[YMCS/YDMP Free Trial Program]Yealink would like to offer Free Trial Program of Yealink device management service for our current eligible customers. You can see the details below.
https://www.yealink.com/ydmp-freetrial-2020


Post Reply 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
User Must Hit Answer and When Calls End they go to Speaker
Author Message
jaywa73 Offline
Junior Member
**

Posts: 4
Joined: Dec 2013
Reputation: 0
Post: #1
User Must Hit Answer and When Calls End they go to Speaker
I'm not sure if I have a bad T28 phone on my hands or I'm missing something. I'm rather new to Yealink phones but am trying to learn.

I have a 2 users who when they are called from the reception phone pick up their handsets and have to press "Answer" to accept the call. Also, one of them has reported that when she's done with a call and puts the handset in the cradle it makes the call go to speaker instead of terminating the call.

All other phones in the group pick up intercom calls when the handset is picked up and terminates the call when the handset is put down.

Any ideas? Phones in question are T28 and have the 2.71.0.165 firmware installed.

Thank you.
12-03-2013 10:11 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Yealink Support Offline
Administrator
*******

Posts: 2,683
Joined: Dec 2012
Reputation: 25
Post: #2
RE: User Must Hit Answer and When Calls End they go to Speaker
Hi jaywa73,

Sorry for the inconvenience.

1. Are other phones yealink phones?
2. Which PBX do you use?
3. Please enter the webpage->Features->General Information, find Dual-Headset, check whether you have enabled it.
If yes, that you have to press "Answer" to accept the call. So please disable it, then the hook can work well now.

4. "Also, one of them has reported that when she's done with a call and puts the handset in the cradle it makes the call go to speaker instead of terminating the call."
If your customer pressed speaker button after picked up the handset, then phone will run a multicast mode. Then above phenomenon will happen. Can you double check about that?
12-04-2013 03:46 PM
Find all posts by this user    like0    dislike0 Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  T48S One Way Audio When Calls Are Put On Hold Or Transferred MJauja 1 295 03-09-2024 08:48 PM
Last Post: complex1
  Unable to Answer call without pressing Line 1 TheKirbyGroup 0 646 11-03-2023 11:04 PM
Last Post: TheKirbyGroup
  Yealink T19 can not automatically hangup inbound calls giaopc94 0 1,634 08-01-2022 09:28 AM
Last Post: giaopc94
  Missed calls list... caller id.. outbound route pattern savi 0 1,855 06-05-2022 03:09 PM
Last Post: savi
  Limit maximum of active calls per phone elastalink 5 15,056 09-09-2021 03:52 AM
Last Post: kapetrosyan
  Display Caller Picture on internal calls via LDAP dawgness 6 22,294 03-07-2019 01:41 AM
Last Post: scubes
  Ring-beep on internal busy calls lupacexi 1 7,618 12-11-2017 02:47 AM
Last Post: Evan_Yealink
Question speaker on auto answer Sergey_9_ 8 18,527 07-07-2017 08:01 AM
Last Post: Lucia_Yealink
  Ring-beep on internal busy calls xptpa2020 2 9,213 03-10-2017 07:47 AM
Last Post: Klaus_Yealink
  Missed Calls messages after pickup and in queues Kamik 2 9,605 12-14-2016 07:05 PM
Last Post: nick.spannagel

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us   Yealink   Return to Top   Return to Content   Lite (Archive) Mode   RSS Syndication