[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
TIME OUT FOR DIAL-NOW: MINIMUM = 1 SECOND
Author Message
acrz6666 Offline
Junior Member
**

Posts: 4
Joined: Oct 2013
Reputation: 0
Post: #1
TIME OUT FOR DIAL-NOW: MINIMUM = 1 SECOND
Hello.

Why is it not possible to reduce the time out for dial-now rule to 0 seconds? I do not see the benefit of waiting one second, the minimum.

Regards.
10-26-2013 07:34 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
braymond Offline
Junior Member
**

Posts: 29
Joined: Nov 2013
Reputation: 0
Post: #2
RE: TIME OUT FOR DIAL-NOW: MINIMUM = 1 SECOND
I feel the same way. The phone should have the ability to dial as soon as a Dial-now rule is found.

Especially when the "Using Dial Plan Feature on Yealink SIP-T2XP Phones" guide says this (on page 3):
NOTE:
1) By default, the delay time for Dial-now would be 1 second
2) Configurable time would be 0~14seconds

Thanks,
Benoit
12-05-2013 09:25 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
deutschnaftyula Offline
Junior Member
**

Posts: 18
Joined: Nov 2013
Reputation: 1
Post: #3
RE: TIME OUT FOR DIAL-NOW: MINIMUM = 1 SECOND
I have a 0 and its working fine, just put 0Confused
01-03-2014 09:35 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ivanp Offline
Junior Member
**

Posts: 7
Joined: Jun 2014
Reputation: 0
Post: #4
RE: TIME OUT FOR DIAL-NOW: MINIMUM = 1 SECOND
(01-03-2014 09:35 AM)deutschnaftyula Wrote:  I have a 0 and its working fine, just put 0Confused

Neither T42 nor T46 allow setting value 0 for the dial-now time out. Both are on the latest firmware available: V72 (29.72.0.25 and 28.72.0.25)
06-10-2014 09:31 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ModCraig Offline
Moderator
*****

Posts: 716
Joined: May 2013
Reputation: 7
Post: #5
RE: TIME OUT FOR DIAL-NOW: MINIMUM = 1 SECOND
0 seconds is not good. I can't dial a 7 digit local call hat is near match to an internal extension.
Ie
Internal extension 4954
Local number 495-4000

If I have wait set to 0 - then I always get 4954 and not 495-4000.

Craig Reilly
MCSA, 3cx Advanced Certified
Scottsdale, AZ
06-10-2014 12:27 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
tsukraw Offline
Member
***

Posts: 142
Joined: Jan 2014
Reputation: 3
Post: #6
RE: TIME OUT FOR DIAL-NOW: MINIMUM = 1 SECOND
Just wanted to update this post.
In version 73 beta 2 release notes. It states
"Fixed the issue that Time Out for Dial-now Rule cannot be set to “0”.

I have tested it and zero does indeed work on the T46 and T48 now
10-13-2014 11:56 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Multicast time-to-live from 1 to 33 or a higher number than 1 at least David123321 0 1,391 10-09-2018 05:20 PM
Last Post: David123321
  Date/Time display in STATUS tab njackson 3 5,238 01-22-2018 08:04 PM
Last Post: KNERD
  W52H Speed Dial - Paging GIWM 3 1,914 01-05-2018 01:57 AM
Last Post: Evan_Yealink
  T48G Hide dial pad option brourk 5 5,996 06-17-2016 04:20 PM
Last Post: Yealink_Michael
  CP860 - Programmable Key: Speed Dial tsukraw 0 2,659 02-28-2015 01:38 AM
Last Post: tsukraw
  Time Zone for Uruguay. condor 2 4,234 10-16-2014 10:38 PM
Last Post: condor
  DTMF time duration bellopapo 2 6,614 10-31-2013 11:33 PM
Last Post: bellopapo
  Setup dial number in phone to use multicast paging rlsabin 2 6,558 10-17-2013 02:05 AM
Last Post: rlsabin
  Time Zone thumpertwin 1 3,701 10-14-2013 02:45 PM
Last Post: Yealink Support
  Second dial tone and dial from phonebook by handset off-hook xmichald 0 3,881 03-06-2013 08:04 AM
Last Post: xmichald

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication