[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.

Post Reply 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
W52W/P battery and PIN issues
Author Message
michael.gath Offline
Junior Member

Posts: 9
Joined: Jul 2014
Reputation: 0
Post: #1
W52W/P battery and PIN issues
Just purchased and tried setting up a new W52P w / 5 ea W52H .
Updated the firmware: Base ( Handset ( .
Battery idle life is <6 hr. After three tries to update the Firmware I was lucky to get 30 min.
I cannot register the handset or any of the settings because the default PIN (0000)
returns "Incorrect Pin". I have yet to find any like references to these issue and was hoping someone might be of help.
Thanks in advance.
Michael Gath
08-11-2014 09:00 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Nology_Support Offline
Junior Member

Posts: 9
Joined: Jun 2014
Reputation: 0
Post: #2
RE: W52W/P battery and PIN issues
Hi Michael,

You were lucky to get 30 min of Idle time? Talk-time?

I would recommend you Factory Reset, The handsets as well and try registering again.

Recommended time to charge the handsets is 6Hrs, that should give you optimal results...or at least better than 6hrs.
There is a firmware update coming out soon apparently that will address battery issues.

08-26-2014 10:38 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply

Post: #3
RE: W52W/P battery and PIN issues
Hello michael.gath,

If you forget the pin code, pls refer to the following steps to do the hardrest to get the pin code back to '0000'.
1. Let the base disconnect the power adapter. (PS: Now the network cable is connected with the base.)
2. Long press the paging key and reconnect the power adapter.
When base station finishes reset, the power indicator LED, network status LED and registration LED illuminate in sequence.
3. After the led illuminate in sequence, then disconnect power adatper again.
4. Then connect the base with power adapter. Wait for about 3-5 minutes for the base to recover.

Or you can refer to the following link for help as well.
08-29-2014 03:10 PM
     Quote this message in a reply
Post Reply 

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  W52P - Extension Dialing Issues adam.comws 2 8,800 04-07-2017 12:34 PM
Last Post: jolouis
  W52P Reliability issues - Initializing data chrisdixon2 3 12,208 12-23-2016 01:46 AM
Last Post: Elaine_Yealink
  Battery life very poor Charliestott 7 27,193 11-15-2016 10:12 PM
Last Post: tritch
  W52P Web interface issues yealinknewb 1 6,868 03-10-2016 06:13 PM
Last Post: Klaus_Yealink
  Multicast Paging Issues voicearray 4 13,864 10-17-2015 02:49 AM
Last Post: joshua@itstel.com
  w52p Paging issues paulhuynh 3 11,497 09-13-2014 10:41 AM
Last Post: Yealink_Jim
  Handset low battery akarpov 18 51,868 06-27-2014 06:22 PM
Last Post: anonymous1715181860335
  Ring back, call waiting, firmware issues johan 1 8,302 05-26-2014 06:14 PM
Last Post: Yealink Support

Forum Jump:

User(s) browsing this thread:

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication