[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
phone stating in LLDP that it is half duplex
Author Message
mikes Offline
Junior Member
**

Posts: 24
Joined: Nov 2014
Reputation: 0
Post: #1
phone stating in LLDP that it is half duplex
I have issues with T4X series phones showing in their LLDP they send to the Ethernet switch that they are half duplex. Both the phones WAN port and the Ethernet switch are set for Auto Negotiate. I see the same in the LLDP if both the phone and the Ethernet switch are set to 100 M full duplex. The phone I tested with is a T41P Firmware Version 36.71.19.6 and Hardware Version 36.0.0.0.0.0.0. I am troubleshooting a delay audio issue and want to clear up this apparent mismatch so as to eliminate it being the cause.

Here is the output of the switches debug of LLDP.

2015.04.15 04:01:42 : LLDP: giga-swx 0/19: RX LLDPDU from 00:0A:6B:03:B3:E1 len
= 198
2015.04.15 04:01:42 : LLDP: Chassis ID (Network Address) "192.168.21.125"
2015.04.15 04:01:42 : LLDP: Port ID (MAC Address) "00:0A:6B:03:B3:E1"
2015.04.15 04:01:42 : LLDP: Neighbor Port ID: 00:0A:6B:03:B3:E1 on
2015.04.15 04:01:42 : LLDP: TTL 180
2015.04.15 04:01:42 : LLDP: System Name "T4X_SPI"
2015.04.15 04:01:42 : LLDP: System Description "36.71.19.6"
2015.04.15 04:01:42 : LLDP: System Capabilities:
Bridge, Router, Telephone
Enabled System Capabilities:
Bridge, Telephone
2015.04.15 04:01:42 : LLDP: Port Description "WAN PORT"
2015.04.15 04:01:42 : LLDP: Negotiation Status: "enabled"
LLDP: Speed/Duplex: "100M/half-duplex"
2015.04.15 04:01:42 : LLDP: LLDP-MED Capabilities:
Other, Repeater, Router, Telephone
LLDP: Application/VLAN ID/CoS/DSCP: Voice/4/5/46 (tagged)

2015.04.15 04:01:42 LLDP LLDP: Speed Duplex mis-match on giga-swx 0/19. Speed/D
uplex: "100M/full-duplex" Neighbor Speed/Duplex: "100M/half-duplex"
04-15-2015 08:29 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
James_Yealink Offline
Administrator
*******

Posts: 1,159
Joined: Aug 2014
Reputation: 8
Post: #2
RE: phone stating in LLDP that it is half duplex
Hi Mikes,

Our tech support guys for Tardian will contact you.

Regards,
James
04-16-2015 06:13 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
mikes Offline
Junior Member
**

Posts: 24
Joined: Nov 2014
Reputation: 0
Post: #3
RE: phone stating in LLDP that it is half duplex
(04-16-2015 06:13 PM)Yealink_James Wrote:  Hi Mikes,

Our tech support guys for Tardian will contact you.

Regards,
James

When Should I expect them to contact me?
(This post was last modified: 04-21-2015 09:16 PM by mikes.)
04-21-2015 09:15 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
James_Yealink Offline
Administrator
*******

Posts: 1,159
Joined: Aug 2014
Reputation: 8
Post: #4
RE: phone stating in LLDP that it is half duplex
Sorry mike,

I have sent a mail to urge our guys working on Tardian firmware.
They should contact you 22th April BeiJing time.

Regards,
James
04-22-2015 12:23 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
mikes Offline
Junior Member
**

Posts: 24
Joined: Nov 2014
Reputation: 0
Post: #5
RE: phone stating in LLDP that it is half duplex
(04-22-2015 12:23 AM)Yealink_James Wrote:  Sorry mike,

I have sent a mail to urge our guys working on Tardian firmware.
They should contact you 22th April BeiJing time.

Regards,
James

The "guys working on Tadiran firmware" have not contacted me. When should I expect them to do so?
(This post was last modified: 04-24-2015 08:33 PM by mikes.)
04-24-2015 08:31 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
James_Yealink Offline
Administrator
*******

Posts: 1,159
Joined: Aug 2014
Reputation: 8
Post: #6
RE: phone stating in LLDP that it is half duplex
Hi Mike,

Very sorry. They are leaving for anual trip these days and will back on next Monday.
I just check in a T41 with V73 firmware. It seems that phone send a correct capability. Not quite sure whether it's an issue in firmware 36.71.19.6.

.... .1.. .... .... = 100BASE-TX (full duplex mode): Capable
.... 1... .... .... = 100BASE-TX (half duplex mode): Capable
...0 .... .... .... = 100BASE-T4: Not capable
..1. .... .... .... = 10BASE-T (full duplex mode): Capable
.1.. .... .... .... = 10BASE-T (half duplex mode): Capable
0... .... .... .... = Other or unknown: Not capable

May I know who direclty sell phone to you? Maybe you can also contact them for an instant support. Our guys will check the issue in Monday.

Regards,
James
(This post was last modified: 04-24-2015 11:41 PM by James_Yealink.)
04-24-2015 11:41 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
mikes Offline
Junior Member
**

Posts: 24
Joined: Nov 2014
Reputation: 0
Post: #7
RE: phone stating in LLDP that it is half duplex
(04-24-2015 11:41 PM)Yealink_James Wrote:  Hi Mike,

Very sorry. They are leaving for anual trip these days and will back on next Monday.
I just check in a T41 with V73 firmware. It seems that phone send a correct capability. Not quite sure whether it's an issue in firmware 36.71.19.6.

.... .1.. .... .... = 100BASE-TX (full duplex mode): Capable
.... 1... .... .... = 100BASE-TX (half duplex mode): Capable
...0 .... .... .... = 100BASE-T4: Not capable
..1. .... .... .... = 10BASE-T (full duplex mode): Capable
.1.. .... .... .... = 10BASE-T (half duplex mode): Capable
0... .... .... .... = Other or unknown: Not capable

May I know who direclty sell phone to you? Maybe you can also contact them for an instant support. Our guys will check the issue in Monday.

Regards,
James

Tadiran Telecom sells to us directly.

Here is the output of the switch "sh lldp neighbors detail" It shows the phone Speed/duplex: 100baseTXHD. I have contacted Tadiran and they say it is a Yealink issue. Yealink generates the software for them. How is the phone performance being impacted by operating at half duplex?

Chassis ID: 192.168.21.121 (Network Address)
System Name: T4X_SPI
Device Port: 00:0A:6B:03:B3:E3 (MAC Address)
TTL: 166
Capabilities: Bridge, Router, Telephone
Enabled Capabilities: Bridge, Telephone
Local Port: giga-swx 0/7
Management Addresses:
Auto-negotiation: enabled
Speed/duplex: 100baseTXHD
LLDP-MED Enabled Capabilities:
Capabilities, Network Policy, ExtendedPD, Inventory
LLDP-MED Network Policy:
Application - Voice
Cos/DSCP - 6/46
VLAN ID - 4 (tagged)

Please have someone test the version I am using. 5/5/15

Thank you Mike
(This post was last modified: 05-06-2015 12:25 PM by mikes.)
05-06-2015 12:18 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
mikes Offline
Junior Member
**

Posts: 24
Joined: Nov 2014
Reputation: 0
Post: #8
RE: phone stating in LLDP that it is half duplex
(05-06-2015 12:18 PM)mikes Wrote:  
(04-24-2015 11:41 PM)Yealink_James Wrote:  Hi Mike,

Very sorry. They are leaving for anual trip these days and will back on next Monday.
I just check in a T41 with V73 firmware. It seems that phone send a correct capability. Not quite sure whether it's an issue in firmware 36.71.19.6.

.... .1.. .... .... = 100BASE-TX (full duplex mode): Capable
.... 1... .... .... = 100BASE-TX (half duplex mode): Capable
...0 .... .... .... = 100BASE-T4: Not capable
..1. .... .... .... = 10BASE-T (full duplex mode): Capable
.1.. .... .... .... = 10BASE-T (half duplex mode): Capable
0... .... .... .... = Other or unknown: Not capable

May I know who direclty sell phone to you? Maybe you can also contact them for an instant support. Our guys will check the issue in Monday.

Regards,
James

Tadiran Telecom sells to us directly.

Here is the output of the switch "sh lldp neighbors detail" It shows the phone Speed/duplex: 100baseTXHD. I have contacted Tadiran and they say it is a Yealink issue. Yealink generates the software for them. How is the phone performance being impacted by operating at half duplex?

Chassis ID: 192.168.21.121 (Network Address)
System Name: T4X_SPI
Device Port: 00:0A:6B:03:B3:E3 (MAC Address)
TTL: 166
Capabilities: Bridge, Router, Telephone
Enabled Capabilities: Bridge, Telephone
Local Port: giga-swx 0/7
Management Addresses:
Auto-negotiation: enabled
Speed/duplex: 100baseTXHD
LLDP-MED Enabled Capabilities:
Capabilities, Network Policy, ExtendedPD, Inventory
LLDP-MED Network Policy:
Application - Voice
Cos/DSCP - 6/46
VLAN ID - 4 (tagged)

Please have someone test the version I am using. 5/5/15

Thank you Mike

So is this a firmware issue? If it is, can Yealink please inform Tadiran Telecom of it so they can get updated firmware? I still have no resolution to the my issue. Mike Schrader 5/17/2015 7:06 pm PST
(This post was last modified: 05-18-2015 09:46 AM by mikes.)
05-18-2015 09:43 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
mikes Offline
Junior Member
**

Posts: 24
Joined: Nov 2014
Reputation: 0
Post: #9
RE: phone stating in LLDP that it is half duplex
(05-18-2015 09:43 AM)mikes Wrote:  
(05-06-2015 12:18 PM)mikes Wrote:  
(04-24-2015 11:41 PM)Yealink_James Wrote:  Hi Mike,

Very sorry. They are leaving for anual trip these days and will back on next Monday.
I just check in a T41 with V73 firmware. It seems that phone send a correct capability. Not quite sure whether it's an issue in firmware 36.71.19.6.

.... .1.. .... .... = 100BASE-TX (full duplex mode): Capable
.... 1... .... .... = 100BASE-TX (half duplex mode): Capable
...0 .... .... .... = 100BASE-T4: Not capable
..1. .... .... .... = 10BASE-T (full duplex mode): Capable
.1.. .... .... .... = 10BASE-T (half duplex mode): Capable
0... .... .... .... = Other or unknown: Not capable

May I know who direclty sell phone to you? Maybe you can also contact them for an instant support. Our guys will check the issue in Monday.

Regards,
James

Tadiran Telecom sells to us directly.

Here is the output of the switch "sh lldp neighbors detail" It shows the phone Speed/duplex: 100baseTXHD. I have contacted Tadiran and they say it is a Yealink issue. Yealink generates the software for them. How is the phone performance being impacted by operating at half duplex?

Chassis ID: 192.168.21.121 (Network Address)
System Name: T4X_SPI
Device Port: 00:0A:6B:03:B3:E3 (MAC Address)
TTL: 166
Capabilities: Bridge, Router, Telephone
Enabled Capabilities: Bridge, Telephone
Local Port: giga-swx 0/7
Management Addresses:
Auto-negotiation: enabled
Speed/duplex: 100baseTXHD
LLDP-MED Enabled Capabilities:
Capabilities, Network Policy, ExtendedPD, Inventory
LLDP-MED Network Policy:
Application - Voice
Cos/DSCP - 6/46
VLAN ID - 4 (tagged)

Please have someone test the version I am using. 5/5/15

Thank you Mike

So is this a firmware issue? If it is, can Yealink please inform Tadiran Telecom of it so they can get updated firmware? I still have no resolution to the my issue. Mike Schrader 5/17/2015 7:06 pm PST

Yealink has confirmed that this is a bug in all T4x Tadiran branded firmware. A correction will come in the next firmware version. Mike Schrader 5/21/2015 5:51 am PST
(This post was last modified: 05-21-2015 08:32 PM by mikes.)
05-21-2015 08:30 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
voip_customer Offline
Junior Member
**

Posts: 1
Joined: Aug 2015
Reputation: 0
Post: #10
RE: phone stating in LLDP that it is half duplex
Hi All,
I have the T41P in our network and running firmware version 36.71.0.66 connected to cisco switches 2960x PoE and the switches have LLDP enabled on all ports.
The issue is the ip phones T41P are randomly rebooting
Some one have the same problem? the version 36.71.0.66 is compatible LLDP?

Best Regards
(This post was last modified: 08-26-2015 08:06 PM by voip_customer.)
08-26-2015 08:01 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Yealink VOIP phone losing connection every few minutes robertpowell 1 84 03-27-2024 04:34 PM
Last Post: SRIIVF
  Yealink phone with hearing aids Jamie22RR 1 496 03-18-2024 01:49 AM
Last Post: complex1
  Yealink IP phone lesliefrench 0 434 01-25-2024 12:37 PM
Last Post: lesliefrench
  Remote Phonebook - Numbers Display Format On Phone Medryn 19 67,850 11-24-2023 02:28 AM
Last Post: shulem@theteklink.com
  IP Phone Login Error "ERR_INVALID_HTTP_RESPONSE" nolto 2 1,834 10-06-2023 04:34 PM
Last Post: nolto
  Multicast Stops Working until Phone Rebooted Blake1 10 11,159 09-21-2023 05:47 PM
Last Post: axiompm
  Is there a way to get the incoming caller phone number with an Action URI? troy44 1 1,187 09-04-2023 01:46 PM
Last Post: Regend_Yealink
  On MP50s responding to some phone trees ends the call TRK45 1 1,452 05-18-2023 04:46 PM
Last Post: complex1
  Import xml contacts to Yealink Phone upon provisioning via TFTP vusald 1 2,378 02-18-2023 06:30 PM
Last Post: complex1
  W60B - URL for Remote Phone Book Bosstoad 2 2,939 01-06-2023 02:58 AM
Last Post: Bosstoad

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication