(02-20-2018 10:58 AM)complex1 Wrote: (02-19-2018 04:32 PM)Geckoo Wrote: (04-29-2015 05:14 AM)Yealink_Flora Wrote: yes, please use features.config_dsskey_length=1 and let me know if any question.
im unable to find it on the config template for 3cx? can you tell me were i can find it?
Yes, it is there.
If you run 3CX v15.5 SP3 you can find this parameter in the 3CX template under “Phone Features”
im unable to find it.
Code:
#######################################################################################
## Phone Features ##
#######################################################################################
#Enable or disable the phone to escape the pound key as percent sign followed by 23 when dialing out; 0-Disabled, 1-Enabled (default);
sip.use_23_as_pound =
sip.send_response_by_request =
sip.notify_reboot_enable =
#The following parameters only applicable to V80
sip.disp_incall_to_info =
sip.limit_server_name =
sip.limit_server_reason =
sip.tls_listen_port =
sip.trust_ctrl =
sip.timer_t1 =
sip.timer_t2 =
sip.timer_t4 =
custom.features.redial_via_local_sip_server.enable = 1
features.redial_via_local_sip_server.enable = 1
sip.terminate_notify_sub_delay_time =
sip.bind_local_addr_enable =
sip.user_agent_prefix =
##It is XSI authentication mode.0-Disable 1-Enable
sip.authentication_for_xsi = 0
##It is DSS KEY to call park type, whether the trigger BLF function.It takes effect after a reboot.
##The default value is 0-Disable(DSS KEY to call park type,triggering BLF function) 1-Enable
sip.call_park_without_blf = 0
##It is ASCII conversion into corresponding symbols.
##The defalult value is blank. 0-Disable 1-Enable
sip.escape_characters.enable =
##The default value is 0 ( said according to the transmission mode configured to listen on port),1-
##1-said at the same time to monitor TCP and UDP
##2-said to monitor TCP and UDP at the same time, and from the BLF - the LIST to subscribe to the contact with a transport = TCP parameters
sip.listen_mode = 0
##The default value is 0-Disable, 1-Enable.It takes effect after a reboot.
##0-registered according to the uri of the tectonic refer - by domain
##1-according to refer the from header fields to construct refer - by domain
sip.refer_by_header_auto_build = 0
##The default is blank.The Valid characters are digits - _.! ~ * # '() & Q462 = + R452 $,;?/ \ 0
##It is username needs to be preserved in a special notation.
sip.reserve_characters =
##The default value is 0.(contracting out the random contact, via port to carry fixed port).It takes effect after a reboot.
##1-the out-contracting port random contact, via port to carry
##2-the out-contracting ports fixed contact, via carry fix
sip.tcp_port_random_mode = 1
sip.tls_port_random = 1
#Enable or disable the RFC2543 Hold feature; 0-Disabled (default), 1-Enabled;
sip.rfc2543_hold = 0
##V81NEW##
sip.requesturi.e164.addglobalprefix=
sip.skip_redundant_failover_addr=
sip.request_validation.source.list=
sip.request_validation.digest.list=
sip.request_validation.digest.realm=
sip.request_validation.digest.realm=
sip.cid_source.preference=
sip.dns_transport_type=
sip.sdp_early_answer_or_offer=
sip.reliable_protocol.timerAE.enable=
##Send MAC address in UA.0-Disable 1-Enable(00:11:22:33:44:55) 2-Enable(001122334455)
sip.mac_in_ua = 2
#account.1.sip_server.Y.invite_retry_counts=
#account.1.sip_server.Y.only_signal_with_registered=
account.1.reg_failed_retry_min_time=
account.1.reg_failed_retry_max_time=
account.1.line_seize.expires=
account.1.gruu.enable=
account.1.sip_server.Y.failback_subscribe.enable=
account.1.hold_use_inactive=
[/code]
Found it, there are actually two parts of the phone features
(rond line 1600 and 1900) let see of it works.
i changed the value to 20 and i didnt work, ill try it with a factory reset of the phone and the value set to 1
Yeah worked! thanks !
