[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Call Waiting: ring speaker on second call
Author Message
a.prottoborzone Offline
Junior Member
**

Posts: 1
Joined: Oct 2013
Reputation: 0
Post: #1
Call Waiting: ring speaker on second call
hello,

I have a Yealink T20 (Firmware Version 9.71.0.140, Hardware Version 7.0.1.61).
I have a problem with the service Call Waiting, I wish that on the second call, the phone rings from the speaker, not in the handset.

Features ---> General Information -> Call Waiting = enable
Features ---> General Information -> Call Waiting Tone = enable
Features ---> General Information -> Ringer Device for Headset = speaker

How can I do?

Thanks.

Andrea
10-08-2013 11:37 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
rlsabin Offline
Moderator
*****

Posts: 61
Joined: Nov 2012
Reputation: 2
Post: #2
RE: Call Waiting: ring speaker on second call
Andrea this feature has been requested multiple times, but I dont believe that as of now Yealink has chosen to add it in to their phones. Having an audible signal that is loud enough for coworkers to hear is great if they are providing call coverage for you. This has been a standard feature for decades on traditional key systems and PBX's. I believe that the only way to get the call waiting signal currently is through the handset or headset.

Rick
(This post was last modified: 10-09-2013 08:49 AM by rlsabin.)
10-09-2013 08:43 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
nicknomo Offline
Member
***

Posts: 63
Joined: Oct 2013
Reputation: 1
Post: #3
RE: Call Waiting: ring speaker on second call
Yes, unfortunately, it doesn't seem to use the speaker, but instead uses the handset if you are using it (different than a "headset" - your other choice).

To change the tone, I went into Phone-> Tones
I selected custom

Then I put this under call waiting
0/100,500/100,0/100,500/100,0/100,500/100,0/5000,0/100,500/100,0/100,500/100,0/100,500/100,0/15000

It gives two short little pulses 5 seconds apart to let the caller know there is another call coming in. The numbers are the tone and duration. Its going 0 tone (inaudbile) for 100 ms, tone 500 ("boop") for 100ms... it does this three times, then pauses for 5 seconds, then repeats one more time, then waits 15 seconds (which means the call goes to VM).
10-12-2013 04:46 AM
Find all posts by this user    like1    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  permisson to Call list on t46S ist denied wolfi30 1 288 03-04-2024 02:08 PM
Last Post: wolfi30
  permission denied to call list wolfi30 0 230 02-23-2024 08:54 PM
Last Post: wolfi30
  MP54 Call Forwarding pureit2018 0 494 11-23-2023 07:58 AM
Last Post: pureit2018
  Enhanced DSS Key - Conference Call joe1st 0 521 11-11-2023 05:27 AM
Last Post: joe1st
  Unable to Answer call without pressing Line 1 TheKirbyGroup 0 646 11-03-2023 11:04 PM
Last Post: TheKirbyGroup
  Yealink T28 setup audible ring on 2nd incoming call JeffWilkinson 20 86,315 10-18-2023 12:59 PM
Last Post: sles
  Picking up a call does not display Caller's Name oliv 0 1,296 04-19-2023 04:25 PM
Last Post: oliv
  Yealink T27P -Incoming call issue rsarceno 0 1,244 01-25-2023 08:54 AM
Last Post: rsarceno
Information T27G call foward all Aerium 0 1,332 09-13-2022 04:36 PM
Last Post: Aerium
  Remebering call volume settings SystemCraft 1 2,524 07-15-2022 07:42 PM
Last Post: complex1

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication