[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
3CX and T46G
Author Message
grayhawk Offline
Junior Member
**

Posts: 2
Joined: Dec 2014
Reputation: 0
Post: #1
3CX and T46G
We are running the latest version of 3CX (v12 SP6.1) running on Yealink T46G firmware version 28.71.0.224

We are having major issues our headsets(AmTech AT3085 Monaural and multiple Plantronics headsets) The send volume on the microphones is just to high. It distorts and the patients either hang up or get extremely upset. We were forced to stop using the headsets.

I have been told by our vendor to change the custom template in 3CX (which isn't supported) under "Voice". I have tried every setting and nothing helped.

I have also been told to add the following lines under "Voice" in the template:

#Configure the sending volume of Speaker, Handset and Headset. It ranges from 1 to 53, the default values are 25, 35, 29.
#Require reboot;
voice.handfree_send =25
voice.handset_send = 35
voice.headset_send = 29

Editing the voice.headset_send down to around 10 or 12 seemed to fix our problem, but this isn't supported. If we have ANY issues 3CX will not support us due to a custom template being in place. Also this "fix" wasn't even in the original template so I am a little concerned about issues that these entries will cause.

Can anyone point me in a direction that will be supported?
12-10-2014 04:59 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
James_Yealink Offline
Administrator
*******

Posts: 1,159
Joined: Aug 2014
Reputation: 8
Post: #2
RE: 3CX and T46G
Hi Gray,

You can refer to this post:
http://forum.yealink.com/forum/showthread.php?tid=2423

The default send value of T4x is 1.

So these parameter should be changed like below in template:
voice.handfree_send = 1
voice.handset_send = 1
voice.headset_send = 1

Regards,
James
12-10-2014 09:57 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
grayhawk Offline
Junior Member
**

Posts: 2
Joined: Dec 2014
Reputation: 0
Post: #3
RE: 3CX and T46G
Thanks for reply.

After reading through the link you provided, it seems I have no options except to edit the custom template. This is unfortunate due to the fact that if I have ANY issues that requires 3CX support I am in trouble. They have already told me on numerous occasions that they won't even help troubleshoot an issue until I remove the custom template.
(This post was last modified: 12-10-2014 12:55 PM by grayhawk.)
12-10-2014 12:54 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
tsukraw Offline
Member
***

Posts: 145
Joined: Jan 2014
Reputation: 3
Post: #4
RE: 3CX and T46G
With 3CX support you just have to be firm with your issue and be 100% positive yourself that the issue is not caused by a modification you did.

If you are not sure you always have the option of taking a test phone or two and setting the back to the default template to verify the issue still happens before calling support.

We have dozens of 3CX customers out there and just about every single one of them is running on modified templates. There is a lot of things you can do my modifying templates but there is a lot you can muck up at the same time.

You have to look at 3CX's angle on it as well. They cannot possibly support from there size every feature/modification that Yealink allows you to make for there phones. There is a list a mile long. So 3CX support has to draw the line somewhere.

But like i said if you set one single phone back to the default template test confirm the issue still exists you will be golden with support. That is how we do it and have no issues at all.

As for your echo issue those values will absolutely correct the problem with the headset.
Take a look at this post.
http://forum.yealink.com/forum/showthread.php?tid=2423
If you need any help or unsure of what you are doing PM me. Would gladly give you a hand.
(This post was last modified: 12-23-2014 01:11 PM by tsukraw.)
12-23-2014 01:11 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
CWR Offline
Moderator
*****

Posts: 717
Joined: May 2013
Reputation: 7
Post: #5
RE: 3CX and T46G
I could not imagine not being able to have a customized template... what an administrative nightmare that would be.

Craig Reilly
MCSA, 3cx Advanced Certified
Scottsdale, AZ
12-24-2014 03:41 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Change standard outgoing line on T46G oestersund 1 6,490 12-15-2018 09:58 PM
Last Post: support2
Bug T46g & T48G RADIUS 802.1x and SHA256 Bigmac 22 56,289 08-13-2017 07:54 PM
Last Post: MiKeDaDoC
  T46G: How to deactivate Live Dialpad totally? Werner1959 6 16,357 03-05-2017 08:21 PM
Last Post: Werner1959
  T46G with exp40 Paulo Batista 2 8,963 11-06-2016 01:57 AM
Last Post: CWR
  T46G eaches only incoming calls, no outgoing calls Ddorf 2 8,249 10-27-2016 12:46 AM
Last Post: anonymous1711612242218
  T46G Hostname not registering on DHCP fraukas 2 12,564 10-27-2016 12:34 AM
Last Post: anonymous1711612242218
  T46G Issues Save Volume settings + BLF pickup Jeroen 3 13,787 08-31-2016 02:47 AM
Last Post: CWR
  [SOLVED] T46G one way audio on outgoing calls Kamik 3 12,994 08-16-2016 06:22 PM
Last Post: Kamik
  T46G Power Saving Paulo Batista 1 7,091 08-14-2016 12:47 AM
Last Post: PavlovsPuppy
  401/403 authorization error on remote asterisk from T46G over VPN hexhex 1 10,264 07-06-2016 02:10 AM
Last Post: hexhex

Forum Jump:


User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication