[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Phone delayed sound after answering a call
Author Message
Jorge12 Offline
Junior Member
**

Posts: 4
Joined: Apr 2018
Reputation: 0
Post: #1
Phone delayed sound after answering a call
Hi, I have deployed around 20 t46's and each one of them have 8 active lines (accounts).

When a call comes in all the lines ring/light up.

When one of the users picks up the call, you can hear a very annoying sound coming from all the other phones, as if the phone was closing the calls, as if it was a low trilling sound.

The users find this very annoying.

How can I fix this?
02-13-2019 06:08 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jolouis Offline
Moderator
*****

Posts: 339
Joined: Oct 2013
Reputation: 6
Post: #2
RE: Phone delayed sound after answering a call
(02-13-2019 06:08 PM)Jorge12 Wrote:  When one of the users picks up the call, you can hear a very annoying sound coming from all the other phones, as if the phone was closing the calls, as if it was a low trilling sound.

That's a new one. What PBX/system are you connecting your phones to? Do the other phones remain idle when this happens, or does it look like they are active/answering also?...

Also, why did you setup 8 accounts on each phone? Usually using 1 account with call waiting is enough, just assign 8 line buttons to the same account to juggle the calls. Unless you really want 8 different extensions on each phone?....
02-13-2019 07:51 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Jorge12 Offline
Junior Member
**

Posts: 4
Joined: Apr 2018
Reputation: 0
Post: #3
RE: Phone delayed sound after answering a call
Sorry for the slow reply.

The phones need the 8 extensions because of the amount of call they get. So if I had all the Lines as say 200, only the first 200 would ring/light up and all ther lines would not see the incoming call, so the user wouldn't know if there was an incoming call.

Yes they would see it on the screen and hear the incoming call but they want to see it on the phone as a light instead. these are old ladies that are used to the old system.

This is a system that has a few people answering calls in different parts of the building, and in different levels, so like 6 users have to see all the incoming calls, and answer if available.

Hence the need to have a few accounts, so that they can see the incoming call, IF they are on a call already.

Maybe my implementation sux, but this is the only thing I could come up. Opened to suggestions by the way.

The system is running FPBXv13 and the issue, while annoying it might be easy to fix, which is the trilling ound of the accounts that did not pickup hanging up? I wouldnt know what that sound at the end is.
02-20-2019 05:55 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jolouis Offline
Moderator
*****

Posts: 339
Joined: Oct 2013
Reputation: 6
Post: #4
RE: Phone delayed sound after answering a call
(02-20-2019 05:55 PM)Jorge12 Wrote:  The phones need the 8 extensions because of the amount of call they get. So if I had all the Lines as say 200, only the first 200 would ring/light up and all ther lines would not see the incoming call, so the user wouldn't know if there was an incoming call.

?? Have you ever tested that? For example:
1) Configure a phone with say 3 line buttons. All three buttons are set to "Line 1" with a label of whatever the extension is.. say 200 as your example.
2) Make sure call waiting is enabled on your PBX.
3) When first call comes in, the first Line button lights up/flashes to show ringing. Display on the phone shows incoming caller information.
4) While on that call, if a second call is placed to extension 200, the 2nd button will begin to flash and the display will show the caller id of the new incoming call, below the existing call information. To answer that call, user just has to press the second line button.

So yes, technically not all 8 buttons would flash simultaneously, but there's also no reason for them to... a button will always flash to show an incoming call. (I'm assuming they came from an old KEY system where each physical line was mapped to a button. IN that case, only the line that was ringing would flash right?)

The only reason to do it the way you have done would be if you needed to have all 8 incoming lines kept completely separate from each other... so i.e. Line 1 is for Department A, Line 2 is Deparment B, etc. In that case, users would know what department is being called based on what line button is flashing.

Anyway all of that aside, the strange sound you are hearing doesn't seem normal. Can you record a video to demonstrate what exactly it is/what it sounds like? That would help track it down...
02-25-2019 02:14 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Phone message speed grstorga 0 353 04-08-2022 01:56 AM
Last Post: grstorga
  Phone A can reach Phone B, but Phone B cannot reach Phone A Reseau Web Plus 5 1,297 04-06-2022 11:03 PM
Last Post: complex1
  T46 - Program Message Button for a Help call? harrys 0 430 03-31-2022 11:08 PM
Last Post: harrys
  Paging to the phone coming through while on DND ahcomput_Support 7 2,047 03-26-2022 12:58 AM
Last Post: complex1
  Add the Remote Phone Book via a .cnf file sfrazier 6 2,167 02-04-2022 04:02 AM
Last Post: sfrazier
  Yealink T42S and T42G Phone stuck at Welcome Pierre06 7 3,894 01-10-2022 11:36 PM
Last Post: Pierre06
  Yealink T42G Phone stuck at Welcome LFC 8 18,768 11-18-2021 11:20 PM
Last Post: Pierre06
  Phone reboots and pauses on Initializing when PC port is used. gleblond 4 7,453 10-26-2021 03:17 AM
Last Post: gyegavian
  1 click entry to phone book Maciejp 0 1,414 08-10-2021 08:05 PM
Last Post: Maciejp
  Ended call still rings on receiver devices casi-online 2 3,161 08-05-2021 06:40 PM
Last Post: casi-online

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication