[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.

Post Reply 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
T41S Custom logo only displays temporarily
Author Message
cwacker Offline
Junior Member

Posts: 4
Joined: Sep 2018
Reputation: 0
Post: #8
RE: T41S Custom logo only displays temporarily
(10-05-2018 08:10 PM)jolouis Wrote:  Honestly it is not worth fighting for. If you really want customized logo/display then use a higher level phone than the T41.

The reason Yealink switches between the logo and the idle screen is that the LCD is not capable of display the graphic and the fixed/idle information at the same time... they are rendered by two completely separate processes and just don't play well together. We went down this road many years ago back with the T28s and T26/T22s. The 28s worked great as the logo would always show in the blank area of the display, but on the lower phones they would just continually flip back and forth between the logo and the actual interface. At the time Yealink explained that was by design and quite frankly we had a hard time trying to argue differently.

It's nice branding to be able to customize the phone's appearance, but on sets with such small basic screens it's just not worth fighting over and these days with so many more models and features to focus on I doubt you will ever convince a Yealink dev to spend time on it for you.

If customized display is your primary concern the T29 is a reasonable compromise between the T46 and the more basic T41/T42. Styling is a little plainer but the screen is the same one used in the 46 and price point is about 30% more than T41 compared to 80% for T46. T52S may also be worth looking at.

That's a good possible solution. We were hoping we could just use the branding when the display goes into power saving mode (or a similar idea where the display is completely disabled and shows the logo until it's prompted with a status change of any sort)

We're fine without the logo since I haven't actually told anyone but my manager that it is a possibility. I was pretty careful to make sure I didn't say anything when marketing was in the room otherwise they'd be expecting miracles.

Fortunately, at this point, this is the only thing we could classify as an issue on the phones. Everything else is rock solid, and since these phones are going to be in areas where damage is likely, we're going to err on the side of ***** and functional instead of "can have branding".

Thank you for the notes. I really appreciate it.
10-05-2018 09:25 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 

Messages In This Thread
RE: T41S Custom logo only displays temporarily - cwacker - 10-05-2018 09:25 PM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  LCD DSS keys displays large buttons over date / time xuan69 2 356 11-03-2021 06:57 PM
Last Post: xuan69
  T41S lpelusi@konnectcommunications.co.uk 0 544 08-31-2021 08:53 PM
Last Post: lpelusi@konnectcommunications.co.uk
  T41S Recovery rfmjohn 3 2,358 06-19-2021 03:33 AM
Last Post: complex1
  T41S: Bridge current call with a second incoming call digitel 1 1,641 05-21-2021 04:15 PM
Last Post: complex1
  Need to remove custom Fonality firmware 1CCT 16 19,375 05-03-2021 08:24 PM
Last Post: kmconklin
  Yealink T41s Multiple sip Accounts scorpio313 0 1,725 07-30-2020 08:13 PM
Last Post: scorpio313
  Permanent forward T41S microdata 1 2,381 05-28-2020 03:56 PM
Last Post: jolouis
  T41P custom logo ausadmin 1 2,864 05-17-2020 08:21 AM
Last Post: complex1
  T41S units asking for last 5 digits of serial number then reseting to factory richard.vince 1 4,388 04-08-2020 08:16 AM
Last Post: complex1
  T41S pickup call with Swyxit qaztan 0 1,773 02-17-2020 04:39 PM
Last Post: qaztan

Forum Jump:

User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication