[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
T42G VLAN settings for PC VLAN
Author Message
Uwe Offline
Junior Member
**

Posts: 2
Joined: Aug 2017
Reputation: 0
Post: #1
T42G VLAN settings for PC VLAN
Hi,
we are new to Yealink phones. We want to use a T42G connected to VLAN 41 und thru the phone a PC connected to VLAN 31.

The Switches are HPE / aruba HP 2530-48G-PoEP Switch (J9772A)

the phone: Firmware Version 29.80.150.2
Hardware Version 29.1.0.0.0.0.0

We tried:
switchport VLAN 41 untagged, VLAN 31 tagged
switchport VLAN 41 tagged, VLAN 31 tagged
Phone:
WAN port disabled / enabled, VID 41
PC Port diesbled / enabled, VID 31

In some cases the PC gets a IP address from VLAN 41, or apipa address

In no config it gets an IP from VLAN 31.

What is the correct configuration on the switch and the phone?

Thanks
Uwe
(This post was last modified: 08-29-2017 11:53 AM by Uwe.)
08-29-2017 11:52 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Travis_Yealink Offline
Super Moderator
******

Posts: 171
Joined: Mar 2016
Reputation: 1
Post: #2
RE: T42G VLAN settings for PC VLAN
(08-29-2017 11:52 AM)Uwe Wrote:  Hi,
we are new to Yealink phones. We want to use a T42G connected to VLAN 41 und thru the phone a PC connected to VLAN 31.

The Switches are HPE / aruba HP 2530-48G-PoEP Switch (J9772A)

the phone: Firmware Version 29.80.150.2
Hardware Version 29.1.0.0.0.0.0

We tried:
switchport VLAN 41 untagged, VLAN 31 tagged
switchport VLAN 41 tagged, VLAN 31 tagged
Phone:
WAN port disabled / enabled, VID 41
PC Port diesbled / enabled, VID 31

In some cases the PC gets a IP address from VLAN 41, or apipa address

In no config it gets an IP from VLAN 31.

What is the correct configuration on the switch and the phone?

Thanks
Uwe

Hi Uwe,

Do you mean the network cable of PC is connected to the PC port of the phone?
What you want is phone and PC get IP address from different Vlan?

BR
Yealink_Travis
08-30-2017 03:19 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Uwe Offline
Junior Member
**

Posts: 2
Joined: Aug 2017
Reputation: 0
Post: #3
RE: T42G VLAN settings for PC VLAN
Yes,
the phone is connected at the Internet port to the switch, and the PC is connected to the PC port.

In the routing switch is ip helper configured, one config for each VLAN. when i set one port on the switch to VLAN 31 untagged and another port to VLAN 41 untagged and then I connect there devices, they get ip-addresses from the VLAN, e. g. 10.110.31.xxx and 10.110.41.xxx

But I don't know how to set the switch and the phone to do this. When it was not a yealink phone but a small manageble switch the I had to set VLAN 31 tagged and VLAN 41 untagged to this port, the switch would get 10.110.41.xxx as its address and I had to configure another port from the small switch as VLAN 31 untagged and the the device at this port would get 10.110.31.xxx as its address.

How can I make this work with the T42G? The T42G should get an IP address from thge VLAN 41 and the PC should get an IP address from VLAN 31.
(This post was last modified: 08-31-2017 08:45 AM by Uwe.)
08-31-2017 08:43 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jolouis Offline
Moderator
*****

Posts: 339
Joined: Oct 2013
Reputation: 6
Post: #4
RE: T42G VLAN settings for PC VLAN
(08-31-2017 08:43 AM)Uwe Wrote:  How can I make this work with the T42G? The T42G should get an IP address from thge VLAN 41 and the PC should get an IP address from VLAN 31.

Configure the switch port so that:
a) VLAN 41 is allowed as tagged
b) Untagged/default VLAN for the port is 31.

Then configure the T42G under advanced network settings to have VLAN ID of 41. Make sure Span to PC is disabled.

That should do it. When you power on the phone, all traffic from it will try to communicate on VLAN 41. When you plug any device into the PC port on the back of the phone, it will be passed to the switch untagged, and the switch will assign it/treat it as part of VLAN 31.
09-05-2017 09:58 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  T42G - Stuck at Welcome screen Maciejp 1 752 12-22-2023 01:47 AM
Last Post: complex1
  Model T42s and T42g, the speakerphone is enable on incoming calls Lissvazquez 6 2,721 07-28-2023 10:27 PM
Last Post: complex1
  Cannot export any files T42G Telcopc 1 2,275 10-07-2022 01:26 AM
Last Post: Telcopc
  Yealink T42G Phone stuck at Welcome LFC 12 30,269 08-08-2022 04:16 PM
Last Post: markvdheijden
  T43U LDAP Settings Not Working nolto 1 5,025 01-14-2022 07:03 PM
Last Post: nolto
  Yealink T42S and T42G Phone stuck at Welcome Pierre06 7 11,341 01-10-2022 11:36 PM
Last Post: Pierre06
  T42G - Stuck at Welcome screen clevoip 1 5,156 10-15-2021 01:28 AM
Last Post: complex1
  Missing Directory settings GroupOne_Support 1 6,096 08-17-2021 12:52 AM
Last Post: digiaustin
Bug Provision DialNow settings Maciejp 2 5,060 08-13-2021 01:23 PM
Last Post: Maciejp
  T46S Roaming settings UCUC 0 2,722 06-29-2021 06:44 PM
Last Post: UCUC

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication