How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - Printable Version +- Yealink Forums (http://forum.yealink.com/forum) +-- Forum: IP Phone Series (/forumdisplay.php?fid=4) +--- Forum: Auto Provisioning (/forumdisplay.php?fid=14) +--- Thread: How do I set ILBC_enabled = 0 to ILBC_enabled = 1 (/showthread.php?tid=547) |
How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - Hoenle - 06-16-2013 06:10 PM Via auto provisioning on the .70 version of the firmware? I've tried: Advanced.ILBC_enabled = 1 and ILBC_enabled = 1 without success. Is this change still required to use the iLBC codec? Thank you! RE: How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - Yealink Support - 06-17-2013 10:31 AM Hi Hoenle, Do you have our V70 auto provisioning template? http://www.yealink.com/Upload/AutoProvisoning-17095068456.zip In the MAC-Oriented.cfg file, you can find this paramter: ------------------------------- account.1.codec.7.enable = 1 account.1.codec.7.payload_type = iLBC account.1.codec.7.priority = 0 account.1.codec.7.rtpmap = 102 ------------------------------- Thanks. RE: How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - Hoenle - 06-17-2013 05:46 PM Hi there! Yes, I have the template but none of those options seem to change the ILBC_enabled = 0 line in the user.ini (in the configuration downloaded from the phone) ;;Advanced.cfg [ Advanced ] password = var_enabled = 0 iStandardOrAdvanced = 1 ILBC_enabled = 0 Is this setting no longer required? RE: How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - Yealink Support - 06-18-2013 10:22 AM Hi Hoenle, 1. Which phone are you using? And what's the firmware? 2. Do you mean after you auto provisioning with ------------------------------- account.1.codec.7.enable = 1 account.1.codec.7.payload_type = iLBC account.1.codec.7.priority = 0 account.1.codec.7.rtpmap = 102 ------------------------------- But the phone didn't enable ILBC codec? RE: How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - wuuikok - 07-11-2013 12:07 AM Anyone has successfully do this? I still cannot find anyway to enable iLBC using auto provisioning. I only missed this step, set the ILBC_enabled = 1. Thanks RE: How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - briankelly63 - 07-11-2013 12:45 AM Just to back up a little..... Have you been successful with other provisioning on this setup and phone? Just want to make sure the phone is really reading the file. What is your provisioning setup? tftp, http?? RE: How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - wuuikok - 07-11-2013 01:06 AM I have been successfully auto provisioning the Yealink phone T20 using tftp setup. Below is the log from my tftp server Jul 11 00:41:37 ocapp xinetd[18207]: START: tftp pid=25694 from=10.8.0.62 Jul 11 00:41:37 ocapp in.tftpd[25695]: RRQ from 10.8.0.62 filename y000000000007.cfg Jul 11 00:41:47 ocapp in.tftpd[25701]: RRQ from 10.8.0.62 filename client.tar Jul 11 00:41:47 ocapp in.tftpd[25703]: RRQ from 10.8.0.62 filename 9.70.23.2.rom Jul 11 00:41:47 ocapp in.tftpd[25704]: RRQ from 10.8.0.62 filename 0015654ab601.cfg Jul 11 00:42:18 ocapp in.tftpd[25703]: tftpd: read(ack): Connection refused RE: How do I set ILBC_enabled = 0 to ILBC_enabled = 1 - briankelly63 - 07-11-2013 03:36 AM Please check the phones log to make sure its actually getting the file. This may all be for nothing if you have been able to successfully change other items. The only reason I mention it is that the tftp server log only shows the request that was made, it doesn't show if the phone actually was able to access, open and read the file. Usually that is seen from the phone log or syslog. See Export log in the phone Administration manual. The last statement in the log concerns me as it may be a permissions or directory issue. You may be able to turn on a higher level of debug commentary in your tftp server. |