[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Trying to unbrick base.
Author Message
SimonB Offline
Junior Member
**

Posts: 2
Joined: Dec 2014
Reputation: 0
Post: #1
Brick Trying to unbrick base.
I had a problem where the phone stopped working. My first step was to reboot the base, but once it was powered back up, the handset couldn't find it and I couldn't access the web admin UI.

I checked my router, and it did not appear to be taking an IP address from the DHCP server.

To try and bring it back to life, I followed the recovery guide I found on this forum, (via Tftpd32). However if I power up the basestation, only the power LED is lit and it does not obtain an IP address (as shown in the "DHCP Server" tab in Tftpd32).

If I power up the basestation while holding down the paging button, all three LED's light up and I see W5X.bin and W5X.rfs get transferred:

Code:
Connection received from 192.168.0.100 on port 1142 [30/12 15:53:57.069]
Read request for file <W5X.bin>. Mode octet [30/12 15:53:57.069]
OACK: <timeout=5,blksize=1468,> [30/12 15:53:57.069]
Using local port 61578 [30/12 15:53:57.069]
<W5X.bin>: sent 1032 blks, 1514044 bytes in 0 s. 0 blk resent [30/12 15:53:57.849]
Connection received from 192.168.0.100 on port 2047 [30/12 15:53:57.989]
Read request for file <W5X.rfs>. Mode octet [30/12 15:53:57.989]
OACK: <timeout=5,blksize=1468,> [30/12 15:53:57.989]
Using local port 58749 [30/12 15:53:57.989]
<W5X.rfs>: sent 5715 blks, 8388608 bytes in 5 s. 0 blk resent [30/12 15:54:02.279]

However the "DHCP Server" tab still doesn't show anything and the W52P.rom file is not transferred.
12-31-2014 05:24 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
James_Yealink Offline
Administrator
*******

Posts: 1,159
Joined: Aug 2014
Reputation: 8
Post: #2
RE: Trying to unbrick base.
Hi Simon,

Can you have a try of hard reset.

1. Disconnect the power adapter.
2. Long press the paging key and reconnect the power adapter.
When base station finishes reset, the power indicator LED, network status LED and registtration LED illuminate in sequence. System PIN and all individual setting are reset to factory defaults.

When you do a facotory reset the DHCP server and TFTP server are set up in a same PC or two PC?

Regards,
James
12-31-2014 02:31 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
SimonB Offline
Junior Member
**

Posts: 2
Joined: Dec 2014
Reputation: 0
Post: #3
RE: Trying to unbrick base.
Thanks for your reply.

I tried a hard reset and it makes no difference (it doesn't pick up an IP address).

For the attempted reset, I have the DHCP server and TFTP server on the same PC.
01-06-2015 11:30 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  internal call between two base stations fails janus 1 4,699 01-07-2021 07:20 PM
Last Post: complex1
  Can't de-register default base Nigutz 9 26,535 07-15-2019 09:11 PM
Last Post: GregoireG
  double base station proximity ipv6fill 2 8,095 03-21-2017 08:39 AM
Last Post: Kevin_Yealink
  New Handset Can't Register to Base SergioA 2 10,253 01-06-2017 06:20 PM
Last Post: SergioA
  Searching for Base aabramov 63 183,292 10-17-2016 10:43 AM
Last Post: Karl_Yealink
  Downgrading Base firmware to 25.73.0.27 from 25.73.0.40 bharat@metro 3 12,808 07-20-2016 08:53 PM
Last Post: complex1
  W52P Base default password under FW 26.73.0.11 ? voicewarellc 2 14,351 04-19-2016 07:21 AM
Last Post: VK2XXY
  Provision second W52H to existing base and 3cx vondie 10 45,358 02-26-2016 04:46 AM
Last Post: GreyFox
  Searching for Base gyegavian 1 6,797 01-12-2016 05:34 AM
Last Post: Klaus_Yealink
  Where can I buy a base station on its own? jofa 1 6,656 01-11-2016 06:12 PM
Last Post: Karl_Yealink

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication