Yealink Forums
Yealink 28.82.0.20 - Printable Version

+- Yealink Forums (http://forum.yealink.com/forum)
+-- Forum: IP Phone Series (/forumdisplay.php?fid=4)
+--- Forum: T4x Series (/forumdisplay.php?fid=31)
+--- Thread: Yealink 28.82.0.20 (/showthread.php?tid=41335)

Pages: 1 2


RE: Yealink 28.82.0.20 - engine411 - 12-14-2017 03:21 AM

Any update on this?


RE: Yealink 28.82.0.20 - Lucia_Yealink - 12-14-2017 07:45 AM

(12-14-2017 03:21 AM)engine411 Wrote:  Any update on this?

Send you an email about the solution, please check.

BR
Lucia


RE: Yealink 28.82.0.20 - DamianFerrari - 01-08-2018 12:58 PM

I've installed this firmware (28.82.0.20) to 110 Yealink T42G and 1 of them stack at Welcome screen. I could recovered the phone after recover procedure but when I try to install the new firmware again it goes to Welcome screen and stack.


Version
Firmware Version 29.71.0.120
Hardware Version 29.1.0.0.0.0.0
MAC Address 0015658189b3

serial: 8109114111001948


The most recent firmware I could install is: Firmware Version 29.81.0.110


RE: Yealink 28.82.0.20 - Garan - 07-11-2018 08:55 PM

(12-14-2017 07:45 AM)Lucia_Yealink Wrote:  
(12-14-2017 03:21 AM)engine411 Wrote:  Any update on this?

Send you an email about the solution, please check.

BR
Lucia

Can you post the solution here please? I have been tracking this down for days now from the 3cx message board to here and everywhere in between.

I"m having the same EXACT issue, which also persists on the latest 3CX 83 firmware.


RE: Yealink 28.82.0.20 - Garan - 08-10-2018 07:41 PM

(07-11-2018 08:55 PM)Garan Wrote:  
(12-14-2017 07:45 AM)Lucia_Yealink Wrote:  
(12-14-2017 03:21 AM)engine411 Wrote:  Any update on this?

Send you an email about the solution, please check.

BR
Lucia

Can you post the solution here please? I have been tracking this down for days now from the 3cx message board to here and everywhere in between.

I"m having the same EXACT issue, which also persists on the latest 3CX 83 firmware.

PM'ed, can anyone help?

Also,

Neither transfer nor conference work, either.


RE: Yealink 28.82.0.20 - Garan - 08-29-2018 04:06 PM

More details here:

https://www.3cx.com/community/threads/park-issues-revisited.58633/#post-246560

Problem still exists, I have narrowed it down to the following settings that are being applied despite either not being specified at all, or being specified to another value in my provisioning file. This seems to be the culprit but I can find no cause for this. Very annoying.

features.call_park.park_mode = 0
bw.enable = 1



RE: Yealink 28.82.0.20 - Garan - 08-29-2018 06:00 PM

(08-29-2018 04:06 PM)Garan Wrote:  More details here:

https://www.3cx.com/community/threads/park-issues-revisited.58633/#post-246560

Problem still exists, I have narrowed it down to the following settings that are being applied despite either not being specified at all, or being specified to another value in my provisioning file. This seems to be the culprit but I can find no cause for this. Very annoying.

features.call_park.park_mode = 0
bw.enable = 1

Fixed.

The following was set in my provisioning file, not sure for what reason exactly. But it must require bw.enable =1 as a dependency and automatically set it, which as I understand then limits you to FAC only on park mode:

bw.directory_enable = 1

I set it to 0 and it is working correctly.

Hopefully this helps someone else.