+- Yealink Forums (http://forum.yealink.com/forum)
+-- Forum: IP Phone Series (/forumdisplay.php?fid=4)
+--- Forum: T4x Series (/forumdisplay.php?fid=31)
+--- Thread: New parameter features.call_park.park_mode = 0 in local configuration on upgrade (/showthread.php?tid=29924)
New parameter features.call_park.park_mode = 0 in local configuration on upgrade - ipcsolutions - 10-10-2016 05:20 PM
On upgrade (I think only on T46G) to .130 (could be earlier releases), the configuration features.call_park.park_mode = 0 is set in local configuration.
By default call_park.park_mode = 2 so this breaks most Call Park implementations.
Once removed from Local Configuration, features.call_park.park_mode = 2 and everything works fine.
Can this problem please be fixed.
Thanks
Mike
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade - Kevin_Yealink - 10-11-2016 03:04 PM
(10-10-2016 05:20 PM)ipcsolutions Wrote: On upgrade (I think only on T46G) to .130 (could be earlier releases), the configuration features.call_park.park_mode = 0 is set in local configuration.
By default call_park.park_mode = 2 so this breaks most Call Park implementations.
Once removed from Local Configuration, features.call_park.park_mode = 2 and everything works fine.
Can this problem please be fixed.
Thanks
Mike
Hi Mike
This is Kevin from yealink support team, nice to know you.
For this issue, can you tell me the firmware of the phone, and the earlier firmware.
Becase in the 28.80.0.130, then value is 2 by default. For the broad firmware, it is 0 by default.
BR
Kevin
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade - ipcsolutions - 10-12-2016 07:29 AM
I suspect that the earlier firmware was T46-28.80.0.95 and I upgraded to T46-28.80.0.130.
Thanks
Mike
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade - Kevin_Yealink - 10-13-2016 04:40 PM
(10-12-2016 07:29 AM)ipcsolutions Wrote: I suspect that the earlier firmware was T46-28.80.0.95 and I upgraded to T46-28.80.0.130.
Thanks
Mike
Hi I test in my side , and the park mode on .130 firmware is 2 by default. So please check if you enable broadsoft in the .95.
BR
Kevin
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade - ipcsolutions - 10-13-2016 06:09 PM
Unfortunately I cant confirm what it was previously so this could have been the issue. I will monitor on the next lot of phones I install.
Thanks
Mike
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade - Kevin_Yealink - 10-14-2016 06:44 PM
(10-13-2016 06:09 PM)ipcsolutions Wrote: Unfortunately I cant confirm what it was previously so this could have been the issue. I will monitor on the next lot of phones I install.
Thanks
Mike
Hi Mike
Let me know if any update.
BR
Kevin
RE: New parameter features.call_park.park_mode = 0 in local configuration on upgrade - ipcsolutions - 11-08-2016 10:10 AM
Hi Kevin
I can confirm that all phones I have installed straight out of the box (T41 & T46) when upgraded to 0.130 have features.call_park.park_mode = 0 is set in local configuration.
This is really annoying as I need to remove it manually from the Web GUI for all phones. Can I remove it a different way?