[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.

Post Reply 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Account Changes/Enable Delay
Author Message
jolouis Offline

Posts: 339
Joined: Oct 2013
Reputation: 6
Post: #2
RE: Account Changes/Enable Delay
Not sure about your point #2 with the DSS keys but generally Yealink tries to do provisioning "in the background". So normally the phone will boot, show the already configured setup on the display, and then a few seconds later after it has sent out provisioning requests and received updated config, it will do the merge and apply the updated settings.

Typically from time of the display showing the "normal idle" state to the updated one I expect it to be around 10-20 seconds, but that's using an unencrypted provisioning file being served by a local device rather than something "out in the cloud". You might be encountering additional delays due to provisioning file generation, network latency, etc.

Easiest way to tell for sure is to turn the syslog up to level 6, then reboot and let the phone do it's provisioning/updates. When you look at the syslog entries, you'll see lines for either ATP or AUTOP (depending on what Firmware version you're running). They are all timestamped, so you should be able to follow through the process and see if there are any excessive delays anywhere.

For reference, if your goal is simply to enable/disable Account 2 it may be faster to provision all of the account details at the same time your provision account 1, but just leave it disabled. Then, when you want to actually activate it, provision just the "account.2.enabled" as the only difference. I have not dealt with this in a while, but a few versions back that used to be the more efficient way of doing it.
04-18-2019 06:22 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 

Messages In This Thread
Account Changes/Enable Delay - Chris708 - 04-16-2019, 03:37 PM
RE: Account Changes/Enable Delay - jolouis - 04-18-2019 06:22 PM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  not able to get sip and account related details using action uri rajat_asthana 0 829 12-26-2023 03:51 PM
Last Post: rajat_asthana
  Key pad speed dial FAILS from non-default account jseeley 1 1,342 09-08-2023 05:56 AM
Last Post: jseeley
  Model T42s and T42g, the speakerphone is enable on incoming calls Lissvazquez 6 3,742 07-28-2023 10:27 PM
Last Post: complex1
  Send different codes on keystroke (enable and disable) Marsl84 0 1,147 04-21-2023 08:15 PM
Last Post: Marsl84
Question I am unable to register a new account under Account -> Register. Chris_Gc 5 5,425 02-09-2023 08:36 PM
Last Post: complex1
  Hotdesking extra account issue gareth20202 0 1,629 08-05-2022 08:06 PM
Last Post: gareth20202
  SIP account on the Yealink T46U suddenly Not Registered kmsfn 0 3,592 10-26-2021 04:44 PM
Last Post: kmsfn
Question Switch account on T48S - Outgoing caller ID remains at default account puregin 0 4,062 09-30-2020 09:52 AM
Last Post: puregin
  Two account on Yealink T46S f.barbier 1 6,375 06-10-2019 02:07 PM
Last Post: jolouis
  T46S Ringtone for each account GP 7 14,320 02-09-2019 08:34 AM
Last Post: complex1

Forum Jump:

User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication