[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
After firmware update (T46G), No Service, can't login
Author Message
Cory Offline
Junior Member
**

Posts: 6
Joined: Jan 2017
Reputation: 0
Post: #1
After firmware update (T46G), No Service, can't login
After attempting to load Firmware version T46-28.81.0.25 from Yealink's web site, 2 of my 5 phones I've tried updating are now unusable.

They rebooted and downloaded for about 20 minutes, but now, they say "No Service" , and I cannot log into them using either the default Yealink credentials or my Vonage credentials. Also, the firmware shows to be 28.81.193.15.

Why would this break my phones?
Why did the credentials change?
Why is the firmware shown on the phone screen higher than the firmware I downloaded?

What can I do to fix this?
I desperately need help.
Thank you.


Attached File(s) Thumbnail(s)
   
01-23-2017 05:22 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,258
Joined: Jan 2014
Reputation: 36
Post: #2
RE: After firmware update (T46G), No Service, can't login
Hi,

Let me try to help.

I’ve read both of your posts and I think your phones are connected to an RPS server because:
1. you cannot upgrade the firmware and if the firmware is upgraded then after a while it is reverted to the original firmware.
2. after a while (periodically re-provisioning by RPS server) the phones lost the (changed) settings and go back to default / predefined settings.
BTW: RPS stands for “Redirection and Provisioning Service”

If you want to unlock the phones I think you have to contact the provider who sold you the phones.

You can force the phone to reset to factory default by pressing the OK button for 10 sec, but I think the phone get the settings from the provider instead of the default settings.

Hope this helps.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-23-2017 07:03 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Cory Offline
Junior Member
**

Posts: 6
Joined: Jan 2017
Reputation: 0
Post: #3
RE: After firmware update (T46G), No Service, can't login
Thank you for the reply... but that's the problem.
Vonage sold us the phones and they're as confused as we are.

Due to a problem with our DSS keys partially losing configuration, Vonage suggested we upgrade the firmware found on Yealink's site using Yealink's procedure to do so.
3 of the 5 phones upgraded without issue... but 2 of them are in a state where they have login credentials neither us nor Vonage know. The phones all get IP addresses, but you can't log into them without the credentials to make any changes or do a factory reset.

Vonage is just as anxious for a fix as we are.

Any other suggestions? I really need to get these phones deployed.
01-23-2017 07:45 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,258
Joined: Jan 2014
Reputation: 36
Post: #4
RE: After firmware update (T46G), No Service, can't login
OK, please try next (is slight more than only one mouse click):
1. make sure your phones don’t have an internet connection, but leave them connected to your LAN.
2. reset the phones by press the OK button for 10 sec, the phone goes to factory default and after booting up it can’t connect to the RPS server because there is not internet connection, so it can’t download the provisioning file and you can login with the default password.
3. upgrade the firmware
4. factory reset the phone again
5. restore the internet connection.
6. check if everything is OK now.

Good luck.

I’m not 100% for sure if it is possible to upgrade the x.x.193.x firmware to the x.x.0.x firmware.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-23-2017 08:35 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Cory Offline
Junior Member
**

Posts: 6
Joined: Jan 2017
Reputation: 0
Post: #5
RE: After firmware update (T46G), No Service, can't login
Thank you for the information.
What finally worked was to do a forced reset by holding the speakerphone button while powering on... then power cycle without the network connected.
After that, we could login with default credentials... sounds similar to what you suggested.

Once they reset to factory, we could do a little with them (login), but they both still had some weird traits... so we installed the Yealink 28.81.0.25 firmware again to make them fresh.
That seems to have worked, so far.
01-23-2017 09:57 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,258
Joined: Jan 2014
Reputation: 36
Post: #6
RE: After firmware update (T46G), No Service, can't login
Sounds good.

Please keep us posted.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-23-2017 10:12 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Is it possible to pass logon credentials via the login URL ipcsolutions 2 592 05-12-2022 07:48 AM
Last Post: ipcsolutions
  Yealink T48s Firmware update failed dangmoss 2 2,248 02-19-2022 03:09 AM
Last Post: dangmoss
  Problem Change Firmware T48s from SFB to SIP Lars Maschke 2 2,458 01-14-2022 10:22 AM
Last Post: kumagera
  Feature Request T46G - Return to page 1 imfloridaguy 4 8,417 08-30-2021 12:34 AM
Last Post: eric@hudsonvalleygeek.com
  T46S Remote phonebook update to local phonebook. T9 Search UCUC 5 4,606 06-30-2021 02:50 PM
Last Post: UCUC
  T46G with EXP40 Sidecars Programming Burl 0 1,997 05-27-2021 11:35 PM
Last Post: Burl
  T43U random 'no service' Dario 1 2,800 05-19-2021 01:12 AM
Last Post: complex1
  Need to remove custom Fonality firmware 1CCT 16 26,235 05-03-2021 08:24 PM
Last Post: kmconklin
  SIP-T46s Bricked after latest firmware update. daniel.broome 2 4,771 04-27-2021 11:39 AM
Last Post: daniel.broome
  OEM Firmware change NotKnown 1 3,168 04-14-2021 07:41 PM
Last Post: complex1

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication