[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
T48G - busy tone for a second incomming call
Author Message
Dirk Offline
Junior Member
**

Posts: 5
Joined: Jan 2017
Reputation: 0
Post: #1
T48G - busy tone for a second incomming call
Hello,

I use a T48G with a Fritzbox 7490. If I´m at the telefone and a second call is comming in, I would like, that the person from the second call will here a busy tone and not a free line signal.

At the Fritzbox this is not adjustable (busy on busy), if you use an IP-phone.

So my question is - can I adjust the T48G, that the second caller will here a busy tone?

Thanks for your help in advance - Dirk
01-17-2017 09:10 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,549
Joined: Jan 2014
Reputation: 48
Post: #2
RE: T48G - busy tone for a second incomming call
Hi,

Please set both “Return Code When Refuse” and “Return Code When DND” to “486 (Busy Here)” and “180 Ring Workaround” to “Disabled” then try again.
Settings can be found in “Features > General Information”

Hope this helps.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-17-2017 12:03 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Dirk Offline
Junior Member
**

Posts: 5
Joined: Jan 2017
Reputation: 0
Post: #3
RE: T48G - busy tone for a second incomming call
Hi,

sorry, no changes - there is still comming in the second call with a free linde signal.

Here are my settings:

Thanks Dirk


Attached File(s) Thumbnail(s)
       
01-17-2017 01:10 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,549
Joined: Jan 2014
Reputation: 48
Post: #4
RE: T48G - busy tone for a second incomming call
Please set "Call Waiting" to "Enable"

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-17-2017 01:26 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Dirk Offline
Junior Member
**

Posts: 5
Joined: Jan 2017
Reputation: 0
Post: #5
RE: T48G - busy tone for a second incomming call
With enabeling "Call Waiting" the second call gets still a free sign and I cann see the second incomming call on the display.
After hanging up I get the information about one missing call.

Any other idea?
01-17-2017 01:55 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,549
Joined: Jan 2014
Reputation: 48
Post: #6
RE: T48G - busy tone for a second incomming call
Please check if "Call Waiting Tone" is "Enabled" (Features > Audio)

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-17-2017 02:22 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Dirk Offline
Junior Member
**

Posts: 5
Joined: Jan 2017
Reputation: 0
Post: #7
RE: T48G - busy tone for a second incomming call
Yes, it is....


Attached File(s) Thumbnail(s)
   
01-17-2017 02:24 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Dirk Offline
Junior Member
**

Posts: 5
Joined: Jan 2017
Reputation: 0
Post: #8
RE: T48G - busy tone for a second incomming call
Yes, "Call Waiting Tone" was "Enabled" - so there is still the same problem that a second incomming call gets a free line signal.

Any other idea?

Thanks
Dirk
01-17-2017 04:34 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
complex1 Offline
3CX Adv. Cert. Engineer
*****

Posts: 1,549
Joined: Jan 2014
Reputation: 48
Post: #9
RE: T48G - busy tone for a second incomming call
Hi,

I do not have a FritzBox or familiar with it, so I have register my T48G directly to my VoIP Provider.
Before I did the test I set “Call Waiting” to “Disabled”
All other settings in the Features tab are untouched and remain the same.
Then I make a call to the T48G and accept it.
Then I make a second call to the T48G and get/hear a busy sound.
So if you set “Call Waiting” to “Disabled” it should also work for you.
If not, then I think you FritzBox is doing something what you don’t want it to do.

Kind regards,
Frank.

I am not an employee of Yealink.
Dutch is my native language, not English. Apologies for my imperfect grammar.
Please do not send unsolicited PM messages. I will not answer them.
01-17-2017 05:36 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  LDAP directory during call transfers aciacci 0 708 06-20-2024 11:19 PM
Last Post: aciacci
  No dial tone when connecting calls internally tvettel 0 1,014 04-17-2024 02:20 PM
Last Post: tvettel
  [Post info updated] Always ask where the call forwarding goes ivan2808 0 1,011 04-10-2024 10:16 PM
Last Post: ivan2808
  permisson to Call list on t46S ist denied wolfi30 1 1,593 03-04-2024 02:08 PM
Last Post: wolfi30
  permission denied to call list wolfi30 0 1,096 02-23-2024 08:54 PM
Last Post: wolfi30
  MP54 Call Forwarding pureit2018 0 1,670 11-23-2023 07:58 AM
Last Post: pureit2018
  Enhanced DSS Key - Conference Call joe1st 0 1,445 11-11-2023 05:27 AM
Last Post: joe1st
  Unable to Answer call without pressing Line 1 TheKirbyGroup 0 1,677 11-03-2023 11:04 PM
Last Post: TheKirbyGroup
  Yealink T28 setup audible ring on 2nd incoming call JeffWilkinson 20 96,191 10-18-2023 12:59 PM
Last Post: sles
  Picking up a call does not display Caller's Name oliv 0 2,313 04-19-2023 04:25 PM
Last Post: oliv

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication