[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
W52p Repair
Author Message
Engineer - Pavel Zhuk Offline
Junior Member
**

Posts: 1
Joined: Apr 2018
Reputation: 0
Post: #1
W52p Repair
What kind of connector (J100) on the base W52P board?
The base does not start, LAN port doesn't light up.
Is it possible to restore it?


Attached File(s) Thumbnail(s)
   
(This post was last modified: 04-24-2019 05:42 AM by Engineer - Pavel Zhuk.)
04-24-2019 05:41 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
FELIPE Offline
Junior Member
**

Posts: 2
Joined: Oct 2019
Reputation: 0
Post: #2
RE: W52p Repair
(04-24-2019 05:41 AM)Aliaksandr Wrote:  What kind of connector (J100) on the base W52P board?
The base does not start, LAN port doesn't light up.
Is it possible to restore it?


Hi.
same problem than this.
It doesn,t reach to get LAN. Light LAN is off. And I don,t have throught the hand set the menu to change IP or anythink.
how to reset base ?? I have tried pushing the icon to looking for handset and turning off the power supply but the 3 lights start on and nothing changed.
any idea ???

thnks rgds
10-25-2019 07:12 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
RobertoDSM Offline
Junior Member
**

Posts: 9
Joined: Jan 2020
Reputation: 0
Post: #3
RE: W52p Repair
Hello everybody!

I have the same problem and hope that someone could help us.

I tried to reset the base, pressing and holding the button while connecting to power supply, but after the three leds on, nothing else happens.

Maybe there's another way to test the base?
Or something to do in order to know if the base still works?

Thankyou.
01-15-2020 10:17 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,509
Joined: Jan 2014
Reputation: 43
Post: #4
RE: W52p Repair
Hi,

Please factory reset with following steps:
1. Disconnect power supply from base, but leave network cable connected
2. Long press Paging button on base, connect power supply, wait until all lights are on
3. Disconnect power, release Paging button, and reconnect power again.

Hope this will help.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-16-2020 08:59 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
RobertoDSM Offline
Junior Member
**

Posts: 9
Joined: Jan 2020
Reputation: 0
Post: #5
RE: W52p Repair
(01-16-2020 08:59 AM)complex1 Wrote:  Hi,

Please factory reset with following steps:
1. Disconnect power supply from base, but leave network cable connected
2. Long press Paging button on base, connect power supply, wait until all lights are on
3. Disconnect power, release Paging button, and reconnect power again.

Hope this will help.

Hi,
That doesn't work.
What else could i do?

Thank you for your help.
01-21-2020 04:00 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,509
Joined: Jan 2014
Reputation: 43
Post: #6
RE: W52p Repair
Hi,

If the handset is still connected to the base station, you can use it to find out the IP address.

Also do not use PoE, use external power supply instead.

Hope this will help.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
02-03-2020 07:43 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
RobertoDSM Offline
Junior Member
**

Posts: 9
Joined: Jan 2020
Reputation: 0
Post: #7
RE: W52p Repair
(02-03-2020 07:43 PM)complex1 Wrote:  Hi,

If the handset is still connected to the base station, you can use it to find out the IP address.

Also do not use PoE, use external power supply instead.

Hope this will help.

Hi,

That's the problem, the base doesn't even connect to the network and therefore it doesn't have an IP address.
And i don't use PoE.

Thank you.
02-05-2020 03:46 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,509
Joined: Jan 2014
Reputation: 43
Post: #8
RE: W52p Repair
(02-05-2020 03:46 PM)RobertoDSM Wrote:  
(02-03-2020 07:43 PM)complex1 Wrote:  Hi,

If the handset is still connected to the base station, you can use it to find out the IP address.

Also do not use PoE, use external power supply instead.

Hope this will help.

Hi,

That's the problem, the base doesn't even connect to the network and therefore it doesn't have an IP address.
And i don't use PoE.

Thank you.

Hi,

Assuming the handset is still registered to the Base then press OK button and select “Status” - “Base”.
Now you can read the IP-address (Base Firmware, MAC, Certificate, etc.) of the Base.
Use a PC, set his IP in the same range as the Base is and try to log into the Base.

BTW: What IP-address and firmware version do you read?

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
(This post was last modified: 02-05-2020 05:12 PM by complex1.)
02-05-2020 04:08 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
RobertoDSM Offline
Junior Member
**

Posts: 9
Joined: Jan 2020
Reputation: 0
Post: #9
RE: W52p Repair
(02-05-2020 04:08 PM)complex1 Wrote:  
(02-05-2020 03:46 PM)RobertoDSM Wrote:  
(02-03-2020 07:43 PM)complex1 Wrote:  Hi,

If the handset is still connected to the base station, you can use it to find out the IP address.

Also do not use PoE, use external power supply instead.

Hope this will help.

Hi,

That's the problem, the base doesn't even connect to the network and therefore it doesn't have an IP address.
And i don't use PoE.

Thank you.

Hi,

Assuming the handset is still registered to the Base then press OK button and select “Status” - “Base”.
Now you can read the IP-address (Base Firmware, MAC, Certificate, etc.) of the Base.
Use a PC, set his IP in the same range as the Base is and try to log into the Base.

BTW: What IP-address and firmware version do you read?

Hi,

The handset is always searching for base, and when I press OK button and select Status > Base, it shows zeros for everything.

Thank you.


Attached File(s) Thumbnail(s)
           
02-07-2020 10:05 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,509
Joined: Jan 2014
Reputation: 43
Post: #10
RE: W52p Repair
(02-07-2020 10:05 PM)RobertoDSM Wrote:  Hi,

The handset is always searching for base, and when I press OK button and select Status > Base, it shows zeros for everything.

Thank you.

Hmmm, then I'm afraid your Base is defect.
Please Submit a Ticket at Yealink Support. Maybe they can help you.
https://ticket.yealink.com/

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
02-08-2020 09:01 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  W52P not working after change of broadband supplier Jasibansel 1 514 01-22-2024 07:15 PM
Last Post: complex1
Sad W52P not picking up IP Burkni 4 4,158 09-19-2023 06:22 PM
Last Post: Burkni
  W56H with W52P Base dmvcomms 7 7,397 03-06-2023 04:39 PM
Last Post: poznaniak
  W73H handset with W52P problem reboot Paco Brufal 2 2,803 03-03-2023 01:21 AM
Last Post: nolto
  W52P Repeater RT10/rt20/RT30 schnell-yealink 3 8,650 04-20-2022 10:17 PM
Last Post: complex1
  W52P Firmware upgrade aunijaffer@gmail.com 5 12,334 09-07-2021 11:42 PM
Last Post: complex1
  W52P 2 handsets DAZZLING 1 6,941 06-01-2021 09:55 PM
Last Post: complex1
  W52P Openvpn with mikrotik info@quantiss.com 4 17,335 04-11-2021 06:25 AM
Last Post: Harms_Kubiak
  Is there no call history in web management panel in W52P? poznaniak 1 7,649 08-10-2020 12:49 PM
Last Post: complex1
  W52P factory reset without password ralph 1 9,546 04-02-2020 03:05 AM
Last Post: Yisroel_MongoTEL

Forum Jump:


User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication