[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Re-order Hanset
Author Message
Offline
Junior Member
**

Posts: 16
Joined: Jul 2014
Reputation: 0
Post: #1
Re-order Hanset
Hi,

I was experiencing a problem due to Hanset register order. We use autoprovisioning to configure user accounts and set it to one handset.
We do like the following:
Account 1 -> H1
Account2 -> H2
.
.

This works fine until we need to deregister one of the handsets.
E.g. One client has 4 handsets each one with one account if I delete H2 I will configure Account1 to 3 but with our autoprovision one of the accounts will be unavailable because Account3 -> H3 that does not exist.
I tried factory reset on both base and handset but without success, H4 is allways H4. Is there any way to change this?

Best Regards
12-05-2014 10:59 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink_Jim Offline
Super Moderator
******

Posts: 127
Joined: Aug 2014
Reputation: 2
Post: #2
RE: Re-order Hanset
Hi
You can try to delete H4 and register again. Or you can try to set up as below to check if it can solve this isue:

Login to the web UI, Go to aAccount-> Number Assignment

[img]http://forum.yealink.com/forum/attachment.php?aid=1213[/img


Attached File(s) Thumbnail(s)
   
12-08-2014 10:34 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Offline
Junior Member
**

Posts: 16
Joined: Jul 2014
Reputation: 0
Post: #3
RE: Re-order Hanset
Hi Jim,

I tried to delete H4 and also do factory reset, but whenever I register again the handset it comes with H4, not H2.

I know that I can solve this trough WebUI, it was what I did for test purposes, but how can this be done using only auto-provisioning?
I am using V50, but we are planning to deploy v73. Could this be a bug of v50?

Thanks!
12-09-2014 10:53 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink_Jim Offline
Super Moderator
******

Posts: 127
Joined: Aug 2014
Reputation: 2
Post: #4
RE: Re-order Hanset
Hi,
Given below is the configuration parameters base on V73:

-------------------------------------------------------------------------------------
#!version:1.0.0.1
#The line accept to incoming(1,2,3,4,5);X ranges from 1 to 5
#handset.X.incoming_lines = 1,2,3,4

handset.1.incoming_lines =

#The line accept to call out(1,2,3,4,5)
#handset.X.dial_out_lines = 1,2,5
#handset.X.dial_out_default_line = 1

handset.1.dial_out_lines =
handset.1.dial_out_default_line =

handset.1.name =
----------------------------------------------------------------------

Please go to below link to get the V73 configuration template:

ftp://Jim:v2R88xcL@ftp.yealink.com/Auto%...ning/W52P/

Hope this helps!
12-10-2014 09:28 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication