[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
CDP enable after factory reset cause the phone can't obtain IP address
Author Message
ccy Offline
Junior Member
**

Posts: 5
Joined: Dec 2014
Reputation: 0
Post: #1
CDP enable after factory reset cause the phone can't obtain IP address
I have a situation here after upgrading to latest V83 firmware on my T23G phone.

Previously, each time I reset to factory, the phone can obtain IP address from DHCP service without problem.

Recently, I discover that reset to factory, some phone can obtain IP address but some phone can't.

After further investigation, I notice those phone connect directly to core switch can get IP address. For those phone connect to access switch or nested switch, it can't get the IP address.

I further notice that if the cdp was enable in this new firmware. If I set the cdp enable to false explicitly after factory reset, I can get IP address for phones connected to access switch.

Please rectify this problem.

Thank you.
11-19-2018 06:28 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jolouis Offline
Moderator
*****

Posts: 339
Joined: Oct 2013
Reputation: 6
Post: #2
RE: CDP enable after factory reset cause the phone can't obtain IP address
Are you connecting phones to Cisco switches? If so, do you have CDP configured on your switches?

If setting CDP to disabled on the phone solves the problem, that is usually an indicator that you are using Cisco switches with default Voice VLAN/CDP advertising setup. If you do not want this/aren't using it, you should be turning it off on your switch, not relying on the phones to ignore it...
11-19-2018 10:03 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ccy Offline
Junior Member
**

Posts: 5
Joined: Dec 2014
Reputation: 0
Post: #3
RE: CDP enable after factory reset cause the phone can't obtain IP address
No. I am using Dell-x1052P as core switch and some mix managed or unmanaged switch as access switch.

Never aware the core switch has CDP option. Will try it later.
11-20-2018 12:49 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ccy Offline
Junior Member
**

Posts: 5
Joined: Dec 2014
Reputation: 0
Post: #4
RE: CDP enable after factory reset cause the phone can't obtain IP address
After a week of trial and error, no matter how I tweak the configuration, the phone will only obtain IP address with CDP disabled if it is connected to nested switch.
(It can obtain IP address successfully with CDP enabled only if connected to the main switch directly.)
I am not using a Cisco switch nor there is any Cisco devices in the network, so I decided to downgrade the firmware of the phone itself.

After downgrading to the previous firmware, even with CDP enabled by default, it is still able to obtain the IP address without any issues after factory reset or rebooting.
Current Firmware: T23-44.84.0.10.rom
Previous Firmware: T23-44.83.0.50.rom

Wish to know if this is a bug or intended behaviour.
Thank you.
11-29-2018 09:34 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jolouis Offline
Moderator
*****

Posts: 339
Joined: Oct 2013
Reputation: 6
Post: #5
RE: CDP enable after factory reset cause the phone can't obtain IP address
At this point if you have confirmed it's something that has changed in firmware you should probably open a support ticket for it, you will get better response from Yealink staff than here in the forums.
11-30-2018 02:34 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  MP54 factory reinstall ? zorgen 5 332 Yesterday 11:23 PM
Last Post: Yisroel_MongoTEL
  Yealink VOIP phone losing connection every few minutes robertpowell 1 133 03-27-2024 04:34 PM
Last Post: SRIIVF
  Yealink phone with hearing aids Jamie22RR 1 502 03-18-2024 01:49 AM
Last Post: complex1
  Yealink IP phone lesliefrench 0 436 01-25-2024 12:37 PM
Last Post: lesliefrench
  Remote Phonebook - Numbers Display Format On Phone Medryn 19 67,870 11-24-2023 02:28 AM
Last Post: shulem@theteklink.com
  IP Phone Login Error "ERR_INVALID_HTTP_RESPONSE" nolto 2 1,842 10-06-2023 04:34 PM
Last Post: nolto
  Multicast Stops Working until Phone Rebooted Blake1 10 11,179 09-21-2023 05:47 PM
Last Post: axiompm
  Is there a way to get the incoming caller phone number with an Action URI? troy44 1 1,189 09-04-2023 01:46 PM
Last Post: Regend_Yealink
  On MP50s responding to some phone trees ends the call TRK45 1 1,456 05-18-2023 04:46 PM
Last Post: complex1
  Import xml contacts to Yealink Phone upon provisioning via TFTP vusald 1 2,385 02-18-2023 06:30 PM
Last Post: complex1

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication