021 04:48 PM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Beep after ringing when call is answered cinergi 10 7,373 06-10-2022 08:33 AM
Last Post: SGFC
  Ring Tone Troube with W60B Zieschank_GmbH 1 1,104 04-13-2022 04:02 PM
Last Post: complex1
  Off-hook Auto-Dial (Hotline) missing Methodz86 3 3,290 10-15-2021 10:26 PM
Last Post: complex1
  Several seconds delay after accepting the call. mustimese 2 3,043 09-09-2021 05:02 AM
Last Post: mustimese
  W60B W56H 10 Seconds to dial phone number bcramer 4 5,524 04-02-2021 02:04 AM
Last Post: bcramer
  SCA showing call held but no soft key to retrieve on other handsets tima 1 4,357 03-04-2021 01:47 PM
Last Post: bdm
  Dial Timeout alanauld 1 3,202 01-10-2021 07:02 PM
Last Post: complex1
  Audio delay when call answered tjwesto 4 7,300 09-15-2020 01:56 PM
Last Post: complex1
  How to delete "missed call" notifcations from ALL w56H handsets at once? nangers123 3 6,382 07-10-2020 03:06 PM
Last Post: complex1
  Remove Missed Call notification from W60B stratos 0 2,863 01-24-2020 07:28 PM
Last Post: stratos

Forum Jump:


User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication