[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
W60B emitting high-pitched noise
Author Message
Phil2021 Offline
Junior Member
**

Posts: 12
Joined: Jul 2021
Reputation: 1
Post: #3
RE: W60B emitting high-pitched noise
(08-18-2021 09:37 AM)msncookie Wrote:  My W60B base has started to emit a loud high pitched noise or squeal. Angry It is about 3 years old and has been powered by a PoE switch with no issues until now. The noise starts as soon as it is connected to PoE/switch port. Wondering if anyone else has experienced this, but I presume my only option is to replace.

Thanks.

How can this reply be detected as spam then adding this sentence changes it enough to let it continue!

It will likely be coil wine from one of the power chokes, its a problem with all sorts of electrical equipment, a bit like a rattle in a car that develops, but someone else with the exact same car and model doesn't have it, just one of those things. It doesn't usually mean it is about to fail.

Unlikely resetting everything will help, unless the reset puts it back to a slightly different state and it's drawing a different amount of power, as that will adjust the frequency the coil runs at which might stop it resonating. You could try moving it to on its side or putting it flat for a while, it might stop after a while then as the coil vibrates and settles differently. It could also be one of the capacitors acting like a speaker as it is about to fail which could then stop it working.

If you are going to replace then first of all you could try some silicon type sealant and squish it into the coils on the PCB. The base opens easily enough, two screws then a nail running around the edge will eventually pop the top off. You will see on the PCB around 3 or 4 (depends on revision) little grey things marked with numbers on the top, like 220, 4R7 or 6RB and you will see around the sides a thin coil of wire, squishing some silicon sealant around them may dampen them enough to stop the coil whining.

Hope that helps
(This post was last modified: 08-18-2021 08:56 PM by Phil2021.)
08-18-2021 08:19 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Messages In This Thread
RE: W60B emitting high-pitched noise - Phil2021 - 08-18-2021 08:19 PM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  ‘New’ W56/W60B default admin password not recognised? Russ1 2 164 08-07-2022 02:44 PM
Last Post: Russ1
  All handsets on the same W60B loose registration after many attempts to register Alvaro Gutierrez 1 3,538 06-23-2022 09:56 PM
Last Post: rdurham
  W60B and W56H - can you PIN lock the phones,.. ? Haniel 2 5,437 06-18-2022 01:29 AM
Last Post: Beachnuttz
  Connecting WH66 to W60B aaronl 1 2,294 06-09-2022 10:00 PM
Last Post: markvdheijden
  Ring Tone Troube with W60B Zieschank_GmbH 1 1,142 04-13-2022 04:02 PM
Last Post: complex1
  recovery mode W60B files Aleskey 1 1,152 04-09-2022 02:42 AM
Last Post: 88fingerslukee
  W60B base firmware downgrade RingCentral brewginger 2 2,263 01-18-2022 12:58 AM
Last Post: brewginger
  Urgent - Help needed - W60B & W53H problems - firmware - connection - etc groenebeek 1 2,207 01-07-2022 06:16 PM
Last Post: complex1
  W60B Compromised and unable to factory reset socialtelecoms 3 3,091 01-07-2022 12:22 AM
Last Post: Yisroel_MongoTEL
Question W60B and W54H can't handle simultaneous calls... Need help BobbyfromParis 4 5,699 08-08-2021 01:12 AM
Last Post: testlabuser2015

Forum Jump:


User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication