New Forum system requires email address which you used to apply for your account to replace your original username. Password stays the same.Please see this post for more details
http://forum.yealink.com/forum/showthread.php?tid=40344

Yealink Test Club has been officially launched. Please visit post below to get detail information. Come and join us!
http://forum.yealink.com/forum/announcements.php?aid=18

We just had the YMCS online and we are also working on the features plan on the future versions, in this regard we are need to hear your voice about the YMCS.
Please visit : http://forum.yealink.com/forum/showthread.php?tid=42322


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
T46G Issues Save Volume settings + BLF pickup
Author Message
Jeroen Offline
Junior Member
**

Posts: 12
Joined: May 2014
Reputation: 0
Post: #1
T46G Issues Save Volume settings + BLF pickup
Hello I have currently 2 issues with out T45G phones

Setting
- Firmware 28.72.188.13
- 3cx V12 PBX
- manual provisioning

1) I have configured some DSSKeys to have a blf. In the Extension field I put the default pickup code for 3cx (= *20* ) to be able to also pick the line up, but it does not seem to work.
It does dial the associated Extention, but it refuses to add the pickup code

2) I am looking for a way to save the Volume settings of the T46G. so that after a reboot, the ringtones are not to loud.

I searched the forum and Google, but could not find a solution yet.
Thanks in advance
11-17-2014 05:48 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
coco Offline
Super Moderator
******

Posts: 113
Joined: Aug 2014
Reputation: 0
Post: #2
RE: T46G Issues Save Volume settings + BLF pickup
Hello Jeroen,

1) Could you please tell me whether you can successfully pickup the call via pressing the red flashing BLF key ?
If yes , then you have correctly configured.
As you mentioned:"It does dial the associated Extention, but it refuses to add the pickup code"
I would like to tell you if there is no call to the monitored number, then the status of the corresponding BLF key stay in green . At that time , the BLF key is equal to Speed dial key. And it will not add the pickup code when you press it.
2)Please try to provision the phone via below syntax.
voice.ring_vol = Integer from 1 to 15
It configures the volume of ringer. The default value is 8.
Please refer to the Auto Provision Guide for details.

Thx
(This post was last modified: 11-18-2014 08:15 PM by coco.)
11-18-2014 08:13 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Jeroen Offline
Junior Member
**

Posts: 12
Joined: May 2014
Reputation: 0
Post: #3
RE: T46G Issues Save Volume settings + BLF pickup
Thanks for your answer Coco,

1)
The BLF is configured correctly as far as i know. , and if the phone of the target rings, the blf indeed flashes red. If he talkis it is continious red, and if there is no action on the target phone the led is just continiously green.

This is how i configured the dds key on the test phone to be able to pickup my calls.
[Image: DDSKEY.png]
When i try topick it up while it flashes red, i just see the phone trying to dial the etension number witch results in a "line busy" message

Just to be clear I also allready played arround with different values in both the Value field and the extension field:
*20* && 202
202 && *20*
202 && *20*202
*20*202 && 202

Note: *20* is the default pickup code for the 3CX pbx. If i dail itmanually while the led flashes red, I can pick the line up.

2) Sadly, due to multiple accounts and the lack of support for 3cx PBX, I have to configure all phones manually. However I guess i could create a default provisioning, safe it, and then add the stuff i am not able to add to the auto provisioning files


(11-18-2014 08:13 PM)Yealink_Coco Wrote:  Hello Jeroen,

1) Could you please tell me whether you can successfully pickup the call via pressing the red flashing BLF key ?
If yes , then you have correctly configured.
As you mentioned:"It does dial the associated Extention, but it refuses to add the pickup code"
I would like to tell you if there is no call to the monitored number, then the status of the corresponding BLF key stay in green . At that time , the BLF key is equal to Speed dial key. And it will not add the pickup code when you press it.
2)Please try to provision the phone via below syntax.
voice.ring_vol = Integer from 1 to 15
It configures the volume of ringer. The default value is 8.
Please refer to the Auto Provision Guide for details.

Thx
11-18-2014 08:41 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ModCraig Offline
Moderator
*****

Posts: 716
Joined: May 2013
Reputation: 7
Post: #4
RE: T46G Issues Save Volume settings + BLF pickup
In the WebGUI check out the FEATURES TAB - then CALL PICKUP.
The Pickup code should be here and enabled.
You can also set an audible alert (beep) or visual alert (on your phone screen).
Then in your screen shot image - the VALUE and EXTENSION would both be the same.
(Its been a while since I set this up - but this should put you in the right direction)

Craig Reilly
MCSA, 3cx Advanced Certified
Scottsdale, AZ
08-31-2016 02:47 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Voicemail Settings on T46S lansend 2 1,215 02-07-2019 02:33 PM
Last Post: jolouis
  Change standard outgoing line on T46G oestersund 1 927 12-15-2018 09:58 PM
Last Post: support2
  T48S SfB Config Settings Reverting Aaron_IT 1 1,446 01-04-2018 11:00 AM
Last Post: Paul_Yealink
  BLF/DSS key settings VG 2 2,990 09-30-2017 08:16 PM
Last Post: rpenrod
Bug T46g & T48G RADIUS 802.1x and SHA256 Bigmac 22 18,192 08-13-2017 07:54 PM
Last Post: MiKeDaDoC
  Directed Call pickup Caller ID Casey Roll 6 6,644 05-27-2017 10:42 AM
Last Post: Jensen_Yealink
  Lock ring volume Gabriel.Syr 4 7,044 03-10-2017 06:37 PM
Last Post: Patrick Hogan
  T46G: How to deactivate Live Dialpad totally? Werner1959 6 5,763 03-05-2017 08:21 PM
Last Post: Werner1959
  Missed Calls messages after pickup and in queues Kamik 2 3,809 12-14-2016 07:05 PM
Last Post: nick.spannagel
  T46G with exp40 Paulo Batista 2 3,260 11-06-2016 01:57 AM
Last Post: ModCraig

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication