[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
T28P & T38G: Speed Dial delay or pause between DTMF
Author Message
Rogier Offline
Junior Member
**

Posts: 1
Joined: Jan 2017
Reputation: 0
Post: #61
RE: T28P & T38G: Speed Dial delay or pause between DTMF
I got it to work today with the help of our vendor. Thought i'd share with you how this is done, cause apparently it was already possible on our firmware for over a year. (v80).

We have the T48G.

* Login to your telephone directly by pointing your browser to its IP address. (so not use the provisional landing page (first mistake i made)).
* Go to DSS keys
* Create new speeddial entry
* Everything that is not the primary phone number needs to be put in the extension Field (so not in the Value field).
* Use <#> as the pause sign, where # needs to be replaced by the number of seconds you would like to wait. So you would use "<5>" for 5 seconds...


So if would like to dial my conference bridge at "123123123" and then wait for 4 seconds and then dial extension 567567#: i would put "123123123"in the value field, and "<4>567567#" in the extension field.

NOt sure if this works for all your phones, but you could give it a try.

Best, Rogier
01-24-2017 02:49 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
tim942 Offline
Junior Member
**

Posts: 2
Joined: Dec 2015
Reputation: 0
Post: #62
RE: T28P & T38G: Speed Dial delay or pause between DTMF
(01-24-2017 02:49 PM)Rogier Wrote:  * Go to DSS keys
* Create new speeddial entry
* Everything that is not the primary phone number needs to be put in the extension Field (so not in the Value field).
* Use <#> as the pause sign, where # needs to be replaced by the number of seconds you would like to wait. So you would use "<5>" for 5 seconds...

I couldn't get this working in v80, but I got it working in v81:

1. Enable EDK in config file (no UI enable at this time)
2. select the DSS key type "Custom Key"
3. Enter the macros with the numbers in the values. Example: 1231231234$Cwc$$Cp3$123$Tdtmf$

$Cwc$ - Macro to wait until call is connected before continuing
$Cp#$ - Macro to wait for # seconds
$Tdtmf$ - Macro to submit the preceding numbers in dtmf (123 in this case)

Right now, this only works as the Custom Key in DSS. If we can get this setup in the Address Book, I can get my users out of my hair over this.
05-05-2017 04:37 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
ClueStumpy Offline
Junior Member
**

Posts: 1
Joined: Oct 2017
Reputation: 0
Post: #63
RE: T28P & T38G: Speed Dial delay or pause between DTMF
(05-05-2017 04:37 PM)tim942 Wrote:  1. Enable EDK in config file (no UI enable at this time)
2. select the DSS key type "Custom Key"
3. Enter the macros with the numbers in the values. Example: 1231231234$Cwc$$Cp3$123$Tdtmf$

Right now, this only works as the Custom Key in DSS. If we can get this setup in the Address Book, I can get my users out of my hair over this.

Us too. We need to be able to add these entries to the remote XML phonebook in our T46S phones, but it doesn't seem to be supported. For example, this should work but doesn't:

<?xml version="1.0" encoding="UTF-8"?>
<YealinkIPPhoneBook>
<Title>Yealink</Title>
<Menu Name="Headquarters">
<Unit Phone1="8001234567" Name="Main Number" />
<Unit Phone1="8001234567$Cwc$$Cp3$1111" Name="John" />
<Unit Phone1="8001234567$Cwc$$Cp3$2222" Name="Bob" />
<Unit Phone1="8001234567$Cwc$$Cp3$333" Name="Susan" />
</Menu>
</YealinkIPPhoneBook>
11-01-2017 06:05 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
mcbsys Offline
Junior Member
**

Posts: 5
Joined: Feb 2017
Reputation: 0
Post: #64
RE: T28P & T38G: Speed Dial delay or pause between DTMF
(02-27-2013 08:13 PM)Yealink Support Wrote:  Hello,
Do you mean in the DSS key value, you want to fill two number? Dial one first, and then dial another one if the first one didn't answer?
Sorry currently we can just fill one number in the speed dial key.
Could you let us know the scenarios application? And which phone can support this?

Paul Test
11-29-2018 06:34 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
DavidAUM Offline
Junior Member
**

Posts: 8
Joined: Apr 2013
Reputation: 0
Post: #65
RE: T28P & T38G: Speed Dial delay or pause between DTMF
I have a regular conference call that uses the same dial-in number and PIN for access. I would love to be able to set up one speed-dial listing to handle this repetitive task.

The pattern to replicate is the dialing of a specific ten-digit number, pausing two seconds, then dialing a 9-digit PIN followed by a # sign.

I have not been able to work the needed pause into a speed-dial listing on its own.

Right now, I have the 10-digit number in a speed-dial. I hit that first and then, after 2 seconds, I have the 9-digit Pin + # assigned as DTMF to a DSS key that I press.

It works, but my T22P phone only has three DSS keys so this is not an optimal solution. It also makes distributing this functionality around the office much more difficult than it needs to be.

It just doesn't seem to work in the 7.73.0.50 firmware available for the T22P.

The phone continues to work fine except for the EOL status placed on it by Yealink.
11-29-2018 08:13 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
mcbsys Offline
Junior Member
**

Posts: 5
Joined: Feb 2017
Reputation: 0
Post: #66
RE: T28P & T38G: Speed Dial delay or pause between DTMF
(05-05-2017 04:37 PM)tim942 Wrote:  
(01-24-2017 02:49 PM)Rogier Wrote:  * Go to DSS keys
* Create new speeddial entry
* Everything that is not the primary phone number needs to be put in the extension Field (so not in the Value field).
* Use <#> as the pause sign, where # needs to be replaced by the number of seconds you would like to wait. So you would use "<5>" for 5 seconds...

I couldn't get this working in v80, but I got it working in v81:

1. Enable EDK in config file (no UI enable at this time)
2. select the DSS key type "Custom Key"
3. Enter the macros with the numbers in the values. Example: 1231231234$Cwc$$Cp3$123$Tdtmf$

$Cwc$ - Macro to wait until call is connected before continuing
$Cp#$ - Macro to wait for # seconds
$Tdtmf$ - Macro to submit the preceding numbers in dtmf (123 in this case)

Right now, this only works as the Custom Key in DSS. If we can get this setup in the Address Book, I can get my users out of my hair over this.
Very helpful, thanks. I was able to program automatic voicemail retrieval. I wish it would work in the Account > Advanced > Voice Mail field so the user could use the envelope icon rather than a DSS key to retrieve voicemail. Blogged:

https://www.mcbsys.com/blog/2018/11/use-...link-t42g/
11-29-2018 08:53 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
SCPCJNR Offline
Junior Member
**

Posts: 11
Joined: Oct 2017
Reputation: 0
Post: #67
RE: T28P & T38G: Speed Dial delay or pause between DTMF
THANKS for that Rogier! Got it to work, had to put <12>258# in the Extension field to make the delay long enough. Much obliged!!!
04-01-2019 02:05 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jolouis Offline
Moderator
*****

Posts: 339
Joined: Oct 2013
Reputation: 6
Post: #68
RE: T28P & T38G: Speed Dial delay or pause between DTMF
(05-20-2019 09:34 AM)BhenChod Wrote:  One Last Thing Not being able to program a pause in a dial string is a huge disadvantage to my users and a feature that could easily be implemented.

As tim942 pointed out above, you can do this on speed dial/BLF keys by using EDK. What is not supported is doing it within the phone book/directory entries. From your description it sounds like you want the former so there should be no issues making that happen.
05-22-2019 02:01 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
HotlineExperts Offline
Junior Member
**

Posts: 1
Joined: Aug 2019
Reputation: 0
Post: #69
RE: T28P & T38G: Speed Dial delay or pause between DTMF
Hi all;

Does anyone know how to add a PAUSE in a Dial plan/Replace Rule?

Thanks
08-18-2019 09:06 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  set number key as speed dial key not working timotel 1 1,954 08-27-2024 04:18 AM
Last Post: Yisroel_MongoTEL
  FreePBX chan_pjsip DTMF digits not displaying on screen karl_edgeconnect 1 1,536 02-13-2024 09:52 PM
Last Post: karl_edgeconnect
  Audio Delay - Disable Jitter Buffer? joni1802 4 4,663 07-17-2023 10:20 PM
Last Post: complex1
  MP54 Handset - Auto Dial on handset pickup/Off Hook TheGarrison 5 9,689 09-16-2022 03:04 AM
Last Post: imgibason
  Click to dial from web browser h2g-vaka 7 18,586 06-10-2022 03:27 AM
Last Post: troy44
  Dial Shortcut from Directory customvoip 0 3,229 09-29-2021 05:46 AM
Last Post: customvoip
  T28p - Firmware version advice Tato 2 16,006 09-11-2020 01:04 PM
Last Post: Tato
Brick Yealink t29G | 5 seconds ring delay amichy 2 11,080 08-31-2020 11:08 PM
Last Post: gmanual
  Slow speed on the PC port Sur 4 18,275 04-12-2019 09:28 AM
Last Post: Johnny88
  Dial from Windows Pox 0 4,995 11-06-2018 02:52 PM
Last Post: Pox

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication