Yealink Forums
T41P with YHS32 Headset Microphone Volume Issue - Printable Version

+- Yealink Forums (http://forum.yealink.com/forum)
+-- Forum: IP Phone Series (/forumdisplay.php?fid=4)
+--- Forum: T4x Series (/forumdisplay.php?fid=31)
+--- Thread: T41P with YHS32 Headset Microphone Volume Issue (/showthread.php?tid=4201)



T41P with YHS32 Headset Microphone Volume Issue - dman84 - 08-03-2015 09:16 AM

Hi All

I am using a few T41P Handsets with YHS32 Headsets and finding that the Microphone Volume is very low. The web interface appears to have no option for increasing the Mic Volume or Gain and I was hoping that someone may have a solution for this?

I am using Firmware Version 36.73.0.50 the handsets also.

Thank you very much in advance Smile
Dan


RE: T41P with YHS32 Headset Microphone Volume Issue - Karl_Yealink - 08-03-2015 04:24 PM

Hi,

1.Please upgarde to lastest firmware
2.If it does not work,please kindly reset to factory setting and try again.
3.If the above checking does not work.You can auto privisioning the parameter below to increase the mic volume.
voice.headset_send=
Integer from -50 to 50,the deafult is 0.
But we do not sugget customer change the parameter of change the number to high.
Because it may render the voice quality bad.


RE: T41P with YHS32 Headset Microphone Volume Issue - Remko Schenk - 08-10-2015 08:07 PM

Hi Yealink,

We have the same problem with a Sennheiser heaset, the SC260, in combination with the T41. We use 3CX.
This headset is an tested headset and is on the Yealink tested headset list.
The microphone volume of that headset is to low.

I have tested with different firmware levels, also with the latest V36.80.0.70 firmware. no better results.
I have tested with the provisioning settings for "voice.headset_send = ", as named in several threads on the Yealink forum.
In some threads is the setting between -120 to 30 and in this thread you named between -50 and 50. I have tried all but no better result.

Can you please tell me what the solution is?

greets Remko


RE: T41P with YHS32 Headset Microphone Volume Issue - Karl_Yealink - 08-11-2015 01:12 AM

Hi,

1.Sennheiser SC260 need wireless headset connection of Sennheiser 5362-CSTD 01 Cables,do you have it?
2.Please kindly reset to factory setting and try again.
3.The default parameter in V80 version between -50 and 50.


RE: T41P with YHS32 Headset Microphone Volume Issue - Remko Schenk - 08-11-2015 08:43 PM

Hi Karl,

1. Yes we have the 5362-CSTD 01, otherwise we cann't connect the headset. This is an wired headset, not wireless.
2. yes we have factory default it, but in our envirement the phone gets with LDAP the right VLAN and configuration from 3CX.
In that case the phone gets no voice.headset_send information because this isn't in the template.
3. thanks for the right parameters. I have tested it in the template with 3CX and there is no improvement, it still keeps very low mic volume.

ok, i did a factory reset with 36.80.0.70 firmware and manually programmed the account. The voice send volume is better.
I think that the provisioning by 3CX the voice.headset_send parameter isn't functioning. When I provisioning the phone by default template the send volume is lower then by factory defaults. When I try an other value (by example 48) there is no difference, the volume keeps low.

Do you have an suggestion?

Regards Remko


RE: T41P with YHS32 Headset Microphone Volume Issue - Karl_Yealink - 08-12-2015 12:37 AM

Hi,

Can you help to get config.bin file. We can check something from them.
A config.bin when you provisioning the phone by default template.
A config.bin when you try an other value (by example 48).
The files can be got from phone web interface-> Setting-> Configuration->Export or Import Configuration,
and export the file.


RE: T41P with YHS32 Headset Microphone Volume Issue - Remko Schenk - 08-13-2015 04:50 PM

Hi Karl,

I have attached th bin files.

Best regards Remko.


RE: T41P with YHS32 Headset Microphone Volume Issue - Karl_Yealink - 08-15-2015 01:04 AM

Hi,

From the bin files. I find the headset-send-volume = 1 in three files.
So you maybe can't auto provisioning succeed.


RE: T41P with YHS32 Headset Microphone Volume Issue - Remko Schenk - 08-20-2015 09:12 PM

Hi Karl,

I found out that the problem is with provisioning by 3CX.
When added that line and checking by MAC-template, its not in that template.
So its normal that its also not in the phone.
I have made a ticket by 3CX support an d wait for a answer.

Best regards Remko


RE: T41P with YHS32 Headset Microphone Volume Issue - ausadmin - 11-24-2015 08:46 AM

FWIW, I was able to adjust up the headset and handset mic volume on one of our T41P phones (running 36.80.0.60) as follows
- export all configuration
- add the following lines to the file
voice.headset_send = 40
voice.handset_send = 10
- import all configuration

Regards,
Tim