Yealink Forums
T20P firmware from 9.60.0.99 - Printable Version

+- Yealink Forums (http://forum.yealink.com/forum)
+-- Forum: IP Phone Series (/forumdisplay.php?fid=4)
+--- Forum: Phone specific topic (/forumdisplay.php?fid=12)
+---- Forum: T2xP Series (/forumdisplay.php?fid=21)
+---- Thread: T20P firmware from 9.60.0.99 (/showthread.php?tid=2547)



T20P firmware from 9.60.0.99 - Istvan - 10-13-2014 07:32 PM

Hi,
I have a T20P phone which has the firmware of 9.61.0.99 and it seems I need to upgrade to the highest version possible, as we are experiencing problems with our voip provider (sonetel.com).
However, the instructions to move to firmware 70 are just too complex.
I have exported our config from the phone, this is config.bin.
But I can't find any form of y00000001.cfg, etc. anywhere, nor mac.cfg.
Also, I don't know what you mean by configuration server, shall I just put the files to any webserver and that's it?
So I am lost. It is just one phone.
Please help.
Thanks
Istvan


RE: T20P firmware from 9.60.0.99 - Yealink_Jim - 10-15-2014 09:57 AM

Hi Istvan,
Usually, we have two methods of firmware upgrade:
1. Upgrade via Web User Interface. (Manually, from the local system for a single phone)
2. Upgrade Firmware via Auto Provisioning. (Automatically, from the provisioning server for a mass of phones)
I suggest that you can upgrade via Web User Interface.

[Image: attachment.php?aid=1076]

Please go to below URL to get more information:

http://forum.yealink.com/forum/showthread.php?tid=1420

Yealink IP phones support using FTP, TFTP, HTTP and HTTPS protocols to download configuration files. If the webserver support to these protocols, You can use one of these protocols for provisioning. You can refer to below Auto Provisioning guide for more information:

http://www.yealink.com/Upload/T2X/2014.3.4/Yealink_SIP-T2_Series_IP_Phones_Auto_Provisioning_Guide_V72_30.pdf

Hope this helps!


RE: T20P firmware from 9.60.0.99 - Istvan - 10-17-2014 01:40 AM

Thanks, does this mean that if I update using the web interface, there is no need to convert any settings files and mac files and the like?


RE: T20P firmware from 9.60.0.99 - Yealink_Jim - 10-20-2014 03:22 PM

(10-17-2014 01:40 AM)Istvan Wrote:  Thanks, does this mean that if I update using the web interface, there is no need to convert any settings files and mac files and the like?

You need to make sure that the correct configuration parameters


RE: T20P firmware from 9.60.0.99 - Istvan - 10-23-2014 02:45 AM

(10-20-2014 03:22 PM)Yealink_Jim Wrote:  
(10-17-2014 01:40 AM)Istvan Wrote:  Thanks, does this mean that if I update using the web interface, there is no need to convert any settings files and mac files and the like?

You need to make sure that the correct configuration parameters

Please check you message, it seems to be incomplete.


RE: T20P firmware from 9.60.0.99 - Istvan - 11-04-2014 08:50 PM

Please complete your response of 10-20-2014 10:22 AM, Yealink_Jim, until that I cannot proceed. Thanks.


RE: T20P firmware from 9.60.0.99 - Yealink_Jim - 11-05-2014 09:13 AM

Hi Istvan,
Yes, if you upgrade using the web interface, you don't need to convert any settings files and mac files and the like.


RE: T20P firmware from 9.60.0.99 - Mmadera - 01-12-2016 11:03 PM

to firmware upgrade its simply:

downlaod the ne w firmware http://support.yealink.com/documentFront/forwardToDocumentDetailPage?documentId=19#frnotes
in the phone web page (you must know wich ip actually use, just press menu and ok in the phone and it shows)
go to configure, upgrade, select the file donwloaded previously and wait to finish

hope this helps