[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
no dialtone or ringtone for w56p base and phones
Author Message
Marcbachman Offline
Junior Member
**

Posts: 2
Joined: Feb 2018
Reputation: 0
Post: #3
RE: no dialtone or ringtone for w56p base and phones
(06-18-2019 05:41 PM)complex1 Wrote:  
(06-18-2019 03:37 PM)Marcbachman Wrote:  Hello- I have had 4 w56 phones and the DECT base, w56 model, for a few years. I recently took down my entire network, ( router fizzled ), and have been working to get my phones back up. Registering has been an ongoing battle. My problem is that between registrations, when the phones partially work, I do not get a dialtone or a ringtone. I was able to dial out briefly today, and attempted to find whether there was any setting in the GUI for the base unit that were related to the ring/dial tones. My best guess is that this part of the system is not user configurable. My provider tells me that the tones are associated with my hardware and not part of the service. One suggestion is that there may be a defect with my power supply that causes the ringtone not to work. If there is an expert who reads this who knows about a reference for setting up a multi phone system and can provide me with details, I would be very appreciative. Thanks In Advance.

Hi,

If you have recently took down your entire network I suggest to reset your W56P base to factory default and setup the DECT set from scratch.
Then ensure the handsets are successfully registered to the base and try to register one account to your VoIP provider.
If this is done you can check if everything is functioning as you like.
Here you can find the User Guide (p24 and up) which can help to a successful set-up of the DECT set.
http://support.yealink.com/documentFront...mentId=110

Hope this will help.

My voip provider makes it difficult to register. I just got registered again today after 3 days of waiting, and found that my phone rings on incoming calls, and that there is a tone indicating a ring to target phone when making a call. My voip provider says I need to put the DECT base in a DMZ to get the dialtones to work. I did not have to do this previously. Unless there is an absolute need to reinitialize I would like to avoid that if possible.
06-18-2019 10:39 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Messages In This Thread
RE: no dialtone or ringtone for w56p base and phones - Marcbachman - 06-18-2019 10:39 PM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  W90DM SIP Gateway - W56P did not receive config after prov with code. Hexanet 0 1,945 03-31-2023 03:51 PM
Last Post: Hexanet
  W56H handset with W52 base? poznaniak 3 6,942 03-03-2023 04:35 AM
Last Post: complex1
  W56P answering randomly DavidDDD 4 12,921 06-15-2022 12:33 PM
Last Post: expositor
  Firmware for W56H and W52PW56P base Rajil 1 6,887 09-04-2021 04:06 AM
Last Post: complex1
  Multiple W56H's with One Base Station +FreePBX alankelly 2 9,863 05-04-2021 12:55 PM
Last Post: mlaihkw60b
  W56H handset on a Gigaset DECT base station working? Frank@Meeet 2 12,833 09-09-2020 05:56 PM
Last Post: trushing@askonecall.com
  Base inaccessible and dead eroubal2@comcast.net 2 10,647 06-24-2019 03:56 AM
Last Post: eroubal2@comcast.net
  How to read base data ? oliv 1 8,007 12-20-2018 08:07 AM
Last Post: complex1
  W56P Dial Now rules ipcsolutions 5 18,908 04-05-2018 06:44 AM
Last Post: Nology_Support
  W56P openvpn sha256 and 2048bit key PhoenixX777 1 7,370 03-20-2018 01:04 AM
Last Post: Lucia_Yealink

Forum Jump:


User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication