[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Multi-Line Phones, Line Type and Receiving Simultaneous Calls
Author Message
kmccracken Offline
Junior Member
**

Posts: 5
Joined: Feb 2013
Reputation: 0
Post: #1
Multi-Line Phones, Line Type and Receiving Simultaneous Calls
Phone Switch: Asterisk 11
Phone Models: T46G, T48G
Issue: When using all 6 accounts with the same credentials, several of the lines get stuck in a 'registering' state. As a result, calls to the phone would sometimes fail (depending on if the call would come in on an account that was registered properly or still in that stuck state).

In the past (and on older firmware versions), I would assign all six accounts to use the same login credentials. This worked just fine & the user could make/receive multiple calls at once. Life was good.

I'm not sure why it used to work and now it doesn't. I'm still using the exact same Asterisk box. Perhaps there was a change in firmware default settings and I'm not setting an appropriate value for my current configuration. Regardless, it worked in the past and now does not. The problem started manifesting itself in the last couple of firmware versions.

In the forums, I found reference to setting accounts 2-6 to be of a "Line" type. I'm using http file provisioning, so as an example of extension 111 (repeated for lines 3-6), I set them to:
linekey.2.label = 111
linekey.2.line = 1
linekey.2.type = 15

This got all of the icons on the phone to appear normal (green). On the web interface of the phone, status page, it now shows that there is only one registered line (line 1). But on the physical phone, lines 2-6 do show up as green phone icons. I can select any of the 6 line buttons on the phone and make a call. Life would appear to be good again. However, now if the user is on a phone call and an additional phone calls comes in, I get the unavailable status reported back from the phone, instead of an additional line ringing as it used to do.

Is there a setting that can be made to enable ringing on those extra lines (lines 2-6)?
02-25-2016 02:43 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Messages In This Thread
Multi-Line Phones, Line Type and Receiving Simultaneous Calls - kmccracken - 02-25-2016 02:43 AM

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Yealink T48S URL Line Key jogi29 1 799 06-10-2024 08:12 PM
Last Post: jogi29
  No dial tone when connecting calls internally tvettel 0 768 04-17-2024 02:20 PM
Last Post: tvettel
  T48S One Way Audio When Calls Are Put On Hold Or Transferred MJauja 1 1,556 03-09-2024 08:48 PM
Last Post: complex1
  Unable to Answer call without pressing Line 1 TheKirbyGroup 0 1,394 11-03-2023 11:04 PM
Last Post: TheKirbyGroup
  Display 0 for line pickup SupportA 0 1,770 07-12-2023 08:51 PM
Last Post: SupportA
  wrong default line with DECT Handset cbergmann 1 2,887 01-06-2023 07:44 PM
Last Post: complex1
  Yealink T19 can not automatically hangup inbound calls giaopc94 0 2,252 08-01-2022 09:28 AM
Last Post: giaopc94
  Missed calls list... caller id.. outbound route pattern savi 0 2,466 06-05-2022 03:09 PM
Last Post: savi
  Limit maximum of active calls per phone elastalink 5 16,797 09-09-2021 03:52 AM
Last Post: kapetrosyan
  Best way to manage line keys on multiple T48G/S sani390 0 4,034 07-01-2021 02:06 PM
Last Post: sani390

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication