[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Provision second W52H to existing base and 3cx
Author Message
GreyFox Offline
Junior Member
**

Posts: 4
Joined: Oct 2015
Reputation: 1
Post: #11
RE: Provision second W52H to existing base and 3cx
(02-15-2016 12:06 AM)GreyFox Wrote:  Well, it turns out the answer is pretty simple. At least implementing the solution is. Not so easy when you don't know the solution.

Best practices would have you set up the first W52P, and then set up any remaining W52Hs you wish to connect to this first device. That includes registering the W52Hs. The next thing that needs to be done is to get your W52P provisoned/registered with your 3CX PBX. I have to admit that the plug and play implementation 3CX has with its approved telephone hardware units works pretty well. The next step is to set up all of your extensions in the 3CX that will be used by the various W52H units you have yet to get provisioned for the 3CX.

Now, here comes the non-documented part. First, make sure you have defined the extension that this new handset will use. Make a note of the handset user name (you get to configure this) and password (Your 3CX will generate one for you). Connect to the W52P web interface. You can do this either in the 3CX management portal, or you can simply use the IP address of the W52P in an Internet browser. Go to the Account tab. You will see the W52P you provisioned/registered above, and it will be identified as Account1. You will see that the Register Status is Registered. Make a note of all of the fields that are completed. Now, click on the pull-down arrow for Account1, and select Account2. You will see that the Register Status is is Disabled. Change the Line Active from Disabled to Enabled. Enter the Label, Display Name, and password you used in setting up the extension for this W52H in the 3CX. Leave all of the other fields the way they are with 2 exceptions: STUN Server and SIP Server 1 Server Host. Copy the STUN Server from Account1. Enter the IP address of your 3CX in the Server Host field. Click on Confirm, and watch the top of the screen where Register Status will go from Disabled to Registering to Registered.

That's it - you're done. I would test the extension to make sure it behaves the way you expect it to. Now, if you have any more W52Hs to connect, do the same thing. Don't forget that you can only subscribe a total of 5 handsets/accounts to the W52P.
02-26-2016 04:46 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Messages In This Thread
RE: Provision second W52H to existing base and 3cx - GreyFox - 02-26-2016 04:46 AM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Replace Base rfrantik@rfcinc.com 6 22,423 10-02-2024 01:19 AM
Last Post: keattto
  W80 Base Teams SIP Gateway Ascano 0 2,286 03-06-2023 06:12 PM
Last Post: Ascano
  W56H with W52P Base dmvcomms 7 12,224 03-06-2023 04:39 PM
Last Post: poznaniak
  not able to reigster to the base Janpreet 0 3,452 02-24-2023 12:16 AM
Last Post: Janpreet
  Completely reset a Yealink W52H MartijnSanders 0 4,524 01-17-2022 07:24 PM
Last Post: MartijnSanders
  Yealink W52H and diversion ringtone honzaa 3 9,151 10-07-2021 03:51 AM
Last Post: complex1
  internal call between two base stations fails janus 1 8,593 01-07-2021 07:20 PM
Last Post: complex1
  Wired headset W52H. SUCCESS ! michael.gath 2 16,274 08-13-2019 03:33 PM
Last Post: justingoldberg
  Can't de-register default base Nigutz 9 37,401 07-15-2019 09:11 PM
Last Post: GregoireG
  cannot transfer calls to every W52H handheld Basylnk 1 8,757 04-23-2018 07:21 AM
Last Post: anonymous1718628087441

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication