New Forum system requires email address which you used to apply for your account to replace your original username. Password stays the same.Please see this post for more details

Yealink Test Club has been officially launched. Please visit post below to get detail information. Come and join us!

We just had the YMCS online and we are also working on the features plan on the future versions, in this regard we are need to hear your voice about the YMCS.
Please visit :

Post Reply 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Configuration Yealink W52P for a GSM Gateway.
Author Message
Yea Offline
Junior Member

Posts: 2
Joined: May 2018
Reputation: 0
Post: #1
Configuration Yealink W52P for a GSM Gateway.
I am unable to establish a working line between the W52P and the Gateway.(This phone in its present state has a second line configured for an external VOIP service that is working fine.)
Incoming phonecalls work, outgoing phonecalls do not.
I am not using Asterisk or anything else then this gateway and the W52P and once they are configured I will disconnect WAN completely.
I want the W52P to use a mobile SIM and nothing else.
I really hope someone can help me out, because at this point I think I might have attempted all combinations brute force and I simply don't know where to go from here.

(hopefully) All relevant settings:

Firmware version:
Handset version:
Network Settings:
IP Address:
Primary DNS:
Subnet Mask:
Register Status Register Fail
Line active = Enabled
Label, Display Name, Register Name, User Name, Password = test
Enable outbound Proxy server, NAT Traversal = Disabled
SIP Server 1:
SIP Host =

Number assignement:
Headset1 is assigned for line 'test' for incoming as well as outgoing lines

SETTINGS Local Network
Router IP / internal network : / 192.168.0.x

SETTINGS GSM Gateway: Portech MV-372
Firmware: Ver = v10.115
Network mode: Bridged
WAN Settings:
Master IP:

Mobile to LAN Settings:
Item 0 | CID * | URL ;Accept all numbers and transfer to
LAN to Mobile Settings:
Item 0 | URL * | Call Num # ;No restrictions for the incoming IP address, one stage dialing.
SIP Settings
Mobile 1, Realm 1:
Display Name, User Name, Register Name, Register Password = test
Domain Server =
Proxy Server = -
Outbound proxy = -
Ports Setting
Port of Mobile 1:
SIP Port: 5060
RTP Port 20000
(This post was last modified: 05-31-2018 11:32 AM by Yea.)
05-31-2018 11:04 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 

Messages In This Thread
Configuration Yealink W52P for a GSM Gateway. - Yea - 05-31-2018 11:04 AM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  W52p Repair Aliaksandr 1 631 10-25-2019 07:12 AM
Last Post: FELIPE
  Action URI in W52P RRC_Support 1 200 10-22-2019 01:27 PM
Last Post: Garry_Yealink
  W52P Sporadic behavior with auto answer 2 3,647 09-27-2019 08:38 PM
Last Post: justingoldberg
  W52P Dect Interface "Settings" is missing ? CHRIYEA 1 617 06-06-2019 08:58 AM
Last Post: complex1
  W52P - Detected as Router and Telephone SG300 LLDP jmtread 1 2,175 12-21-2018 12:27 AM
Last Post: jmtread
  W52P admin pass after recovery crodaxy 1 1,372 12-04-2018 10:16 AM
Last Post: complex1
  W52P Handset Registration Fail CSPL 2 1,939 11-28-2018 06:00 AM
Last Post: CSPL
  W52P SfB Fred_ofi 0 895 10-18-2018 02:07 PM
Last Post: Fred_ofi
  W52P Issue with LLDP and VLAN ID derekb 2 3,434 07-22-2018 10:00 PM
Last Post: darwin.cabiluna
  W52P handset won't set up kennyb7 0 1,253 06-18-2018 01:01 AM
Last Post: kennyb7

Forum Jump:

User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication