[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
W60B and W54H can't handle simultaneous calls... Need help
Author Message
BobbyfromParis Offline
Junior Member
**

Posts: 2
Joined: Apr 2021
Reputation: 0
Post: #1
Question W60B and W54H can't handle simultaneous calls... Need help
Hello,

I set up Yealink W60B and 4 W56H handset with Aircall (VoIP provider) and everything works like a charm, EXCEPT the fact that when an other call is made while one is currently going on, the other handset are not ringing.

Ex : Customer A calls -> All 4 handsets ring, one of them take the call.

Then, while customer A is on the phone, customer B is calling. There is a ring tone for him, like if it was ringing for real on the other side, but unfortunately, everything stays quiet, not a single handset is ringing.

If I end the call with customer A while customer B is still hanging ringing, then all the handset start ringing again. It's the very last step to get my solution working like a charm :-)

Anyone can help ?
04-19-2021 11:27 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,541
Joined: Jan 2014
Reputation: 48
Post: #2
RE: W60B and W54H can't handle simultaneous calls... Need help
(04-19-2021 11:27 PM)BobbyfromParis Wrote:  Hello,

I set up Yealink W60B and 4 W56H handset with Aircall (VoIP provider) and everything works like a charm, EXCEPT the fact that when an other call is made while one is currently going on, the other handset are not ringing.

Ex : Customer A calls -> All 4 handsets ring, one of them take the call.

Then, while customer A is on the phone, customer B is calling. There is a ring tone for him, like if it was ringing for real on the other side, but unfortunately, everything stays quiet, not a single handset is ringing.

If I end the call with customer A while customer B is still hanging ringing, then all the handset start ringing again. It's the very last step to get my solution working like a charm :-)

Anyone can help ?

Hi Bobby,

Let me guess... you have setup the W60P with only one SIP account and the 4 handsets are connected with that account.
Yes? Then this will not work.
If you want the handsets to ring on an incoming call, then each handset must have it's own account.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
04-20-2021 01:34 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
BobbyfromParis Offline
Junior Member
**

Posts: 2
Joined: Apr 2021
Reputation: 0
Post: #3
RE: W60B and W54H can't handle simultaneous calls... Need help
Hi complex1,

Thanks for the quick answer ! If I understand well, it means that :

1) There is a "main" phone number where all the calls will be directed. All handset will ring and one of them take the call, regardless of the phone line linked to it.
2) When there is a second call, it will ring on the other handsets but the call will be directed to an other phone line where the number is not displayed to customer B.
3) When I initiate a call from any one of the handset, it will display the primary phone number to the customer, regardless of the phone line attached to the handset.

Am I right ? Thanks for your kind help !
(This post was last modified: 04-20-2021 11:53 PM by BobbyfromParis.)
04-20-2021 11:52 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Babylonia Offline
Junior Member
**

Posts: 39
Joined: Jun 2019
Reputation: 0
Post: #4
RE: W60B and W54H can't handle simultaneous calls... Need help
What @complex1 is writing is true as for using several VOIP devices / phones.
(E.g. a desktop phone with its own SIP account).

But not so as for several wireless DECT hand sets.
Base Station can use just one SIP-account.
But all hand sets should allow to make there own call by the same SIP-account.

At least in my situation I have a normal work around by that.
Just made a test again, and all is running like that.

Test 1 - calling by mobile phone to SIP account A ===> all hand sets ringing
I just take the call, so open connection.

Test 2 - calling by a desktop phone (total different line / number and SIP account)
to SIP account A ===> the other DECT hand sets are ringing.
I just can take the call, so open connection by a second hand set.

So two different open calls, just using the same "SIP account A" by the base station.

This is one of the advantages of a DECT solution, in opposite to e.g. separate desktop phones.
04-24-2021 01:46 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
testlabuser2015 Offline
Junior Member
**

Posts: 8
Joined: Dec 2015
Reputation: 0
Post: #5
RE: W60B and W54H can't handle simultaneous calls... Need help
Sounds like the number of simultaneous calls per handset/registered sip account on the phone may be set to 1.
You can log into the WebUI of the W60 Base, go to Account > Advanced > scroll to the bottom, its the last setting.
I would also check Features > General Information >> Call Waiting, it may not be enabled.
Regarding these options, you may also want to confirm with your ITSP (VoIP) provider to see if they support them or not.
Some ITSP's do not include Call Waiting by default and may not allow more than one call per device/user at a time.
08-08-2021 01:12 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  how to register a T58W with DD10K to a W60B? schogol 6 3,153 04-16-2024 09:54 PM
Last Post: schogol
  [W70B Basis + W73H Handset] 2nd line for foreign country calls der.ronny@gmx.net 1 1,512 03-20-2024 09:34 PM
Last Post: complex1
  How to enable web server/ GUI on W60B and W70B after provisioning has disabled it. jhofford 2 4,362 09-12-2023 08:42 PM
Last Post: jhofford
  Problems setting up W60B and interface issues Ness 4 7,828 03-30-2023 05:24 PM
Last Post: Ness
  Auto Provision firmware on W60B base station hospitale 6 8,471 02-15-2023 05:54 PM
Last Post: hospitale
  recovery mode W60B files Aleskey 3 6,834 02-14-2023 01:42 AM
Last Post: 88fingerslukee
  W60B Constantly Restarts When W73H Is Connected. nolto 0 2,336 02-07-2023 12:15 AM
Last Post: nolto
  W60B factory reset and default login carsey 3 10,057 02-01-2023 02:52 AM
Last Post: complex1
  W60B remove intercom when transfert MYCOMPUTING 2 3,662 12-08-2022 12:17 AM
Last Post: complex1
  W60B base With 56H ( incomming calls, no ringing when charging ) stéphane 3 10,305 12-01-2022 03:15 AM
Last Post: therring

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication