[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Upgraded firmware, bad news
Author Message
ctsmetrony Offline
Junior Member
**

Posts: 13
Joined: Dec 2017
Reputation: 0
Post: #1
Upgraded firmware, bad news
In trying to register my W52P with a 3CX pbx, the 3CX instructions had me upgrade firmwares for the base and handsets. For the base, I downloaded and installed 1529371429716.81.0.30.rom and then W56H-61.85.0.35.rom for the handsets. It's been a mess ever since. At one hopeful point, the base was pingable and the first handset I tried seemed to register but it went into some interminable "Initializing" message. The other handset could not find the base. I have not been able to reach the base's web page and, after another base hard reset, it is not pinging.

I would appreciate steps that might salvage this equipment.

Thanks
09-26-2022 10:41 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,509
Joined: Jan 2014
Reputation: 44
Post: #2
RE: Upgraded firmware, bad news
(09-26-2022 10:41 PM)ctsmetrony Wrote:  In trying to register my W52P with a 3CX pbx, the 3CX instructions had me upgrade firmwares for the base and handsets. For the base, I downloaded and installed 1529371429716.81.0.30.rom and then W56H-61.85.0.35.rom for the handsets. It's been a mess ever since. At one hopeful point, the base was pingable and the first handset I tried seemed to register but it went into some interminable "Initializing" message. The other handset could not find the base. I have not been able to reach the base's web page and, after another base hard reset, it is not pinging.

I would appreciate steps that might salvage this equipment.

Thanks

Hi,

Please downgrade the W56H firmware to 61.83.0.50 because this version is fully compatible with v81 version of the base.
https://support.yealink.com/en/portal/do...89de274bdf

Please note:
After a firmware upgrade/downgrade, base or handset, a reset to factory default is required.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
09-26-2022 11:05 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ctsmetrony Offline
Junior Member
**

Posts: 13
Joined: Dec 2017
Reputation: 0
Post: #3
RE: Upgraded firmware, bad news
I think I'm stuck. Every time I register the handset in an effort downgrade its firmware, everything freezes. I get "Data initializing..." on the handset and the base's web interface freezes. Eventually, the base is unpingable.
09-29-2022 09:59 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,509
Joined: Jan 2014
Reputation: 44
Post: #4
RE: Upgraded firmware, bad news
(09-29-2022 09:59 PM)ctsmetrony Wrote:  I think I'm stuck. Every time I register the handset in an effort downgrade its firmware, everything freezes. I get "Data initializing..." on the handset and the base's web interface freezes. Eventually, the base is unpingable.

Hi,

Have you reset the base?

Please reset to factory default using following steps:
1. Disconnect power supply from base, but leave network cable connected
2. Long press Paging button on base, connect power supply, wait until all lights are on
3. Disconnect power, release Paging button, and reconnect power again

When base station reset finishes, the power indicator LED, network status LED and registration LED illuminate in sequence. System PIN and all individual settings are reset to factory defaults. Handset registrations will also be cleared after base station reset.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
09-30-2022 12:34 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ctsmetrony Offline
Junior Member
**

Posts: 13
Joined: Dec 2017
Reputation: 0
Post: #5
RE: Upgraded firmware, bad news
I've reset the base many times. The lockup happens after reset and when registering the handsets that have the new (wrong) firmware.

I think I have good handsets and a good base that will never work together again. Is there another base (the W70B perhaps) is compatible with handsets loaded with that 61.85.0.35 firmware?

Thanks
09-30-2022 10:10 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ctsmetrony Offline
Junior Member
**

Posts: 13
Joined: Dec 2017
Reputation: 0
Post: #6
RE: Upgraded firmware, bad news
Is there another base (the W70B perhaps) is compatible with handsets loaded with that 61.85.0.35 firmware?
10-07-2022 01:06 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,509
Joined: Jan 2014
Reputation: 44
Post: #7
RE: Upgraded firmware, bad news
(10-07-2022 01:06 AM)ctsmetrony Wrote:  Is there another base (the W70B perhaps) is compatible with handsets loaded with that 61.85.0.35 firmware?

Yes, the W70B f/w 146.85.0.25 is compatible with the W56H f/w 61.85.0.35
https://support.yealink.com/en/portal/do...ebd40b60c4

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
10-07-2022 03:17 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ctsmetrony Offline
Junior Member
**

Posts: 13
Joined: Dec 2017
Reputation: 0
Post: #8
RE: Upgraded firmware, bad news
Great, thanks.
10-07-2022 05:46 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  W52P Firmware upgrade aunijaffer@gmail.com 5 12,345 09-07-2021 11:42 PM
Last Post: complex1
  Unable to update firmware Gunter 1 11,179 07-10-2020 12:50 PM
Last Post: nolto
  w52p handset. Firmware keeps reverting to old version after upgrade. farrago 0 5,494 07-23-2017 07:00 PM
Last Post: farrago
  Firmware won't upgrade to handset Jeroen 3 12,516 06-06-2017 04:58 PM
Last Post: complex1
  Downgrade w52p firmware herman 1 9,803 01-06-2017 05:41 PM
Last Post: complex1
  Downgrading Base firmware to 25.73.0.27 from 25.73.0.40 bharat@metro 3 16,422 07-20-2016 08:53 PM
Last Post: complex1
  W52P latest firmware JackDan 2 14,019 06-19-2016 09:38 AM
Last Post: JackDan
  Firmware Versions dnsug 1 8,562 01-30-2016 11:46 PM
Last Post: complex1
  Downgrade Firmware? mloiterman 1 10,117 12-30-2015 05:49 AM
Last Post: Yealink_Michael
  Base Firmware... PLEASE HELP!!! virtualsupport 2 8,555 10-22-2015 12:00 PM
Last Post: Gasmanz

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication