[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Intercom Barge
Author Message
davemcbr Offline
Junior Member
**

Posts: 5
Joined: Apr 2016
Reputation: 0
Post: #1
Intercom Barge
Hi Support!

When a T46G user is on the line, and someone pages or intercoms them, it puts the first call on hold automatically, and then after the page they can resume the first call (barge in).

This happens even though call barge is disabled on the phone.


using :


Firmware: T46-28.80.0.95

Call-info:answer-after=0

Intercom barge : Disable

Using Mangovoice

Works great with all other manufacturers


i also have Alert-Info: <alert-internal> for internal ringing set. I dont know if that makes any difference
04-16-2016 02:29 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Karl_Yealink Offline
Super Moderator
******

Posts: 673
Joined: Apr 2015
Reputation: 5
Post: #2
RE: Intercom Barge
I test here, my phones work normally.
Can you try to reset the phone then test again.
You can press the OK button about 10 sec to reset the phone.
04-16-2016 05:50 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
davemcbr Offline
Junior Member
**

Posts: 5
Joined: Apr 2016
Reputation: 0
Post: #3
RE: Intercom Barge
(04-16-2016 05:50 AM)Yealink_Karl Wrote:  I test here, my phones work normally.
Can you try to reset the phone then test again.
You can press the OK button about 10 sec to reset the phone.

Karl,

Thank you for your response. However that did not work. I have a couple thousand phones acting this way from t41,42,46,and 48. The yealink phone still allows barging on active call. I have treid with many different yealink phones. If I sent you some registration information, would you mind registrating a phone to dev pbx. so you can see the issue? Also I noticed I also have intercom=true as part of the invite.

When testing. Barge disable work fine on 36.73.0.50 and breaks on 36.80.0.60 and above, does not honor barge disable. Meaning when on an active call, it will put that call on hold when a intercom call comes in.
(This post was last modified: 06-11-2016 06:07 AM by davemcbr.)
06-11-2016 04:14 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  T4X no beep on intercom answer jcaruso 2 7,288 04-12-2022 04:46 AM
Last Post: JohnJ
Wink Intercom and BLF eric@salemcomputer.com 4 9,104 11-04-2020 12:39 AM
Last Post: remingtonsmith
  Intercom tone - make louder? imfloridaguy 7 17,838 09-22-2020 06:54 PM
Last Post: Nraphan
Information Increase intercom tone value support@thearcehouse.com 14 30,571 09-22-2020 06:52 PM
Last Post: Nraphan
  Ring Mute while keeping intercom ring on Problemchild 1 8,290 05-09-2018 09:00 AM
Last Post: Kevin_Yealink
  T46G Firmware 28.80.0.60 disables the intercom auto-answer function KenDoerksen 11 33,900 07-28-2017 06:05 AM
Last Post: Lucia_Yealink
  T48G Intercom Auto-answer cm21 14 37,663 03-06-2017 08:48 PM
Last Post: engine411
  Anyone have sucecss using the Intercom with Vonage? saul 4 12,947 02-28-2017 01:36 PM
Last Post: saul
  T46G - - Intercom - Call Barge Issue Abe1048 15 58,237 06-18-2016 04:43 AM
Last Post: davemcbr
  intercom auto-answer T46G to Zultys. dew3flr 1 6,504 01-30-2016 05:35 AM
Last Post: Yealink_Michael

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication