[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Call pickup on BLF not working on 7.72.0.1 [resolved 7.72.0.56.rom]
Author Message
Yealink Support Offline
Administrator
*******

Posts: 2,683
Joined: Dec 2012
Reputation: 25
Post: #11
RE: Call pickup on BLF not working on 7.72.0.1
Hi Tecno,
1. Please upgrade to the latest version x.72.0.25 and test again.
2. In order to do more troubleshootings, please supply me syslog level 6, config.bin and pcap. How to Get the Correct Syslog, Config.bin and Trace
03-04-2014 03:40 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Tecno Offline
Junior Member
**

Posts: 19
Joined: Dec 2012
Reputation: 0
Post: #12
RE: Call pickup on BLF not working on 7.72.0.1
i Upgrade to lastest version 2.72.0.30, but a same results, the pickup not work.





P.D. In the version 2.60.23.8 work fine!!!!


Attached File(s)
.tar  syslog.tar (Size: 229.5 KB / Downloads: 13)
.bin  config.bin (Size: 182 KB / Downloads: 2)
(This post was last modified: 03-07-2014 04:19 AM by Tecno.)
03-07-2014 02:12 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
temp0001 Offline
Junior Member
**

Posts: 16
Joined: Jan 2014
Reputation: 0
Post: #13
RE: Call pickup on BLF not working on 7.72.0.1
Here are the exported files, with one set for the phone running v61 and one set on v72.

I started pcap after the phone was booted.
Then I made an incoming call to the other extension.
When the BLF key started blinking, I pressed it.

In v61, I hung up the call after it was picked up via BLF.
In v72, the call could not be picked up, so I hung up from the calling phone.

After this, I stopped pcap and exported the three files.

v61 pcap, syslog and config.bin:

.zip  7.61.0.80_config_pcap_syslog.zip (Size: 93.45 KB / Downloads: 2)

v72 pcap, syslog and config.bin:

.zip  7.72.0.1_config_pcap_syslog.zip (Size: 52.12 KB / Downloads: 5)

I had to zip up the files because your forum software limits the number of attachments to 5 files.
03-07-2014 01:21 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Tecno Offline
Junior Member
**

Posts: 19
Joined: Dec 2012
Reputation: 0
Post: #14
RE: Call pickup on BLF not working on 7.72.0.1
Please help!
(This post was last modified: 03-11-2014 03:38 AM by Tecno.)
03-11-2014 02:12 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,683
Joined: Dec 2012
Reputation: 25
Post: #15
RE: Call pickup on BLF not working on 7.72.0.1
(03-11-2014 02:12 AM)Tecno Wrote:  Please help!
Some one experience similar issue as yours. Please check weather your server is Asterisk or Asterisk based.
"The Setting in "Account" -> "Advanced" -> (Account Number) -> "Dialog-Info Call Pickup" must be DISABLED.
Otherwise "Call Pickup on BLF" doesn't work on Asterisk PBX. "

BLF and Call Pickup

Some other servers need to BLF using dialog-info, so please check to enable or disable it and test again.
(This post was last modified: 03-11-2014 07:13 PM by Yealink Support.)
03-11-2014 07:05 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,683
Joined: Dec 2012
Reputation: 25
Post: #16
RE: Call pickup on BLF not working on 7.72.0.1
(03-07-2014 01:21 PM)temp0001 Wrote:  Here are the exported files, with one set for the phone running v61 and one set on v72.

I started pcap after the phone was booted.
Then I made an incoming call to the other extension.
When the BLF key started blinking, I pressed it.

In v61, I hung up the call after it was picked up via BLF.
In v72, the call could not be picked up, so I hung up from the calling phone.

After this, I stopped pcap and exported the three files.

v61 pcap, syslog and config.bin:


v72 pcap, syslog and config.bin:


I had to zip up the files because your forum software limits the number of attachments to 5 files.
Thanks to your files. I will submit to your issue to our R&D.
03-11-2014 07:16 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,683
Joined: Dec 2012
Reputation: 25
Post: #17
RE: Call pickup on BLF not working on 7.72.0.1
Hi temp0001,

Please test below solved version and kindly feed back to me.
7.72.0.56.rom
04-02-2014 04:37 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
temp0001 Offline
Junior Member
**

Posts: 16
Joined: Jan 2014
Reputation: 0
Post: #18
RE: Call pickup on BLF not working on 7.72.0.1
THANK YOU!!!

I just tested the 7.72.0.56.rom. BLF pickup is working again!

I upgraded the firmware on one phone (running 7.72.0.1 where it previously wasn't working) and it started working right away.
On another phone running 7.61.0.80, the upgrade to 7.72.0.56 is also fine.

In both cases, it worked without further configuration.

This is great news for others having the same problem.

EDIT: Also, will this fix be incorporated into the next firmware release for the T28P?
(This post was last modified: 04-04-2014 10:04 AM by temp0001.)
04-04-2014 07:52 AM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Tecno Offline
Junior Member
**

Posts: 19
Joined: Dec 2012
Reputation: 0
Post: #19
RE: Call pickup on BLF not working on 7.72.0.1 [resolved 7.72.0.56.rom]
Hi Support:

I need this fix for T28 Phones.


Regards
04-09-2014 09:43 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,683
Joined: Dec 2012
Reputation: 25
Post: #20
RE: Call pickup on BLF not working on 7.72.0.1 [resolved 7.72.0.56.rom]
Hi Tecno,

We will fix this issue in V73 for all T2 series. Thanks to your kindly understanding.
04-10-2014 04:15 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Call forwarding with SIP devices Yealink and Cisco Call Manager CUCM joao.schlemm 8 24,869 12-27-2023 06:49 PM
Last Post: nolto
  T28P foward call doesn´t work with 2.73.0.50 Tato 4 11,556 09-14-2020 03:49 PM
Last Post: complex1
  default username/password not working after firmware upgrade tfrohling 3 37,564 02-15-2020 01:30 PM
Last Post: khalidnisar
  Attended transfer not working T29G chysky@slany.cz 1 6,284 02-11-2020 02:48 PM
Last Post: chysky@slany.cz
  T21P backlight not working after F/W update donb 0 4,562 11-07-2019 02:29 PM
Last Post: donb
  T22P Action URI ATrans and BTrans not working? DaveThompson 2 12,035 09-10-2019 10:47 AM
Last Post: DaveThompson
  Yealink T27G Not Working With 802.1x Auth After 3cx v14 to v15.5 Upgrade KM Tire IT Support 1 7,032 10-18-2018 05:06 PM
Last Post: KM Tire IT Support
Photo Yealink T21P E2 displays VIA and FROM headers on incoming call DmitryTsyganov 1 7,034 07-12-2018 07:28 PM
Last Post: johnkiniston
  T21P-E2 sends a CANCEL to put a call in hold Diego Juan 0 4,896 03-23-2018 02:52 PM
Last Post: Diego Juan
  Call Queue not working with the Grandstream UCM6202 ttran 8 22,119 03-04-2018 06:42 PM
Last Post: Adnanka

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication