[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
New parameter features.call_park.park_mode = 0 in local configuration on upgrade
Author Message
ipcsolutions Offline
Member
***

Posts: 57
Joined: Jun 2015
Reputation: 2
Post: #1
New parameter features.call_park.park_mode = 0 in local configuration on upgrade
On upgrade (I think only on T46G) to .130 (could be earlier releases), the configuration features.call_park.park_mode = 0 is set in local configuration.
By default call_park.park_mode = 2 so this breaks most Call Park implementations.
Once removed from Local Configuration, features.call_park.park_mode = 2 and everything works fine.

Can this problem please be fixed.

Thanks
Mike
(This post was last modified: 10-10-2016 05:30 PM by ipcsolutions.)
10-10-2016 05:20 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Kevin_Yealink Offline
Administrator
*******

Posts: 204
Joined: Jul 2016
Reputation: 2
Post: #2
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade
(10-10-2016 05:20 PM)ipcsolutions Wrote:  On upgrade (I think only on T46G) to .130 (could be earlier releases), the configuration features.call_park.park_mode = 0 is set in local configuration.
By default call_park.park_mode = 2 so this breaks most Call Park implementations.
Once removed from Local Configuration, features.call_park.park_mode = 2 and everything works fine.

Can this problem please be fixed.

Thanks
Mike

Hi Mike

This is Kevin from yealink support team, nice to know you.

For this issue, can you tell me the firmware of the phone, and the earlier firmware.

Becase in the 28.80.0.130, then value is 2 by default. For the broad firmware, it is 0 by default.

BR
Kevin
10-11-2016 03:04 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ipcsolutions Offline
Member
***

Posts: 57
Joined: Jun 2015
Reputation: 2
Post: #3
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade
I suspect that the earlier firmware was T46-28.80.0.95 and I upgraded to T46-28.80.0.130.

Thanks
Mike
10-12-2016 07:29 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Kevin_Yealink Offline
Administrator
*******

Posts: 204
Joined: Jul 2016
Reputation: 2
Post: #4
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade
(10-12-2016 07:29 AM)ipcsolutions Wrote:  I suspect that the earlier firmware was T46-28.80.0.95 and I upgraded to T46-28.80.0.130.

Thanks
Mike

Hi I test in my side , and the park mode on .130 firmware is 2 by default. So please check if you enable broadsoft in the .95.

BR
Kevin
10-13-2016 04:40 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ipcsolutions Offline
Member
***

Posts: 57
Joined: Jun 2015
Reputation: 2
Post: #5
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade
Unfortunately I cant confirm what it was previously so this could have been the issue. I will monitor on the next lot of phones I install.

Thanks
Mike
10-13-2016 06:09 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Kevin_Yealink Offline
Administrator
*******

Posts: 204
Joined: Jul 2016
Reputation: 2
Post: #6
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade
(10-13-2016 06:09 PM)ipcsolutions Wrote:  Unfortunately I cant confirm what it was previously so this could have been the issue. I will monitor on the next lot of phones I install.

Thanks
Mike

Hi Mike

Let me know if any update.
BR
Kevin
10-14-2016 06:44 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ipcsolutions Offline
Member
***

Posts: 57
Joined: Jun 2015
Reputation: 2
Post: #7
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade
Hi Kevin

I can confirm that all phones I have installed straight out of the box (T41 & T46) when upgraded to 0.130 have features.call_park.park_mode = 0 is set in local configuration.
This is really annoying as I need to remove it manually from the Web GUI for all phones. Can I remove it a different way?
11-08-2016 10:10 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  T48U Custom Firmware Upgrade to Official Friendly 0 1,928 03-29-2023 01:20 AM
Last Post: Friendly
  Enhanced BLF and PBX configuration pavel.patera 0 1,086 12-09-2022 09:43 PM
Last Post: pavel.patera
  T42s VPN & local SIP Accounts noch work, only one of them mysterox 0 1,450 10-27-2022 04:54 PM
Last Post: mysterox
  T46S will not upgrade 79schultz 1 2,299 10-12-2022 03:11 AM
Last Post: complex1
  T46S Remote phonebook update to local phonebook. T9 Search UCUC 5 8,636 06-30-2021 02:50 PM
Last Post: UCUC
  EHS36 Not answering / upgrade lonvoice 7 9,801 03-09-2021 09:46 PM
Last Post: Yisroel_MongoTEL
  Phone features not working KenleyHickman 10 18,065 09-14-2020 07:52 PM
Last Post: KenleyHickman
  Local and Remote phonebooks with more than 3 #s per entry? AndyInNJ 1 5,076 04-04-2020 09:29 AM
Last Post: complex1
  Local and Remote phonebooks pause and code (conference bridges) AndyInNJ 0 3,087 04-03-2020 06:02 PM
Last Post: AndyInNJ
  SpeedDial a contact from local directory Simatics 1 4,537 01-21-2020 11:46 AM
Last Post: anonymous1711612242218

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication