[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
speed dial to an IP address (ext@IP on value)
Author Message
EduardoV Offline
Junior Member
**

Posts: 3
Joined: Nov 2019
Reputation: 0
Post: #1
speed dial to an IP address (ext@IP on value)
Hi everybody,

I'm trying to configure speed dial keys on yealink T58A with firmware version 58.80.0.40 (only one of the phones) and the rest with 58.80.0.10.

Seems it used to work and no longer does (nobody has upgrade devices).

Related configuration on a couple of test phones:

* Accept SIP trust server only: disabled
* Allow IP call: enabled
* Remote control: action URI: any

Configuration of expansion1 ext Keys on DSSkeys:

For example--> key 37

* Speed dial
* Value: 111@172.17.0.11
* Label: username
* Line: Line1
* Extension: leave blank

For testing I go to Directory / Local directory and create a user with office phone 111@172.17.0.11 and get a call success.

But if user press key37 in that case he gets an error without code stating "invite request no response".

Is there a way to solve it?

Is that a recommended practice ?

Also, is there a workaround or naming convention I don't follow?

I got syslog installed and devices reporting to it in case you need logs.

THanks a lot,

Ed
11-06-2019 05:31 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
anonymous1711612242218
Unregistered

 
Post: #2
RE: speed dial to an IP address
Dear Customer,

Good day. This is Garry from Yealink Technical Support Team.

We have created a Ticket for your question and you can go to the Ticket and provide the materials we need. When you reply in Ticket, make sure you enter your email address.
https://ticket.yealink.com/page/question...l?id=96392

1) Since you are using an early 80 firmware version of T58, it may be that the version is too long. You open the following link to download the latest firmware version of T58 (58.84.0.15) and start from there. See if the SpeedDial function working properly?
http://support.yealink.com/documentFront...mentId=268

2) DNS server failure can also cause this problem, you can try to check DNS server.

3) if your problem is not solved by the above two methods, We can ask you to provide diagnostic files (PCAP trace, level-6 log file and config.bin) for our analysis?
Here are the steps to get the diagnostic files(PCAP trace, level-6 log file and config.bin),
1) Go to the web UI of T58 -> Settings -> Configuration page
2) Drop down the page and you will see “Syslog Level “.( Set it to 6)
3) Drop down the page and you will see “Export All Diagnostic Files “ option.
4) Press Start. Then start to reproduce the problem.
5) To reproduce the issue: Look up the contact in Directory: 111@172.17.0.11, then call out, and hang up after the call is established successfully. Then, use the SpeedDial function you set for Key 37 to quickly broadcast a call to 111@172.17.0.11 ,you can finish the test., until you receive the prompt "invite request no response" .
6) After finishing test, press “Stop” and then “Export”. Please export it immediately after testing, just in case the messages been overwritten.
Then send us the exported file. We will locate your question based on the information you provide.

I am looking forward to your reply.

Best Regards
Garry
11-07-2019 11:41 AM
     Quote this message in a reply
EduardoV Offline
Junior Member
**

Posts: 3
Joined: Nov 2019
Reputation: 0
Post: #3
RE: speed dial to an IP address
(11-07-2019 11:41 AM)Garry_Yealink Wrote:  Dear Customer,

Good day. This is Garry from Yealink Technical Support Team.

We have created a Ticket for your question and you can go to the Ticket and provide the materials we need. When you reply in Ticket, make sure you enter your email address.
https://ticket.yealink.com/page/question...l?id=96392

1) Since you are using an early 80 firmware version of T58, it may be that the version is too long. You open the following link to download the latest firmware version of T58 (58.84.0.15) and start from there. See if the SpeedDial function working properly?
http://support.yealink.com/documentFront...mentId=268

2) DNS server failure can also cause this problem, you can try to check DNS server.

3) if your problem is not solved by the above two methods, We can ask you to provide diagnostic files (PCAP trace, level-6 log file and config.bin) for our analysis?
Here are the steps to get the diagnostic files(PCAP trace, level-6 log file and config.bin),
1) Go to the web UI of T58 -> Settings -> Configuration page
2) Drop down the page and you will see “Syslog Level “.( Set it to 6)
3) Drop down the page and you will see “Export All Diagnostic Files “ option.
4) Press Start. Then start to reproduce the problem.
5) To reproduce the issue: Look up the contact in Directory: 111@172.17.0.11, then call out, and hang up after the call is established successfully. Then, use the SpeedDial function you set for Key 37 to quickly broadcast a call to 111@172.17.0.11 ,you can finish the test., until you receive the prompt "invite request no response" .
6) After finishing test, press “Stop” and then “Export”. Please export it immediately after testing, just in case the messages been overwritten.
Then send us the exported file. We will locate your question based on the information you provide.

I am looking forward to your reply.

Best Regards
Garry

Hi Garry,

Thanks a lot for reply.

1.-) Updated firmware to latest rom on a couple of devices for testing with no issues. Devices are on ext 109 and 111 at ip's 172.17.0.9 and 172.17.0.11

2.-) DNS are public google ones received by network appliance on voice vlan 2 at 172.17.0.0/24.

3.-) Testing new rom, but after upgrade I receive a call failed on same phones
Doing diag files and little test to provide you with the material

I'll update threat when material are posted to ticket to let you know they're uploaded.

Ed
11-07-2019 04:10 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
EduardoV Offline
Junior Member
**

Posts: 3
Joined: Nov 2019
Reputation: 0
Post: #4
RE: speed dial to an IP address (ext@IP on value)
Hi Garry,

I get an error on ticket link, access denied error, so I created another ticket (96454)

Material is uploaded.

Thanks,

Ed
11-07-2019 07:43 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Dial replace Scottie 0 889 06-11-2023 06:33 PM
Last Post: Scottie
  Dial Plan on W70B feedgenic 0 1,434 10-03-2022 04:58 PM
Last Post: feedgenic
  No IP address for W60 but T42 working ok heathb 2 3,921 03-09-2022 05:11 PM
Last Post: complex1
  Dial pause or delay jsubirana 0 3,123 12-01-2021 05:38 PM
Last Post: jsubirana
  Dial plan - How to include # at end of dial string cmadeiros@tecs.bm 5 11,242 12-11-2019 03:20 PM
Last Post: complex1
  ESS: refer to prompted value in speed dialing oliv 2 6,486 08-19-2019 01:01 PM
Last Post: oliv
  DND Dial 2 Codes at once Blake1 0 4,254 05-29-2018 02:25 PM
Last Post: Blake1
  Yealink Dial Plan RobertCrawford 8 23,021 03-09-2018 06:38 AM
Last Post: Johnny88
  how toadd image in remote address book of yealink phone? Olkan 1 7,782 07-28-2017 02:12 AM
Last Post: anonymous1711612242218
  SIP-T32G - Dial a number sent from a PC fails dspringer 1 7,563 08-15-2015 06:22 AM
Last Post: James_Yealink

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication