[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
BLF Pickup Not Working
Author Message
Mark Lloyd Offline
Junior Member
**

Posts: 4
Joined: Jun 2013
Reputation: 0
Post: #1
BLF Pickup Not Working
Yealik T26

Firmware 6.70.23.2
Hardware 4.0.1.38

BLF is configured and functional but pickup is not working.

Config as follows

LineKey 2 = BLF
Line = Line 1 (2201 in our lab)
Value = 2204
Ext = 33

When a phone 2203 dials 2204 the BLF key on 2201 flashes green but when you press the key it dials out to 2204 instead of dialling 332204. Call on ringing phone is replaced with the call from the phone ie 2201.

If you grab line 1 and manually dial 332204 then the pickup works fine so I can only assume the phone is not correctly dialling 33 when pressing the flashing BLF key

Any ideas?
06-04-2013 01:10 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
kg4ysy Offline
Member
***

Posts: 65
Joined: May 2013
Reputation: 2
Post: #2
RE: BLF Pickup Not Working
You may need these settings in your provision file. I'm sure there is a place in the web interface for it too.

features.pickup.direct_pickup_enable = 1
features.pickup.direct_pickup_code = 33
06-04-2013 09:10 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Mark Lloyd Offline
Junior Member
**

Posts: 4
Joined: Jun 2013
Reputation: 0
Post: #3
RE: BLF Pickup Not Working

.txt  yealink BLF Pickup.txt (Size: 82.71 KB / Downloads: 3)
(06-04-2013 09:10 PM)kg4ysy Wrote:  You may need these settings in your provision file. I'm sure there is a place in the web interface for it too.

features.pickup.direct_pickup_enable = 1
features.pickup.direct_pickup_code = 33

Hey thanks for the tip but it did not help. I found the area in the www interface and added them and retested.

What is very interesting however is that I found a setting called

visual alert for BLF pickup. I turned that on and now the screen of the phone displays who is calling whom and there is a softkey for pickup.

That softkey correctly dials 332204 and the pickup takes place. I have confirmed via testing that its using the pickup code defined in the options above and NOT the extn value assigned to the key.

I'm assuming that I am correct in thinking that pressing the flashing BLF line key should initiate a pickup when its flashing?

To me it simply appears to be ignoring that value assigned to the linekey AND dsskey for that matter since I have just tested a BLF on dss key 1 and the same thing occurs.

Have now attached Lvl6 syslog from the phone that shows pickup being performed but no pickup code being used in the SIP Invite
(This post was last modified: 06-06-2013 10:24 AM by Mark Lloyd.)
06-06-2013 05:23 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
kg4ysy Offline
Member
***

Posts: 65
Joined: May 2013
Reputation: 2
Post: #4
RE: BLF Pickup Not Working
I looked through my configuration again and I have this for a BLF key. Note that I put in linekey.3.pickup_value = 195 which is my DCPU code. That should fix it. Sorry for the runaround on that. I forgot the key itself needed that value.


#linekey.3.label = Justin
#linekey.3.type = 16
#linekey.3.line = 0
#linekey.3.value = 4712
#linekey.3.pickup_value = 195
06-06-2013 08:12 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Display 0 for line pickup SupportA 0 1,101 07-12-2023 08:51 PM
Last Post: SupportA
  No IP address for W60 but T42 working ok heathb 2 3,918 03-09-2022 05:11 PM
Last Post: complex1
  DHCP not working on T26P when OpenVPN is enabled. LandonL 11 35,890 05-12-2021 10:46 AM
Last Post: 1sae
  MWI not working with Fritzbox frappy 0 3,897 10-05-2020 08:34 PM
Last Post: frappy
  Directed Call pickup Caller ID Casey Roll 6 18,047 05-27-2017 10:42 AM
Last Post: Jensen_Yealink
  Missed Calls messages after pickup and in queues Kamik 2 9,603 12-14-2016 07:05 PM
Last Post: nick.spannagel
Sad T41P BLF ligth not working goHelpDesk.com 2 9,824 10-15-2016 02:10 AM
Last Post: CWR
  T46G Issues Save Volume settings + BLF pickup Jeroen 3 13,787 08-31-2016 02:47 AM
Last Post: CWR
  Call Pickup History missing alpashm 2 8,827 03-01-2016 07:05 PM
Last Post: Frank Drews
  Pickup BLF T38G Anna 4 11,966 12-30-2015 12:34 AM
Last Post: AerioBrian

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication