[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
How to blacklist incoming call number?
Author Message
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,530
Joined: Jan 2014
Reputation: 45
Post: #7
RE: How to blacklist incoming call number?
(01-05-2018 07:23 AM)Michaelawertyuiol Wrote:  Hi.
I am struggling for hours now. I no longer have phone service and cannot start base set. It only has power light on.
I have googled and tried to recover following procedure. Procedures are all for Windows PC and I have only MacOS.

I do not understand how to connect as instructions are very unclear for such a technical procedure!!

I have downloaded the 3 files (.rom, .bin, .rfs) for TFTP server and placed in folder with read/write permissions. I set network settings as listed to
IP 192.168.0.23
Subnet 255.255.0.0
Router 192.168.0.1

There is no setting called "default gateway" - I presume this is "router" on Mac

I do power cable out, press and hold wifi button on base, plug in power.
Wait till all lights on.
Release wifi button.

Nothing happens. TFTP server log shows nothing. No file requests or transfers.

Firewall is off. Network cable Mac Ethernet -> hub switch -> LTE fiber router.
Base set network cable -> hub -> LTE fiber router

This configuration does not work as per instructions.

Only power led stays lit after a while. No activity in TFTP server log.


Obviously router is not considered in these instructions? How do I set up the hardware for this? What must plug into the base station Ethernet port?
Is there something else not considered?

If I plug Mac Ethernet directly into yealink base station and do power off, hold wifi button, power on, release wifi then all three led now lit. Still no activity in server log.

Waiting, waiting, no change, nothing is working...three led lights on but handset is searching for base forever so this is not correct.

The system is dead for use!

Please help. This was all started by base station upgrade which failed to work properly.

Hi,

Sad to read it does not work for you.

To reset the base to factory default please follow next steps carefully:
1. Disconnect power supply from base, but leave network cable connected
2. Long press Paging button on base, connect power supply, wait until all lights are on
3. Disconnect power, release Paging button, and reconnect power again

After excecute previous steps the base should get a new IP-address from your router. This can be checked in the router log.
Use this IP-address to log in to the base with the default username/password.

Where did you get the recovery files from? Yealink support?
They only provide these files on request if the user have a bricked device.
Recovery files are dedicated to each type of phone.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-05-2018 12:32 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Messages In This Thread
RE: How to blacklist incoming call number? - complex1 - 01-05-2018 12:32 PM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Slow to ring on incoming call rodcrux 1 7,954 01-25-2021 07:10 PM
Last Post: complex1
  internal call between two base stations fails janus 1 7,492 01-07-2021 07:20 PM
Last Post: complex1
  Handheld does not receive incoming calls dunzi 3 10,456 12-02-2020 10:41 PM
Last Post: complex1
  Is there no call history in web management panel in W52P? poznaniak 1 7,910 08-10-2020 12:49 PM
Last Post: complex1
  How do I set number of rings before voicemail answers? ettery 1 20,042 07-15-2019 12:25 AM
Last Post: Walter_Yealink
  Anon.Call Rejection, cannot disable DJ_HiP 4 15,877 09-03-2018 03:01 AM
Last Post: DJ_HiP
  call forward not working michael.gath 2 14,082 09-03-2018 02:09 AM
Last Post: okulhealth
  Cannot transfer incoming calls EverythingVoice 0 5,465 06-19-2018 10:36 AM
Last Post: EverythingVoice
  Incoming call ringing on another accounts phone Playboater 0 4,977 05-26-2018 09:38 PM
Last Post: Playboater
  W52P/RT20 registration/number of phones capable jonathon@californiatelecom.com 1 8,873 01-17-2018 09:43 AM
Last Post: Aishion_Yealink

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication