[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
T41 Park command.
Author Message
Chris Barron Offline
Member
***

Posts: 50
Joined: Sep 2015
Reputation: 0
Post: #1
T41 Park command.
Hi - on a t41 firmware 36.82.0.20 I have call park setup using the config below.

features.call_park.park_mode = 2
features.call_park.enable = 1
features.call_park.park_code = 700
features.call_park.park_retrieve_code = 701
linekey.4.type = 10
linekey.4.value = 701
linekey.4.label = P701
linekey.4.line = 1

when I attempt to retrieve a parked call from 701, the phone sends 700701.

It works Ok on 36.81.0.110.
10-25-2017 11:45 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
anonymous1711612242218
Unregistered

 
Post: #2
RE: T41 Park command.
Hi Chris,
Here's your configuration,

features.call_park.park_mode = 2
features.call_park.enable = 1
features.call_park.park_code = 700
features.call_park.park_retrieve_code = 701

You have already set the park value to 700 and retrieve value to 701,
but in the line key 4, you set the call park value to 701 again.

linekey.4.type = 10 (this key type means call park, not retrieve)
linekey.4.value = 701 (no need to fill in the value as you have already set the value previously)
linekey.4.label = P701
linekey.4.line = 1

You need to update the linekeys configuration as below,

linekey.2.type = 10 (config the linekey 2 as a park key)
linekey.2.line = 1
linekey.2.label = Park

linekey.3.type = 56 (config the linekey 3 as a retrieve key)
linekey.3.line = 1
linekey.3.label = Retrieve

Kind Regards
Samuel Wang
10-26-2017 10:03 AM
     Quote this message in a reply
Chris Barron Offline
Member
***

Posts: 50
Joined: Sep 2015
Reputation: 0
Post: #3
RE: T41 Park command.
Hi chaps, I thought that might be your response - however
a) the setup i need works ok on .110 firmware.
b) in Bicom/Asterisk we have to configure each retrieve key as type 10 otherwise its not active ie. park 1 = 701 park 2 = 702.

The problem only exists if I use the softkey 'park'
If I set a Blf key as type 10 and value 700 i can park a call - the pbx then chooses the first park slot e;g 701;

Assuming the softkey output is filtered via the phones dial plan i could possibly write a statement <7007:7> to strip off the unwanted 700.

Chris
10-31-2017 03:55 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
anonymous1711612242218
Unregistered

 
Post: #4
RE: T41 Park command.
Hi Chris,
This is your configuration,

features.call_park.park_mode = 2
features.call_park.enable = 1
features.call_park.park_code = 700
features.call_park.park_retrieve_code = 701
linekey.4.type = 10
linekey.4.value = 701
linekey.4.label = P701
linekey.4.line = 1

when you press linekey 4, it's type 10, pre-defined with park code 700, and also you specified the value 701 to this key, that's why it sends 700701.

If you wish to strip off the unwanted 700, you can leave the park code empty in below command,
features.call_park.park_code = 700 (leave this value blank)

Regards
Samuel
11-02-2017 02:41 AM
     Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  T48U BLF Park Call not working timotel 0 810 09-20-2023 07:20 AM
Last Post: timotel
  T43U T42S Call Park BLF robm 0 983 05-19-2023 12:16 AM
Last Post: robm
  cannot transfer to Park line button srcenturic 0 1,779 06-10-2022 01:41 AM
Last Post: srcenturic
  Call Park + Audible / Visual Alerts bdm 0 3,221 02-23-2021 04:24 AM
Last Post: bdm
  Call Park works on T22 but not a T42 tbolick 1 4,413 01-29-2021 10:19 PM
Last Post: Yisroel_MongoTEL
  Call Park Caller ID Mr 6 16,564 01-13-2020 08:40 PM
Last Post: AUXIUM_Support
  Caller ID display for HOLD and PARK Neutro 2 7,339 03-14-2019 07:27 PM
Last Post: Neutro
  "Park Button" Softkey Butters 1 9,328 06-08-2018 01:43 AM
Last Post: Travis_Yealink
  Call Park VOIP 2 7,316 04-19-2018 02:02 PM
Last Post: VOIP
  Call park option for in-call soft key keffa 8 20,136 01-25-2018 03:23 PM
Last Post: E123

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication