[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Autoanswer on click to dial feature
Author Message
Walter
Unregistered

 
Post: #1
Autoanswer on click to dial feature
Dear Support,
could you tell me how does the autoanswer feature on T26, T38, W52 and VP530 work?
My SIP server is able to send an header invite customized with specific "SIP alert Info" when I use my click2call server option.
My SIP server send "Ring Answer" or "info=alert-autoanswer" (I can choose it).
In this case the Yealink phone goes in autoanswer and the recall start.
It is very well, but I wish to know the specification of your Autoanswer feature.
Is it possible to modify the delay of autoanswer?There are some option in the .cfg file config?

Thank you for support
Regards
Walter
04-10-2014 11:22 PM
     Quote this message in a reply
CWR Offline
Moderator
*****

Posts: 716
Joined: May 2013
Reputation: 7
Post: #2
RE: Autoanswer on click to dial feature
On the T46 and T26 I find under Features->General Information: Auto-Answer Delay(1~4s)
The config option is:
#Configure the delay time (in seconds)of auto answer. The time ranges from 1 to 4, the default value is 1s.
features.auto_answer_delay =

But I do not see this on the T38...

Craig Reilly
MCSA, 3cx Advanced Certified
Scottsdale, AZ
04-11-2014 01:54 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Walter
Unregistered

 
Post: #3
RE: Autoanswer on click to dial feature
dear craigreilly,
I have found this option in the new fw vers 6.72.0.30 and tomorrow I will test if it works.
I done another test adding features.auto_answer_delay = 3
in the privisioning file config into another T26 with old fw version 6.70.0.120 but it answer always at the first ring. I find a similar thread here
http://forum.yealink.com/forum/showthrea...autoanswer
Anyway, is there a specification about the kind of "SIP Alert Info" that the telephone needs for enabling the auto answer?
thank you
Walter
04-11-2014 04:22 AM
     Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,684
Joined: Dec 2012
Reputation: 24
Post: #4
RE: Autoanswer on click to dial feature
sip: INVITE messages include the following headers:
• Alert-Info: Auto Answer
• Call-Info: answer-after=0
04-11-2014 11:15 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Walter
Unregistered

 
Post: #5
RE: Autoanswer on click to dial feature
Dear Support,
I have modified the INVITE header from my sip server
Call-Info: <sip:127.0.0.1>;answer-after=3
Alert-Info: Ring Answer

and now the T26 delays the autoanswer correctly.

Another quick question only for my clarification;
how does the features.auto_answer_delay option work and when is it operative?

BR
Walter
04-11-2014 10:57 PM
     Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,684
Joined: Dec 2012
Reputation: 24
Post: #6
RE: Autoanswer on click to dial feature
This syntax only take effect when you have enabled auto answer and server can sent correct call info header to phone.
Now you can test to change this syntax and test again.
04-12-2014 11:30 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Walter
Unregistered

 
Post: #7
RE: Autoanswer on click to dial feature
Dear Support,
regarding the syntax and the call info header from my server is whole clear.

Now my question is about the telephone web interface: into the menu "Features >> General Informations I find the "Auto-Answer Delay(1~4s)" (see the figure attached).
   
How does this parameter work?. When does this parameter take effect?

Regards
Walter
04-14-2014 03:08 PM
     Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,684
Joined: Dec 2012
Reputation: 24
Post: #8
RE: Autoanswer on click to dial feature
This feature is a custom feature. It is a phone feature that will ring doulbe times when a call comes in.
If you set Auto-Answer Delay(1~4s) as 1, the coming call which server doesn't send auto-answer header will ring two times and auto answered.
(This post was last modified: 04-15-2014 11:30 AM by Yealink Support.)
04-15-2014 11:29 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
jmoore Offline
Junior Member
**

Posts: 36
Joined: Jan 2016
Reputation: -1
Post: #9
RE: Autoanswer on click to dial feature
Hello,

I see you're asking about click to dial. I work for a company that offers this feature and creates a call record for every call, incoming and outgoing. Some of the information logged for each call include:

- Call Duration
- Direction (inbound vs. outbound)
- Name of user who made or received the call
- If it's an inbound call, the inbound extension (for example the queue or phone number it came in on)
- User extension (the extension of the user that answered the call)
- User device (i.e. cell phone vs. desk phone)
- Call notes entered by the user

All of this information is automatically linked to the contact/lead/account by phone number and the user has the flexibility to enter any pertinent information they deem useful. We have integrations with this platform:
https://www.callinize.com/integrations/yealink/

Hope this helps!
05-04-2016 05:42 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  V84 feature blf.enhanced brourk 4 2,587 10-04-2019 12:32 AM
Last Post: Oregon
  T28P & T38G: Speed Dial delay or pause between DTMF yoda72 70 199,693 08-18-2019 09:06 PM
Last Post: HotlineExperts
  CP960 with SFB protect Basic and Feature settings geislinger 2 2,036 08-12-2019 01:15 PM
Last Post: geislinger
  Click to dial from web browser h2g-vaka 4 4,117 03-15-2019 07:53 AM
Last Post: banderlog
  Which RFC describes as-feature-event event package ? oliv 3 3,968 01-16-2019 04:45 PM
Last Post: jolouis
  Dial from Windows Pox 0 1,545 11-06-2018 02:52 PM
Last Post: Pox
  Dial Now Rule Issue when Transfer IPBX 3 4,245 03-19-2018 04:26 PM
Last Post: IPBX
  How to disable the Dial-Upon-Lift feature Jeremy17 1 3,017 12-11-2017 01:33 AM
Last Post: Evan_Yealink
  Network Conference feature Sur 11 8,989 11-07-2017 07:25 AM
Last Post: Sur
  redial with dial plan Leandro Freire 4 5,554 10-28-2017 05:20 PM
Last Post: Leandro Freire

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication