[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Multicast paging worked but no longer works
Author Message
plewis@bcradesign.com Offline
Junior Member
**

Posts: 7
Joined: Aug 2013
Reputation: 0
Post: #1
Multicast paging worked but no longer works
We have a lot of t28p phones with firmware 2.70.0.103, using 3cx.

We use Snoms for our paging, but in a couple of areas, we were using T28 with the new multicast paging feature, which was working, but it suddenly stopped, and we cannot get it working again on any T28. Paging still works as always on the SNOMs, so we know our networking is fine, and switch settings have not changed.

The interesting thing is, the phone receives the multicast signal, and displays properly, and the phone double beeps and then clicks like it wants to receive the audio, but nothing comes out of the speaker.

Can you suggest something for me to try?

Thanks,

phil

just noticed one difference between my snoms (where paging works) and t28 (paging doesn't work) and that's that the snom LAN address is static on 192.168.75.x:2048, and the yealink phones are DHCP and are using ports 5062, 5063, 5064, etc. could this be a factor?
(This post was last modified: 08-13-2013 01:10 AM by plewis@bcradesign.com.)
08-13-2013 12:42 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
CWR Offline
Moderator
*****

Posts: 716
Joined: May 2013
Reputation: 7
Post: #2
RE: Multicast paging worked but no longer works
check the audio codec in use as the static ip vs dhcp ip should not matter. multicast is using a different address range - right? ie: 239.0.0.1:50001


Code:
################################################################################​#######
##                              Multicast                                            ##                                            
################################################################################​#######

#Configure the codec of multicast paging.
multicast.codec = PCMU

#Enbale or diable the phone to handle the incoming multicast paging calls when there is a multicast paging call on the phone; 0-Disabled, 1-Enabled (default);
#If enabled, the phone will answer the incoming multicast paging call with a higher priority and ignore that with a lower priority.
multicast.receive_priority.enable = 0

#Configure the priority of multicast paging calls. It ranges from 0 to 10.
multicast.receive_priority.priority = 0

#Configure the listening multicast IP address and port number for the phone. X ranges from 1 to 10.
#multicast.listen_address.X.ip_address =
multicast.listen_address.1.ip_address = 239.0.0.1:50001

#Configure the lable displayed on the LCD screen when receiving the multicast paging. X ranges from 1 to 10.
#multicast.listen_address.X.label =
multicast.listen_address.1.label = PAGE
(This post was last modified: 08-13-2013 03:21 AM by CWR.)
08-13-2013 03:20 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
plewis@bcradesign.com Offline
Junior Member
**

Posts: 7
Joined: Aug 2013
Reputation: 0
Post: #3
RE: Multicast paging worked but no longer works
[quote='craigreilly' pid='2860' dateline='1376335234']
check the audio codec in use as the static ip vs dhcp ip should not matter. multicast is using a different address range - right? ie: 239.0.0.1:50001


[code]
################################################################################​#######
## Multicast ##
################################################################################​#######

#Configure the codec of multicast paging.
multicast.codec = PCMU
correct

where can I paste the text here - since most / all of the config files seem to be xml, not txt files.


################################################################################​​#######
## Multicast ##
################################################################################​​#######

#Configure the codec of multicast paging.
multicast.codec = PCMU

the common cfg files seem all to be in use - what has to happen to edit those, stop phone system?
(This post was last modified: 08-13-2013 03:54 AM by plewis@bcradesign.com.)
08-13-2013 03:27 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
CWR Offline
Moderator
*****

Posts: 716
Joined: May 2013
Reputation: 7
Post: #4
RE: Multicast paging worked but no longer works
Not sure what system you are on - so I can not help you...
I just know the Config files from Yealink are CFG files - which contain plain text.


Attached File(s)
.zip  t46-configs.zip (Size: 14.17 KB / Downloads: 20)
(This post was last modified: 08-13-2013 07:37 AM by CWR.)
08-13-2013 07:37 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Multicast / Paging / Intercom - Yealink T58 Ryandh 20 30,570 04-30-2020 03:23 PM
Last Post: Chris708
  Multicast Paging - Metaswitch EPP missing "Channel" ahull 1 2,421 11-27-2018 12:57 PM
Last Post: ahull
  MultiCast Paging CP860 admin.calgary.demac 4 7,966 09-02-2018 04:34 AM
Last Post: Infotec
  T27G no longer option to transfer call during ringing state DmitryTsyganov 1 3,080 04-16-2018 11:16 AM
Last Post: Travis_Yealink
  Multicast options not in manual USTI 1 3,170 01-18-2018 10:22 AM
Last Post: complex1
  Multicast/Intercom Philip954 5 8,348 09-02-2017 09:01 PM
Last Post: Ryandh
  Multicast Paging force speaker jolouis 6 9,458 10-14-2016 10:15 PM
Last Post: jolouis
  Yealink T28p no longer working after CudaTel firmware update AshElsayid 1 5,634 01-20-2015 08:52 PM
Last Post: James_Yealink
Information T28P Multicast Paging Volume fdtcloud 1 5,852 10-09-2014 08:14 PM
Last Post: Wilson_Yealink
  Muticast paging issues RyanW 5 12,496 02-25-2014 09:38 PM
Last Post: RyanW

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication