[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
W52P auto provision
Author Message
ECN Offline
Junior Member
**

Posts: 3
Joined: May 2015
Reputation: 1
Post: #1
W52P auto provision
Hi,

I'm using the W52P cordless phone with option 66 pointing to the host-name of an internal TFTP server. The W52P is able to download its common configuration file but fails to download the mac.cfg file. The phones logs indicate the following error:

Quote:Jun 13 03:26:57 LIBD[345]: TFTP<5+notice> tftp open begin, host: -host name removed-, port:69, remote_name:001565858fe9.cfg
Jun 13 03:26:57 LIBD[345]: TFTP<6+info > Send Request Packet
Jun 13 03:26:57 LIBD[345]: TFTP<5+notice> tftp open success
Jun 13 03:27:02 LIBD[345]: TFTP<3+error > Error Select! errno 0
Jun 13 03:27:02 ATP [345]: ATP <3+error > tftp to file failed, code = -8, msg = Read Error, retry = 3
Jun 13 03:27:02 ATP [345]: ATP <4+warnin> Download mac.cfg fail
Jun 13 03:27:02 ATP [345]: ATP <6+info > send end provision!!

I've tried renaming the mac.cfg file that is currently on my tftp server to match what the phone is looking for - 001565858fe9.cfg - but this hasn't resolved the issue. I've stripped the config in the mac.cfg file to the bare basics in an attempt to make troubleshooting easier:

Quote:#!version:1.0.0.1

##File header "#!version:1.0.0.1" can not be edited or deleted.##

################################################################################​#######
## Account1 Settings ##
################################################################################​#######

#Enable or disable the account 1; 0-Disabled (default), 1-Enabled;
account.1.enable = 1

#Configure the label displayed on the LCD screen for account 1.
account.1.label = 101

#Configure the display name of account 1.
account.1.display_name = 101

#Configure the username and password for register authentication.
account.1.auth_name = 101
account.1.password = -removed-

#Configure the register user name.
account.1.user_name = 101

#Configure the SIP server address.
account.1.sip_server_host = -removed-

#Specify the IP address or domain name of the outbound proxy server.
account.1.outbound_host = -removed-

#Specify the port for the SIP server. The default value is 5060.
account.1.sip_server_port = 5060

#Specify the server port, the default value is 5060.
account.1.outbound_port = 5060

#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
{if $sip_transport_1 == 'udp'}account.1.transport = 0{/if}
{if $sip_transport_1 == 'tcp'}account.1.transport = 1{/if}
{if $sip_transport_1 == 'tls'}account.1.transport = 2{/if}
{if $sip_transport_1 == 'dns srv'}account.1.transport = 3{/if}

#Configure the SIP port for account 1, the default value is 5060.
account.1.sip_listen_port = 5060

#Configure the register expiry time (in seconds), the default value is 3600.
account.1.expires = 3600

#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
account.1.ptime = 20

The handset and base station are using out of the box firmware. Absolutely no upgrades have been done at this point in time to either.


My question here is why does the W52P fail to download the mac.cfg file?
06-13-2015 12:00 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ECN Offline
Junior Member
**

Posts: 3
Joined: May 2015
Reputation: 1
Post: #2
RE: W52P auto provision
A more specific question;

I'm trying to download the mac.cfg file via http. The path is specified via the common configuration file with the following line:

#Configure the URL of the auto provisioning server.
auto_provision.server.url = http://host-name/file-location

is anyone able to confirm if they've had success downloading the mac.cfg file using this line in the common configuration file using http?
06-16-2015 02:18 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Elaine_Yealink Offline
Super Moderator
******

Posts: 152
Joined: Aug 2014
Reputation: 4
Post: #3
RE: W52P auto provision
Hi Sean,

Please pay attention to my email feedback. Just in case, please pay attention to the FAQ attached.

Regards
Elaine


Attached File(s)
.docx  Auto Provision Twice in Chain .docx (Size: 25.53 KB / Downloads: 47)
06-16-2015 05:34 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ECN Offline
Junior Member
**

Posts: 3
Joined: May 2015
Reputation: 1
Post: #4
RE: W52P auto provision
Hi Elaine,

Thank you VERY much, this is exactly what I was looking for. The mac.cfg file now downloads using HTTP as I would like it to. Please pass on my sincere thanks to the support team.

kind regards,
ECN
06-17-2015 01:27 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
Question "Trusted Certificates" and auto provisioning jobst 3 868 06-15-2022 11:00 AM
Last Post: dbonnell
Wink Auto Provsioning EOL products and devices that do dont have recent firmware releases GalacticSolutions 1 1,075 04-17-2022 07:05 AM
Last Post: markm
  Auto Provision Wall Paper Stopped Working TRP Tech 4 3,834 11-19-2021 10:27 AM
Last Post: TRP Tech
  DO NOT Provision / Update Firmware looker44 2 4,065 08-17-2021 04:44 AM
Last Post: looker44
  Step by Step for Auto Provisioning nguyenp 2 5,982 08-06-2021 04:27 PM
Last Post: Phil2021
  Auto-Provision W60P on FreeSWITCH Phoneperson 10 17,057 03-06-2021 03:51 AM
Last Post: Phoneperson
  Factory Reset via Provision Andrews1 3 8,127 07-02-2019 03:09 PM
Last Post: Fraukas2
  Auto provisioning seams to be (partly) broken in version 83 for T46G HaraldL 2 8,192 07-02-2019 03:04 PM
Last Post: Fraukas2
Lightbulb Auto provision firmware ... Yuriy Y. 1 6,113 04-26-2019 05:40 AM
Last Post: Yuriy Y.
  T22P always auto restart jamess2007 2 6,353 03-13-2019 11:49 AM
Last Post: Langveldt

Forum Jump:


User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication