[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
t46 disconnects phone call when it receives a page.
Author Message
jasit Offline
Member
***

Posts: 85
Joined: Mar 2013
Reputation: 0
Post: #1
t46 disconnects phone call when it receives a page.
Our user with a T46 running 28.72.0.2 is on a phone call and then a page comes over using multicast paging and his phone will disconnect the current call. here are the multicast paging settings we use, any idea what we need to change?


#Enbale or diable the phone to handle the incoming multicast paging calls when there is a multicast paging call on the phone; 0-Disabled, 1-Enabled (default);
#If enabled, the phone will answer the incoming multicast paging call with a higher priority and ignore that with a lower priority.
multicast.receive_priority.enable = 1

#Configure the priority of multicast paging calls. It ranges from 0 to 10.
multicast.receive_priority.priority =

#Configure the listening multicast IP address and port number for the phone. X ranges from 1 to 10.
#multicast.listen_address.X.ip_address =
multicast.listen_address.1.ip_address =224.0.0.32:10000

#Configure the lable displayed on the LCD screen when receiving the multicast paging. X ranges from 1 to 10.
#multicast.listen_address.X.label =
multicast.listen_address.1.label = Office Page
06-20-2014 03:56 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,684
Joined: Dec 2012
Reputation: 24
Post: #2
RE: t46 disconnects phone call when it receives a page.
Hi jasit ,

1. Do you leave multicast.receive_priority.priority = as default vlaue 10 ?
2. Please try "multicast.receive_priority.enable = o" and test again.
06-20-2014 02:13 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
blendedtech Offline
Junior Member
**

Posts: 4
Joined: Aug 2014
Reputation: 0
Post: #3
RE: t46 disconnects phone call when it receives a page.
I ran across this same situation and these two settings fixed it.

multicast.receive_priority.enable = 0
multicast.receive_priority.priority = 0

Thanks to Yealink Support for the answer.

-Eric

(06-20-2014 02:13 PM)Yealink Support Wrote:  Hi jasit ,

1. Do you leave multicast.receive_priority.priority = as default vlaue 10 ?
2. Please try "multicast.receive_priority.enable = o" and test again.
08-20-2014 01:53 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
Brick MP50 stuck after call transfer af@benenden.school 4 1,174 12-22-2021 07:24 PM
Last Post: af@benenden.school
  MP50 won't initiate a call on a Mac (Big Sur) computer? microdaft 1 1,195 11-21-2021 07:17 PM
Last Post: georgedendle
  MP50 Phone: Won't hang-up microdaft 2 1,920 11-19-2021 01:23 AM
Last Post: tpackrat
  Cannot disable audible Park notifications during active call livehappy42 3 1,150 11-13-2021 09:11 AM
Last Post: livehappy42
  MP56 - Speaker Phone Quality UBYeah 4 1,823 11-05-2021 12:32 AM
Last Post: Jeff.Petit
  T57W Call Park Alert bcramer 1 2,227 10-29-2021 05:33 AM
Last Post: livehappy42
Sad T22P No Sound on Call Pick Up oaltinsoy853 1 1,063 10-19-2021 07:22 PM
Last Post: complex1
  SIP Phone VP59 recovery ERROR sakovalev 0 1,126 08-19-2021 10:07 PM
Last Post: sakovalev
  T58 Call Park and Transfer Problems user42491 1 1,695 08-03-2021 09:24 PM
Last Post: complex1
  T58A SCA Shared Call Appearance with Call Manager cm_y 1 4,113 11-15-2019 09:42 AM
Last Post: Jacky_Yealink

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication