[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
speed dial to an IP address (ext@IP on value)
Author Message
anonymous1664059072296
Unregistered

 
Post: #2
RE: speed dial to an IP address
Dear Customer,

Good day. This is Garry from Yealink Technical Support Team.

We have created a Ticket for your question and you can go to the Ticket and provide the materials we need. When you reply in Ticket, make sure you enter your email address.
https://ticket.yealink.com/page/question...l?id=96392

1) Since you are using an early 80 firmware version of T58, it may be that the version is too long. You open the following link to download the latest firmware version of T58 (58.84.0.15) and start from there. See if the SpeedDial function working properly?
http://support.yealink.com/documentFront...mentId=268

2) DNS server failure can also cause this problem, you can try to check DNS server.

3) if your problem is not solved by the above two methods, We can ask you to provide diagnostic files (PCAP trace, level-6 log file and config.bin) for our analysis?
Here are the steps to get the diagnostic files(PCAP trace, level-6 log file and config.bin),
1) Go to the web UI of T58 -> Settings -> Configuration page
2) Drop down the page and you will see “Syslog Level “.( Set it to 6)
3) Drop down the page and you will see “Export All Diagnostic Files “ option.
4) Press Start. Then start to reproduce the problem.
5) To reproduce the issue: Look up the contact in Directory: 111@172.17.0.11, then call out, and hang up after the call is established successfully. Then, use the SpeedDial function you set for Key 37 to quickly broadcast a call to 111@172.17.0.11 ,you can finish the test., until you receive the prompt "invite request no response" .
6) After finishing test, press “Stop” and then “Export”. Please export it immediately after testing, just in case the messages been overwritten.
Then send us the exported file. We will locate your question based on the information you provide.

I am looking forward to your reply.

Best Regards
Garry
11-07-2019 11:41 AM
     Quote this message in a reply
Post Reply 


Messages In This Thread
RE: speed dial to an IP address - anonymous1664059072296 - 11-07-2019 11:41 AM
RE: speed dial to an IP address - EduardoV - 11-07-2019, 04:10 PM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  No IP address for W60 but T42 working ok heathb 2 1,636 03-09-2022 05:11 PM
Last Post: complex1
  Dial pause or delay jsubirana 0 1,738 12-01-2021 05:38 PM
Last Post: jsubirana
  Dial plan - How to include # at end of dial string cmadeiros@tecs.bm 5 8,007 12-11-2019 03:20 PM
Last Post: complex1
  ESS: refer to prompted value in speed dialing oliv 2 4,840 08-19-2019 01:01 PM
Last Post: oliv
  DND Dial 2 Codes at once Blake1 0 3,323 05-29-2018 02:25 PM
Last Post: Blake1
  Yealink Dial Plan RobertCrawford 8 17,774 03-09-2018 06:38 AM
Last Post: Johnny88
  how toadd image in remote address book of yealink phone? Olkan 1 6,364 07-28-2017 02:12 AM
Last Post: anonymous1664059072296
  SIP-T32G - Dial a number sent from a PC fails dspringer 1 6,277 08-15-2015 06:22 AM
Last Post: James_Yealink
  SIP 484 address incomplete vieri 5 16,485 03-27-2015 06:10 PM
Last Post: vieri
  SIP-T32G - Dial a number sent from a PC ITS 3 12,247 02-26-2015 10:46 PM
Last Post: CWR

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication